One of the main challenges in deep-water drilling is gas-hydrate plugs,which make the drilling unsafe.Some oil-based drilling fluids（OBDF） that would be used for deep-water drilling in the South China Sea were teste...One of the main challenges in deep-water drilling is gas-hydrate plugs,which make the drilling unsafe.Some oil-based drilling fluids（OBDF） that would be used for deep-water drilling in the South China Sea were tested to investigate the characteristics of gas-hydrate formation,agglomeration and inhibition by an experimental system under the temperature of 4 ？C and pressure of 20 MPa,which would be similar to the case of 2000 m water depth.The results validate the hydrate shell formation model and show that the water cut can greatly influence hydrate formation and agglomeration behaviors in the OBDF.The oleophobic effect enhanced by hydrate shell formation which weakens or destroys the interfacial films effect and the hydrophilic effect are the dominant agglomeration mechanism of hydrate particles.The formation of gas hydrates in OBDF is easier and quicker than in water-based drilling fluids in deep-water conditions of low temperature and high pressure because the former is a W/O dispersive emulsion which means much more gas-water interfaces and nucleation sites than the later.Higher ethylene glycol concentrations can inhibit the formation of gas hydrates and to some extent also act as an anti-agglomerant to inhibit hydrates agglomeration in the OBDF.展开更多
Oil saturation was an important parameter of reservoir evaluation, which had important guiding significance for oilfield development. In this paper, the oil saturation of tight oil in G area was studied, and the origi...Oil saturation was an important parameter of reservoir evaluation, which had important guiding significance for oilfield development. In this paper, the oil saturation of tight oil in G area was studied, and the original oil saturation of the study area was studied by using the comprehensive experimental method. The original oil saturation of tight oil in the study area was determined by J function method, rock electricity method and oil-based mud coring method. The results showed that through the comparison of three experimental methods, it could be concluded that the J function method leads to the low value of oil saturation in the study area. The oil-based mud coring method was more suitable for the determination of oil saturation in this area than the other two methods because it needs to meet too many conditions and the calculation results were also low. G area was located in Qili Village, Ordos Basin.展开更多
Fault fractures usually have large openings and considerable extension. Accordingly, cross-linked gel materials aregenerally considered more suitable plugging agents than water-based gels because the latter often unde...Fault fractures usually have large openings and considerable extension. Accordingly, cross-linked gel materials aregenerally considered more suitable plugging agents than water-based gels because the latter often undergo contaminationvia formation water, which prevents them from being effective over long times. Hence, in this study, aset of oil-based composite gels based on waste grease and epoxy resin has been developed. These materials havebeen observed to possess high compressive strength and resistance to the aforementioned contamination, therebyleading to notable increase in plugging success rate. The compressive strength, thickening time, and resistance toformation water pollution of these gels have been evaluated indoors. The results show that the compressivestrength of the gel can reach 11 MPa;additionally, the related gelation time can be controlled to be more than3 h, thereby providing a safe construction time;Invasion of formation water has a small effect on the gel strengthand does not shorten the thickening time. All considered performance indicators of the oil-based gel confirm itssuitability as a plugging agent for fault fractures.展开更多
1-(4-ethylphenyl)-nonane-1,3-dione(0206)is an oil-soluble liquid molecule with rod-like structure.In this study,the chelate(0206-Fe)with octahedral structure was prepared by the reaction of ferric chloride and 1,3-dik...1-(4-ethylphenyl)-nonane-1,3-dione(0206)is an oil-soluble liquid molecule with rod-like structure.In this study,the chelate(0206-Fe)with octahedral structure was prepared by the reaction of ferric chloride and 1,3-diketone.The experimental results show that when using 0206 and a mixed solution containing 60%0206-Fe and 40%0206(0206-Fe(60%))as lubricants of the steel friction pairs,superlubricity can be achieved(0.007,0.006).But their wear scar diameters(WSD)were very large(532µm,370µm),which resulted in the pressure of only 44.3 and 61.8 MPa in the contact areas of the friction pairs.When 0206-Fe(60%)was mixed with PAO6,it was found that the friction coefficient(COF)decreased with increase of 0206-Fe(60%)in the solution.When the ratio of 0206-Fe(60%)to PAO6 was 8:2(PAO6(20%)),it exhibited better comprehensive tribological properties(232.3 MPa).Subsequent studies have shown that reducing the viscosity of the base oil in the mixed solution helped to reduce COF and increased WSD.Considering the COF,contact pressure,and running-in time,it was found that the mixed lubricant(Oil3(20%))prepared by the base oil with a viscosity of 19.7 mPa·s(Oil3)and 0206-Fe(60%)exhibited the best tribological properties(0.007,161.4 MPa,3,100 s).展开更多
In this study,a spent palm cooking oil-based mud with an excellent H_(2)S scavenging capability induced by the inclusion of a small quantity of potassium permanganate is formulated and tested for the first time.The mu...In this study,a spent palm cooking oil-based mud with an excellent H_(2)S scavenging capability induced by the inclusion of a small quantity of potassium permanganate is formulated and tested for the first time.The mud formulation,containing the spent palm oil as the continuous phase and water as the dispersed phase,respectively,was stabilized by Span 80 and rhamnolipid biosurfactant as primary and secondary emulsifiers,respectively,while hydrophobic zinc nanoparticles(NPs)were used as weighting agent.The results showed that H_(2)S scavenging capacity at the breakthrough time reached 182.4 g H_(2)S/barrel mud,which increased to 417.9 g H_(2)S/barrel mud at the saturation time,demonstrating the effective H_(2)S scavenging performance of the formulated mud.The spent palm oil-based mud(SPOBM)also showed a good flow behavior that could be well fitted using the Herschel-Bulkley and Casson models.The effect of temperature on the apparent viscosity of the SPOBM has been investigated,and the fitting of the viscosity-temperature data provided an estimate of the activation energy as 23.53 kJ/mol.The findings reported in this article reveal the feasibility of transforming the spent/waste cooking oils into a valuable commodity for formulating greener drilling fluids with acceptable rheology and excellent H_(2)S scavenging performance.展开更多
Natural gas is easily soluble in oil-based muds(OBM),leading to complex flow behavior in wellbores,especially in horizontal wells.In this study,a new transient flow model considering wellbore-formation coupling and ga...Natural gas is easily soluble in oil-based muds(OBM),leading to complex flow behavior in wellbores,especially in horizontal wells.In this study,a new transient flow model considering wellbore-formation coupling and gas solubility on flow behavior is developed to simulate gas kicks during horizontal drilling with OBM.Furthermore,the effect of gas solubility on parameters such as bottom-hole pressure(BHP),gas void fraction and mixture velocity in the flow behavior is analyzed.Finally,several critical factors affecting flow behavior are investigated and compared to gas kicks in water-based muds(WBM)where the effect of solubility is neglected.The results show that the invading gas exists as dissolved gas in the OBM and as free gas in the WBM.Before the gas escapes from the OBM,the pit gain is zero and there is barely any change in the BHP,annulus return flow rate and mixture velocity,which means that detecting gas kicks through these warning signs can be challenging until they get very close to the surface and develop rapidly.However,in WBM drilling,these parameters change quickly with the increasing gas kick time.Additionally,for both cases,the longer the horizontal length and the greater reservoir permeability,the greater the decrease in BHP,and the shorter the time for gas to migrate from the bottom-hole to the wellhead.A larger flow rate contributes to a greater initial BHP and a lesser BHP reduction.This research is of value in characterizing gas kick behavior and identifying novel ways for early gas kick detection during horizontal drilling with OBM.展开更多
A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based...A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based fragrance was pre-encapsulated by an inner polyacrylate membrane via solvent evaporation,followed by in situ polymerization of MF precondensates as an outer shell.The polyacrylate membrane is used as an intermediate bridging layer to stabilize the oil-based fragrance,and to provide driving forces for in situ polymerization of MF precondensates through electrostatic attractions between carboxyl groups and ammonium ions.It was demonstrated that MF microcapsules containing clove oil were prepared successfully.The amount and the composition of the intermediate polyacrylate bridging layer were critical.Smooth and sphere-shaped MF-clove oil microcapsules were prepared when the weight ratio of polyacrylate to clove oil was over 60 wt%and the concentration of acrylic acid(AA)increased to 10 wt%in polyacrylate.In addition,MF microcapsules containing sunflower oil and hexyl salicylate were prepared by using this method.The work suggests that this new approach can be potentially used to encapsulate various core materials,tuning the shell properties of microcapsules such as thickness,mechanical strength and release properties.展开更多
The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental ...The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.展开更多
Phenol is considered as pollutant due to its toxicity and carcinogenic effect.Thus,variety of innovative methods for separation and recovery of phenolic compounds is developed in order to remove the unwanted phenol fr...Phenol is considered as pollutant due to its toxicity and carcinogenic effect.Thus,variety of innovative methods for separation and recovery of phenolic compounds is developed in order to remove the unwanted phenol from wastewater and obtain valuable phenolic compound.One of potential method is extraction using green based liquid organic solvent.Therefore,the feasibility of using palm oil was investigated.In this research,palm oil based organic phase was used as diluents to treat a simulated wastewater containing 300×10^(-6) of phenol solution using emulsion liquid membrane process(ELM).The stability of water-in-oil(W/O) emulsion on diluent composition and the parameters affecting the phenol removal efficiency and stability of the emulsion;such as emulsification speed,emulsification time,agitation speed,surfactant concentration,pH of external phase,contact time,stripping agent concentration and treat ratio were carried out.The results of ELM study showed that at ratio7 to 3 of palm oil to kerosene,5 min and 1300 r·min^(-1) of emulsification process the stabile primary emulsion were formed.Also,no carrier is needed to facilitate the phenol extraction.In experimental conditions of500 r·min^(-1) of agitation speed,3%Span 80,pH 8 of external phase,5 min of contact time,0.1 mol·L^(-1) NaOH as stripping agent and 1:10 of treat ratio,the ELM process was very promising for removing the phenol from the wastewater.The extraction performance at about 83%of phenol was removed for simulated wastewater and an enrichment of phenol in recovery phase as phenolate compound was around 11 times.展开更多
In order to study the squeeze-strengthening effect of silicone oil-based magnetorheological fluid （MRF）, theoretical basis of disc squeezing brake was presented and a squeezing braking characteristics test-bed for M...In order to study the squeeze-strengthening effect of silicone oil-based magnetorheological fluid （MRF）, theoretical basis of disc squeezing brake was presented and a squeezing braking characteristics test-bed for MRF was designed. Moreover, relevant experiments were carded out and the relationship between squeezing pressure and braking torque was proposed. Experiments results showed that the yield stress of MRF improved linearly with the increasing of external squeezing pressure and the braking torque increased three times when external squeezing pressure achieved 2 MPa.展开更多
基金supported by Project 863 (No. 2006AA09Z316)NSFC (No. 50704028 and 40974071)
文摘One of the main challenges in deep-water drilling is gas-hydrate plugs,which make the drilling unsafe.Some oil-based drilling fluids（OBDF） that would be used for deep-water drilling in the South China Sea were tested to investigate the characteristics of gas-hydrate formation,agglomeration and inhibition by an experimental system under the temperature of 4 ？C and pressure of 20 MPa,which would be similar to the case of 2000 m water depth.The results validate the hydrate shell formation model and show that the water cut can greatly influence hydrate formation and agglomeration behaviors in the OBDF.The oleophobic effect enhanced by hydrate shell formation which weakens or destroys the interfacial films effect and the hydrophilic effect are the dominant agglomeration mechanism of hydrate particles.The formation of gas hydrates in OBDF is easier and quicker than in water-based drilling fluids in deep-water conditions of low temperature and high pressure because the former is a W/O dispersive emulsion which means much more gas-water interfaces and nucleation sites than the later.Higher ethylene glycol concentrations can inhibit the formation of gas hydrates and to some extent also act as an anti-agglomerant to inhibit hydrates agglomeration in the OBDF.
文摘Oil saturation was an important parameter of reservoir evaluation, which had important guiding significance for oilfield development. In this paper, the oil saturation of tight oil in G area was studied, and the original oil saturation of the study area was studied by using the comprehensive experimental method. The original oil saturation of tight oil in the study area was determined by J function method, rock electricity method and oil-based mud coring method. The results showed that through the comparison of three experimental methods, it could be concluded that the J function method leads to the low value of oil saturation in the study area. The oil-based mud coring method was more suitable for the determination of oil saturation in this area than the other two methods because it needs to meet too many conditions and the calculation results were also low. G area was located in Qili Village, Ordos Basin.
基金“Research and Application of Key Techniques for Drilling and Completion of Bozhong 19-6 Condensate Gas Field Development-Phase I”sub topic 4“Research on Leakage Prevention and Plugging Techniques for Fault and Buried Hill Reservoirs”,a Project of China National Offshore Oil (China)Co.,Ltd. (Project No.YXKY-2020-TJ-03).
文摘Fault fractures usually have large openings and considerable extension. Accordingly, cross-linked gel materials aregenerally considered more suitable plugging agents than water-based gels because the latter often undergo contaminationvia formation water, which prevents them from being effective over long times. Hence, in this study, aset of oil-based composite gels based on waste grease and epoxy resin has been developed. These materials havebeen observed to possess high compressive strength and resistance to the aforementioned contamination, therebyleading to notable increase in plugging success rate. The compressive strength, thickening time, and resistance toformation water pollution of these gels have been evaluated indoors. The results show that the compressivestrength of the gel can reach 11 MPa;additionally, the related gelation time can be controlled to be more than3 h, thereby providing a safe construction time;Invasion of formation water has a small effect on the gel strengthand does not shorten the thickening time. All considered performance indicators of the oil-based gel confirm itssuitability as a plugging agent for fault fractures.
基金supported by the National Key R&D Program of China(No.2020YFA0711003)the National Natural Science Foundation of China(No.51925506),and the XPLORER PRIZE.
文摘1-(4-ethylphenyl)-nonane-1,3-dione(0206)is an oil-soluble liquid molecule with rod-like structure.In this study,the chelate(0206-Fe)with octahedral structure was prepared by the reaction of ferric chloride and 1,3-diketone.The experimental results show that when using 0206 and a mixed solution containing 60%0206-Fe and 40%0206(0206-Fe(60%))as lubricants of the steel friction pairs,superlubricity can be achieved(0.007,0.006).But their wear scar diameters(WSD)were very large(532µm,370µm),which resulted in the pressure of only 44.3 and 61.8 MPa in the contact areas of the friction pairs.When 0206-Fe(60%)was mixed with PAO6,it was found that the friction coefficient(COF)decreased with increase of 0206-Fe(60%)in the solution.When the ratio of 0206-Fe(60%)to PAO6 was 8:2(PAO6(20%)),it exhibited better comprehensive tribological properties(232.3 MPa).Subsequent studies have shown that reducing the viscosity of the base oil in the mixed solution helped to reduce COF and increased WSD.Considering the COF,contact pressure,and running-in time,it was found that the mixed lubricant(Oil3(20%))prepared by the base oil with a viscosity of 19.7 mPa·s(Oil3)and 0206-Fe(60%)exhibited the best tribological properties(0.007,161.4 MPa,3,100 s).
基金supported by the Deanship of Research Oversight and Coordination(DROC)at King Fahd University of Petroleum and Minerals(KFUPM)in terms of Research Grant#DF191027.
文摘In this study,a spent palm cooking oil-based mud with an excellent H_(2)S scavenging capability induced by the inclusion of a small quantity of potassium permanganate is formulated and tested for the first time.The mud formulation,containing the spent palm oil as the continuous phase and water as the dispersed phase,respectively,was stabilized by Span 80 and rhamnolipid biosurfactant as primary and secondary emulsifiers,respectively,while hydrophobic zinc nanoparticles(NPs)were used as weighting agent.The results showed that H_(2)S scavenging capacity at the breakthrough time reached 182.4 g H_(2)S/barrel mud,which increased to 417.9 g H_(2)S/barrel mud at the saturation time,demonstrating the effective H_(2)S scavenging performance of the formulated mud.The spent palm oil-based mud(SPOBM)also showed a good flow behavior that could be well fitted using the Herschel-Bulkley and Casson models.The effect of temperature on the apparent viscosity of the SPOBM has been investigated,and the fitting of the viscosity-temperature data provided an estimate of the activation energy as 23.53 kJ/mol.The findings reported in this article reveal the feasibility of transforming the spent/waste cooking oils into a valuable commodity for formulating greener drilling fluids with acceptable rheology and excellent H_(2)S scavenging performance.
基金supported by the Postdoctoral Program of PetroChina Southwest Oil&Gas Field Company (Grant No.20220302-21).
文摘Natural gas is easily soluble in oil-based muds(OBM),leading to complex flow behavior in wellbores,especially in horizontal wells.In this study,a new transient flow model considering wellbore-formation coupling and gas solubility on flow behavior is developed to simulate gas kicks during horizontal drilling with OBM.Furthermore,the effect of gas solubility on parameters such as bottom-hole pressure(BHP),gas void fraction and mixture velocity in the flow behavior is analyzed.Finally,several critical factors affecting flow behavior are investigated and compared to gas kicks in water-based muds(WBM)where the effect of solubility is neglected.The results show that the invading gas exists as dissolved gas in the OBM and as free gas in the WBM.Before the gas escapes from the OBM,the pit gain is zero and there is barely any change in the BHP,annulus return flow rate and mixture velocity,which means that detecting gas kicks through these warning signs can be challenging until they get very close to the surface and develop rapidly.However,in WBM drilling,these parameters change quickly with the increasing gas kick time.Additionally,for both cases,the longer the horizontal length and the greater reservoir permeability,the greater the decrease in BHP,and the shorter the time for gas to migrate from the bottom-hole to the wellhead.A larger flow rate contributes to a greater initial BHP and a lesser BHP reduction.This research is of value in characterizing gas kick behavior and identifying novel ways for early gas kick detection during horizontal drilling with OBM.
基金Supported by the National Natural Science Foundation of China(21466016,21577053)the Natural Science Foundation of Yunnan Province(2016FB024).
文摘A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based fragrance was pre-encapsulated by an inner polyacrylate membrane via solvent evaporation,followed by in situ polymerization of MF precondensates as an outer shell.The polyacrylate membrane is used as an intermediate bridging layer to stabilize the oil-based fragrance,and to provide driving forces for in situ polymerization of MF precondensates through electrostatic attractions between carboxyl groups and ammonium ions.It was demonstrated that MF microcapsules containing clove oil were prepared successfully.The amount and the composition of the intermediate polyacrylate bridging layer were critical.Smooth and sphere-shaped MF-clove oil microcapsules were prepared when the weight ratio of polyacrylate to clove oil was over 60 wt%and the concentration of acrylic acid(AA)increased to 10 wt%in polyacrylate.In addition,MF microcapsules containing sunflower oil and hexyl salicylate were prepared by using this method.The work suggests that this new approach can be potentially used to encapsulate various core materials,tuning the shell properties of microcapsules such as thickness,mechanical strength and release properties.
基金Project(50574061) supported by the National Natural Science Foundation of ChinaProject(IRT0411) supported by the Changjiang Scholars and Innovative Research Team,Ministry of Education
文摘The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.
基金Supported by the Ministry of Higher Education(MOHE)Universiti Teknologi Malaysia(RU Research GrantGUP:Q.J130000.2546.12H50)
文摘Phenol is considered as pollutant due to its toxicity and carcinogenic effect.Thus,variety of innovative methods for separation and recovery of phenolic compounds is developed in order to remove the unwanted phenol from wastewater and obtain valuable phenolic compound.One of potential method is extraction using green based liquid organic solvent.Therefore,the feasibility of using palm oil was investigated.In this research,palm oil based organic phase was used as diluents to treat a simulated wastewater containing 300×10^(-6) of phenol solution using emulsion liquid membrane process(ELM).The stability of water-in-oil(W/O) emulsion on diluent composition and the parameters affecting the phenol removal efficiency and stability of the emulsion;such as emulsification speed,emulsification time,agitation speed,surfactant concentration,pH of external phase,contact time,stripping agent concentration and treat ratio were carried out.The results of ELM study showed that at ratio7 to 3 of palm oil to kerosene,5 min and 1300 r·min^(-1) of emulsification process the stabile primary emulsion were formed.Also,no carrier is needed to facilitate the phenol extraction.In experimental conditions of500 r·min^(-1) of agitation speed,3%Span 80,pH 8 of external phase,5 min of contact time,0.1 mol·L^(-1) NaOH as stripping agent and 1:10 of treat ratio,the ELM process was very promising for removing the phenol from the wastewater.The extraction performance at about 83%of phenol was removed for simulated wastewater and an enrichment of phenol in recovery phase as phenolate compound was around 11 times.
基金Funded by National Natural Science Foundation of China(No.51475454)National Natural Science Foundation of JiangsuProvince(No.BK20151144)+1 种基金Fundamental Research Funds forthe Central Universities(No.2014QNA38)Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)
文摘In order to study the squeeze-strengthening effect of silicone oil-based magnetorheological fluid （MRF）, theoretical basis of disc squeezing brake was presented and a squeezing braking characteristics test-bed for MRF was designed. Moreover, relevant experiments were carded out and the relationship between squeezing pressure and braking torque was proposed. Experiments results showed that the yield stress of MRF improved linearly with the increasing of external squeezing pressure and the braking torque increased three times when external squeezing pressure achieved 2 MPa.
