Nb-Tihot-rolled TRIP-assisted steel with high plasticity and appropriate volume percentage of retained austenite based on fine ferrite grain have been developed in the experiment. The test results showed that niobium ...Nb-Tihot-rolled TRIP-assisted steel with high plasticity and appropriate volume percentage of retained austenite based on fine ferrite grain have been developed in the experiment. The test results showed that niobium tend to exist in solution state in matrix with less precipitation, and niobium-titanium could be precipitated in form of （Nb, Ti）C or （Nb, Ti） （C, N）, which play an important role in increasing yield strength （from 495 MPa to 610 MPa）. Besides, the retained austenite had a positive effect on improving the plasticity by transformation into martensite during tensile deformation.展开更多
The mechanical peratures and cooling rates properties and microstructure of as-cast Nb-Ti microalloyed steel at different tern- are investigated in this paper. The III brittle zone （700--900~C） is revealed. The redu...The mechanical peratures and cooling rates properties and microstructure of as-cast Nb-Ti microalloyed steel at different tern- are investigated in this paper. The III brittle zone （700--900~C） is revealed. The reduction of the hot ductility is due to the film-like proeutectoid ferrite or the Nb（C, N） precipitates along the austenitic grain boundaries. In the temperature range of 850 1000~C, with the increase of the cooling rate, the hot ductility decreases. However, in the range of 650--850 ~C, the appearance of large volume fractions of ferrite on austenite grain boundaries minimizes the effect of cooling rate on hot ductility. When the cooling rate is 10 ℃/s, austenite transforms more quickly to ferrite and at a lower temperature a larger amount of ferrite nucleates and precipitates in the grain, which leads to a sharper improvement in the hot ductility at 650 ℃.展开更多
通过90t EBT电弧炉-100 t LF+VD-喂丝-Φ20mm CC流程开发了Nb-Ti微合金化海底管线管钢HSL450S(%:0.06C、0.40Cr、0.15Mo、0.02Ti、0.05Nb)。经30炉分析得出,[O]为35.2×10^(-6),[N]为78.8×10^(-6)。该钢的组织为回火贝氏体-珠...通过90t EBT电弧炉-100 t LF+VD-喂丝-Φ20mm CC流程开发了Nb-Ti微合金化海底管线管钢HSL450S(%:0.06C、0.40Cr、0.15Mo、0.02Ti、0.05Nb)。经30炉分析得出,[O]为35.2×10^(-6),[N]为78.8×10^(-6)。该钢的组织为回火贝氏体-珠光体+多边形铁素体。轧制的Φ102mm×14mm和Φ168.3mm×8.7mm HSL450S钢管的晶粒度为10～11级,机械性能满足海底管线管X60、X65钢级标准要求。展开更多
In situ measurements of austenite grain growth were made at various temperatures in the range of 1273-1473 K with subsequent isothermal holding time of 3600 s for the Nb-Ti-bearing and Nb-Ti-free high carb on steel by...In situ measurements of austenite grain growth were made at various temperatures in the range of 1273-1473 K with subsequent isothermal holding time of 3600 s for the Nb-Ti-bearing and Nb-Ti-free high carb on steel by using a confocal laser scanning microscope.The solid solute behavior of Nb-Ti carbides during austenitizing process was analyzed.The experimental results indicate that the austenite grains of both steels grow up gradually with increasing the heating temperature and holding time;the size and growth rate of austenite grain of Nb-Ti-bearing high carbon steel are much lower than those of Nb-Ti-free high carbon steel.A large amount of(Nb,Ti)(C,N)nanoparticles are observed in Nb-Tibearing steel,which retain the strong pinning effect on austenite grain boundary.The kinetics model of austenite grain growth of Nb-Ti-bearing steel during isothermal heat treatment is obtained and the predicted values calculated by using the model meet the experimental values very well.展开更多
文摘Nb-Tihot-rolled TRIP-assisted steel with high plasticity and appropriate volume percentage of retained austenite based on fine ferrite grain have been developed in the experiment. The test results showed that niobium tend to exist in solution state in matrix with less precipitation, and niobium-titanium could be precipitated in form of （Nb, Ti）C or （Nb, Ti） （C, N）, which play an important role in increasing yield strength （from 495 MPa to 610 MPa）. Besides, the retained austenite had a positive effect on improving the plasticity by transformation into martensite during tensile deformation.
文摘The mechanical peratures and cooling rates properties and microstructure of as-cast Nb-Ti microalloyed steel at different tern- are investigated in this paper. The III brittle zone （700--900~C） is revealed. The reduction of the hot ductility is due to the film-like proeutectoid ferrite or the Nb（C, N） precipitates along the austenitic grain boundaries. In the temperature range of 850 1000~C, with the increase of the cooling rate, the hot ductility decreases. However, in the range of 650--850 ~C, the appearance of large volume fractions of ferrite on austenite grain boundaries minimizes the effect of cooling rate on hot ductility. When the cooling rate is 10 ℃/s, austenite transforms more quickly to ferrite and at a lower temperature a larger amount of ferrite nucleates and precipitates in the grain, which leads to a sharper improvement in the hot ductility at 650 ℃.
文摘In situ measurements of austenite grain growth were made at various temperatures in the range of 1273-1473 K with subsequent isothermal holding time of 3600 s for the Nb-Ti-bearing and Nb-Ti-free high carb on steel by using a confocal laser scanning microscope.The solid solute behavior of Nb-Ti carbides during austenitizing process was analyzed.The experimental results indicate that the austenite grains of both steels grow up gradually with increasing the heating temperature and holding time;the size and growth rate of austenite grain of Nb-Ti-bearing high carbon steel are much lower than those of Nb-Ti-free high carbon steel.A large amount of(Nb,Ti)(C,N)nanoparticles are observed in Nb-Tibearing steel,which retain the strong pinning effect on austenite grain boundary.The kinetics model of austenite grain growth of Nb-Ti-bearing steel during isothermal heat treatment is obtained and the predicted values calculated by using the model meet the experimental values very well.
