Gas-liquid two-phase flow occurs increasingly in some dynamic devices operating in the oceanic condition. The relative data are limited with respect to flow characteristics, so the present study is to investigate syst...Gas-liquid two-phase flow occurs increasingly in some dynamic devices operating in the oceanic condition. The relative data are limited with respect to flow characteristics, so the present study is to investigate systematically single-phase pressure drop, and to develop the theory for frictional factor under the roiling condition. Using deionized water as the test fluid, a series of experiments of single-phase flow were conducted in pipe with the inner diameter of 34.5 ram. The test section was horizontally settled on the rolling apparatus, and its regularity was similar to simple harmonic motion. It is found that the pressure drop during rolling motion fluctuate with the change of the rolling period and rolling angle, which is significantly different from fluid motion in a steady state. By the contrast between experiment results and stable-state theory values, existing correlations can not predict present frictional factor very well. Therefore, in the present article, the single-phase frictional factor is correlated with the Reynolds number for rolling motion, and its computated results agree well with experimental data.展开更多
The rolling bearing friction torque which is characterized by its uncertainty and nonlinearity affects heavily the dynamic performance of a system such as missiles, spacecrafts and radars, etc. It is difficult to use ...The rolling bearing friction torque which is characterized by its uncertainty and nonlinearity affects heavily the dynamic performance of a system such as missiles, spacecrafts and radars, etc. It is difficult to use the classical statistical theory to evaluate the dynamic evaluation of the rolling bearing friction torque for the lack of prior information about both probability distribution and trends. For this reason, based on the information poor system theory and combined with the correlation dimension in chaos theory, the concepts about the mean of the dynamic fluctuant range （MDFR） and the grey relation are proposed to resolve the problem about evaluating the nonlinear characteristic and the dynamic uncertainty of the rolling bearing friction torque. Friction torque experiments are done for three types of the rolling bearings marked with HKTA, HKTB and HKTC separately; meantime, the correlation dimension and MDFR are calculated to describe the nonlinear characteristic and the dynamic uncertainty of the friction torque, respectively. And the experiments reveal that there is a certain grey relation between the nonlinear characteristic and the dynamic uncertainty of the rolling bearing friction torque, viz. MDFR will become the nonlinear increasing trend with the correlation dimension increasing. Under the condition of fewer characteristic data and the lack of prior information about both probability distribution and trends, the unitive evaluation for the nonlinear characteristic and the dynamic uncertainty of the rolling bearing friction torque is realized with the grey confidence level of 87.7%-96.3%.展开更多
In the last few years,substantial experimental simulation and mumerical modelling hare been carried out in IMMPETUS to characterise the interfacial heat transfer and friction conditions during hot forging and rolling ...In the last few years,substantial experimental simulation and mumerical modelling hare been carried out in IMMPETUS to characterise the interfacial heat transfer and friction conditions during hot forging and rolling of steels. Emphasis has been placed on the influence of the oxide scale which forms on the steel workpiece. In the present paper, the experimental methods used for investigating interfacial heat transfer and friction conditions are described. Theses include hot flat rolling of steel slabs and hot axi- symmetric forging of steel cylinders and rings.Temperature measurements and computations demon- strate that for similar conditions, similar conditions, the effective interfacial heat transfer coefficients (IHTC) derived for hot rolling are significantly higher than those for forging, mainly due to the contribution of scale cracking during rolling. On the basis of experimental observations and numerical analysis,physical models for interfacial heat transfer in forging and rolling have been established. In addition, hot' sandwich' rolling and hot tensile tests with finite element modelling have been carried out to evaluate the hot ductility of the oxide scale.The results indicate that the defomation, cracking and decohesion behaviour of the oxide scale depend on deformation temperature, strain and relative strengths of the scale layer and scale - steel interface.Finaly, friction results from hot ring compression tests and from hot rolling with forward/backward slip measurements are reported.展开更多
A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream su...A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.展开更多
The discrete element method(DEM)has become a valuable tool for understanding the mechanical behaviour of granular assemblies,however,the accuracy of the DEM simulations depends on several interaction parameters such a...The discrete element method(DEM)has become a valuable tool for understanding the mechanical behaviour of granular assemblies,however,the accuracy of the DEM simulations depends on several interaction parameters such as the sliding friction and rolling friction coefficients.Generally,these parameters are estimated using bulk calibration approach(BCA)where the draw down test has been suggested as an effective way to approach these coefficients.This test provides up to four bulk criteria,the angle of repose,shear angle,mass flow rate and the mass loss which are used to narrow down the possible coefficients.However,there is still more research needed around it to fully understand how this methodology works.An experimental and numerical study was carried out using the draw down test to assess the influence of different mass flow rates and particle shapes on DEM parameters for a cohesionless bulk material.It is concluded that use of multi-sphere particles and three aperture sizes in the draw down test to calibrate the sliding and rolling friction parameters of a cohesionless bulk material can converge to a small feasible region in which a single combination of the friction coefficients can be selected.The calibrated sliding and rolling friction coefficients were validated using multi-sphere particles,where the maximum deviation was 5.9%from the experimental values.展开更多
基金supported by the National Natural Science Foundation of China (Grant No.50376012)supported by the Scientific Research Foundation of Harbin Engineering University (Grant No.HEUFT07066)
文摘Gas-liquid two-phase flow occurs increasingly in some dynamic devices operating in the oceanic condition. The relative data are limited with respect to flow characteristics, so the present study is to investigate systematically single-phase pressure drop, and to develop the theory for frictional factor under the roiling condition. Using deionized water as the test fluid, a series of experiments of single-phase flow were conducted in pipe with the inner diameter of 34.5 ram. The test section was horizontally settled on the rolling apparatus, and its regularity was similar to simple harmonic motion. It is found that the pressure drop during rolling motion fluctuate with the change of the rolling period and rolling angle, which is significantly different from fluid motion in a steady state. By the contrast between experiment results and stable-state theory values, existing correlations can not predict present frictional factor very well. Therefore, in the present article, the single-phase frictional factor is correlated with the Reynolds number for rolling motion, and its computated results agree well with experimental data.
基金supported by National Natural Science Foundation of China (Grant No. 50675011)Doctoral Scientific Research Enabling Foundation of Henan University of Science and Technology,China (Grant No. 09001318)
文摘The rolling bearing friction torque which is characterized by its uncertainty and nonlinearity affects heavily the dynamic performance of a system such as missiles, spacecrafts and radars, etc. It is difficult to use the classical statistical theory to evaluate the dynamic evaluation of the rolling bearing friction torque for the lack of prior information about both probability distribution and trends. For this reason, based on the information poor system theory and combined with the correlation dimension in chaos theory, the concepts about the mean of the dynamic fluctuant range （MDFR） and the grey relation are proposed to resolve the problem about evaluating the nonlinear characteristic and the dynamic uncertainty of the rolling bearing friction torque. Friction torque experiments are done for three types of the rolling bearings marked with HKTA, HKTB and HKTC separately; meantime, the correlation dimension and MDFR are calculated to describe the nonlinear characteristic and the dynamic uncertainty of the friction torque, respectively. And the experiments reveal that there is a certain grey relation between the nonlinear characteristic and the dynamic uncertainty of the rolling bearing friction torque, viz. MDFR will become the nonlinear increasing trend with the correlation dimension increasing. Under the condition of fewer characteristic data and the lack of prior information about both probability distribution and trends, the unitive evaluation for the nonlinear characteristic and the dynamic uncertainty of the rolling bearing friction torque is realized with the grey confidence level of 87.7%-96.3%.
文摘In the last few years,substantial experimental simulation and mumerical modelling hare been carried out in IMMPETUS to characterise the interfacial heat transfer and friction conditions during hot forging and rolling of steels. Emphasis has been placed on the influence of the oxide scale which forms on the steel workpiece. In the present paper, the experimental methods used for investigating interfacial heat transfer and friction conditions are described. Theses include hot flat rolling of steel slabs and hot axi- symmetric forging of steel cylinders and rings.Temperature measurements and computations demon- strate that for similar conditions, similar conditions, the effective interfacial heat transfer coefficients (IHTC) derived for hot rolling are significantly higher than those for forging, mainly due to the contribution of scale cracking during rolling. On the basis of experimental observations and numerical analysis,physical models for interfacial heat transfer in forging and rolling have been established. In addition, hot' sandwich' rolling and hot tensile tests with finite element modelling have been carried out to evaluate the hot ductility of the oxide scale.The results indicate that the defomation, cracking and decohesion behaviour of the oxide scale depend on deformation temperature, strain and relative strengths of the scale layer and scale - steel interface.Finaly, friction results from hot ring compression tests and from hot rolling with forward/backward slip measurements are reported.
基金Sponsored by National Natural Science Foundation of China(50175095)Provincial Natural Science Foundation of Hebei of China(502173)
文摘A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.
基金Weir Group project reference 21/1/ESCO/AM&D/1051。
文摘The discrete element method(DEM)has become a valuable tool for understanding the mechanical behaviour of granular assemblies,however,the accuracy of the DEM simulations depends on several interaction parameters such as the sliding friction and rolling friction coefficients.Generally,these parameters are estimated using bulk calibration approach(BCA)where the draw down test has been suggested as an effective way to approach these coefficients.This test provides up to four bulk criteria,the angle of repose,shear angle,mass flow rate and the mass loss which are used to narrow down the possible coefficients.However,there is still more research needed around it to fully understand how this methodology works.An experimental and numerical study was carried out using the draw down test to assess the influence of different mass flow rates and particle shapes on DEM parameters for a cohesionless bulk material.It is concluded that use of multi-sphere particles and three aperture sizes in the draw down test to calibrate the sliding and rolling friction parameters of a cohesionless bulk material can converge to a small feasible region in which a single combination of the friction coefficients can be selected.The calibrated sliding and rolling friction coefficients were validated using multi-sphere particles,where the maximum deviation was 5.9%from the experimental values.
