澳大利亚联邦科学与工业研究组织的全称为Commonwealth Scientific and Industrial Research Organization,简称为CSIRO。它是澳大利亚最大的科学研究机构,在世界上也很著名,一提起CSIRO,人们就会知道。该组织相当于中国科学院及中国农...澳大利亚联邦科学与工业研究组织的全称为Commonwealth Scientific and Industrial Research Organization,简称为CSIRO。它是澳大利亚最大的科学研究机构,在世界上也很著名,一提起CSIRO,人们就会知道。该组织相当于中国科学院及中国农业科学院的综合研究机构,以应用科学技术著称。它的前身为澳科学与工业研究理事会(Council for Sci-展开更多
Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR-RCS) and a high pressure die casting machine was successfully performed on Al-5Ti-1B grain refined aluminum a...Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR-RCS) and a high pressure die casting machine was successfully performed on Al-5Ti-1B grain refined aluminum alloy 7075.Grain refinement levels used were 0.03% Ti,0.13% Ti and 0.29% Ti(mass fraction).Tensile tests reveal that the ultimate tensile strengths,at all levels of grain refinement,are at least 97% of the specified minimum.Elongation at fracture increases with the increase of level of grain refinement although a maximum elongation is only 76% of the required minimum elongation in the case of 0.29% Ti.Incipient melting,during solution treatment,of the low melting point multinary eutectic causes porosity in the material and accounts for poor elongation results.0.03% Ti has a coarse eutectic structure forming larger pores while 0.29% Ti has a fine structure forming fine pores in the multinary eutectic.The 0.2% offset yield strengths of all the grain refinement levels are at least equal to or above the specified minimum and a decrease is observed with the increase of grain refinement level.There is a clear reduction in grain size from 0.03% Ti to 0.29% Ti in the as-cast condition.An underlying grain structure develops in the T6 condition material which has an inverse size to the as-cast structure;coarse grained as-cast material results in fine grained T6 condition material after solution heat treatment.The decrease in the offset yield strength as grain refinement increases correlates very strongly with the T6 grain sizes according to a Hall-Petch type relationship.展开更多
Rheocasting of plates in Al alloy 359 reinforced with SiC at 11%,27% and 50%(volume fractions) exhibits the capability of the council for scientific and industrial research-rheocasting system(CSIR-RCS) in rheo-process...Rheocasting of plates in Al alloy 359 reinforced with SiC at 11%,27% and 50%(volume fractions) exhibits the capability of the council for scientific and industrial research-rheocasting system(CSIR-RCS) in rheo-processing and high pressure die casting of SiC metal matrix composites.The metal matrix consisting of nearly spherical proeutectic α(Al) globules was produced.Spheroidization of fibrous eutectic silicon took place upon heat treatment of the as-cast metal matrix composites(MMCs).Hardness increases as the volume fractions of SiC increases.Wear rates of the MMCs in the F and T6 heat treatment conditions were assessed with a metallographic preparation machine.It is found that the 11% SiC MMC wear rate is higher on SiC abrasives compared with the 50% SiC MMC wear rate due to wear of the aluminum matrix.This trend is reversed on diamond abrasives due to pull-out of the irregular shaped composite particles.The 50% SiC MMC suffers from composite particle fracture porosity after high pressure die casting(HPDC).展开更多
文摘澳大利亚联邦科学与工业研究组织的全称为Commonwealth Scientific and Industrial Research Organization,简称为CSIRO。它是澳大利亚最大的科学研究机构,在世界上也很著名,一提起CSIRO,人们就会知道。该组织相当于中国科学院及中国农业科学院的综合研究机构,以应用科学技术著称。它的前身为澳科学与工业研究理事会(Council for Sci-
文摘Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR-RCS) and a high pressure die casting machine was successfully performed on Al-5Ti-1B grain refined aluminum alloy 7075.Grain refinement levels used were 0.03% Ti,0.13% Ti and 0.29% Ti(mass fraction).Tensile tests reveal that the ultimate tensile strengths,at all levels of grain refinement,are at least 97% of the specified minimum.Elongation at fracture increases with the increase of level of grain refinement although a maximum elongation is only 76% of the required minimum elongation in the case of 0.29% Ti.Incipient melting,during solution treatment,of the low melting point multinary eutectic causes porosity in the material and accounts for poor elongation results.0.03% Ti has a coarse eutectic structure forming larger pores while 0.29% Ti has a fine structure forming fine pores in the multinary eutectic.The 0.2% offset yield strengths of all the grain refinement levels are at least equal to or above the specified minimum and a decrease is observed with the increase of grain refinement level.There is a clear reduction in grain size from 0.03% Ti to 0.29% Ti in the as-cast condition.An underlying grain structure develops in the T6 condition material which has an inverse size to the as-cast structure;coarse grained as-cast material results in fine grained T6 condition material after solution heat treatment.The decrease in the offset yield strength as grain refinement increases correlates very strongly with the T6 grain sizes according to a Hall-Petch type relationship.
文摘Rheocasting of plates in Al alloy 359 reinforced with SiC at 11%,27% and 50%(volume fractions) exhibits the capability of the council for scientific and industrial research-rheocasting system(CSIR-RCS) in rheo-processing and high pressure die casting of SiC metal matrix composites.The metal matrix consisting of nearly spherical proeutectic α(Al) globules was produced.Spheroidization of fibrous eutectic silicon took place upon heat treatment of the as-cast metal matrix composites(MMCs).Hardness increases as the volume fractions of SiC increases.Wear rates of the MMCs in the F and T6 heat treatment conditions were assessed with a metallographic preparation machine.It is found that the 11% SiC MMC wear rate is higher on SiC abrasives compared with the 50% SiC MMC wear rate due to wear of the aluminum matrix.This trend is reversed on diamond abrasives due to pull-out of the irregular shaped composite particles.The 50% SiC MMC suffers from composite particle fracture porosity after high pressure die casting(HPDC).
