To investigate the effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg （A357） alloy, some novel Al-7.0Si-0.55Mg alloys added with different amount of Al-STi-1B-RE grain...To investigate the effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg （A357） alloy, some novel Al-7.0Si-0.55Mg alloys added with different amount of Al-STi-1B-RE grain refiner with different RE composition were prepared by vacuum-melting. The microstructure and fracture behavior of the AI-7.0Si-0.55Mg alloys with the grain refiners were observed by X-ray diffraction （XRD）, optical microscopy （OM）, scanning electron microscopy （SEM）, and the mechanical properties of the alloys were tested in mechanical testing machine at room temperature. The observation of AI-Ti-B-RE morphology and internal structure of the particles reveals that it exhibits a TiAl3/Ti2Al20RE core-shell structure via heterogeneous TiB2 nuclei. The tensile strength of Al-7.0Si-0.55Mg alloys with Al-5Ti-1B-3.0RE grain refiner reaches the peak value at the same addition （0.2%） of grain refiner.展开更多
Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR-RCS) and a high pressure die casting machine was successfully performed on Al-5Ti-1B grain refined aluminum a...Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR-RCS) and a high pressure die casting machine was successfully performed on Al-5Ti-1B grain refined aluminum alloy 7075.Grain refinement levels used were 0.03% Ti,0.13% Ti and 0.29% Ti(mass fraction).Tensile tests reveal that the ultimate tensile strengths,at all levels of grain refinement,are at least 97% of the specified minimum.Elongation at fracture increases with the increase of level of grain refinement although a maximum elongation is only 76% of the required minimum elongation in the case of 0.29% Ti.Incipient melting,during solution treatment,of the low melting point multinary eutectic causes porosity in the material and accounts for poor elongation results.0.03% Ti has a coarse eutectic structure forming larger pores while 0.29% Ti has a fine structure forming fine pores in the multinary eutectic.The 0.2% offset yield strengths of all the grain refinement levels are at least equal to or above the specified minimum and a decrease is observed with the increase of grain refinement level.There is a clear reduction in grain size from 0.03% Ti to 0.29% Ti in the as-cast condition.An underlying grain structure develops in the T6 condition material which has an inverse size to the as-cast structure;coarse grained as-cast material results in fine grained T6 condition material after solution heat treatment.The decrease in the offset yield strength as grain refinement increases correlates very strongly with the T6 grain sizes according to a Hall-Petch type relationship.展开更多
The effect of boron content on grain refinement of commercially pure aluminum by Al-5Ti-1B was quantitatively assessed.When the boron content is less than 0.03 wt.%,the refining performance of Al-5Ti-1B gradually is w...The effect of boron content on grain refinement of commercially pure aluminum by Al-5Ti-1B was quantitatively assessed.When the boron content is less than 0.03 wt.%,the refining performance of Al-5Ti-1B gradually is weakened as the boron content increases,which is attributed to the reaction of boron with the Al_(3)Ti interlayer on TiB_(2)and the consumption of solute Ti.On the contrary,when the boron content exceeds 0.03 wt.%,the refining performance of Al-5Ti-1B gradually recovers with increasing boron content,which is related to the formation of primary AlB_(2)particles that provide additional nucleant substrates.展开更多
The isothermal compression tests of A1-5Ti- 1B master alloy were conducted on the thermal mechanical simulator Gleeble-1500D at the deformation temperature range of 300-450 ℃,the strain rate range of 0.01- 10.00 s^-l...The isothermal compression tests of A1-5Ti- 1B master alloy were conducted on the thermal mechanical simulator Gleeble-1500D at the deformation temperature range of 300-450 ℃,the strain rate range of 0.01- 10.00 s^-l, and the engineering strain of 50 %. The effects of deformation temperatures and strain rates on the flow stress were analyzed by the true stress-true strain curves. The result indicates that the flow stress increases with the increase of strain rate, while it decreases with the increase of temperature. The hot deformation activation energy of A1-5Ti-IB master alloy is calculated to be 250.9 kJ.mol^-1, and the constitutive equation is established as ε=1.97 x lO^19[sinh（O.O15δ）^11.14exp（-250.9/RT）, and the validity of this constitutive equation is verified. Based on dynamic material model （DMM） criterion, the hot processing map of AI-5Ti-1B master alloy is obtained. The optimum hot extrusion conditions are determined as deformation temperature of 400℃ and strain rate of 1.00 s^-1, and the flow instability only appears at the temperature range of 300-340℃ at the base of the hot processing map.展开更多
基金Project(2012CB619503)supported by the Natioanl Basic Research Program of ChinaProject(2013AA031001)supported by the National High-tech Research and Development Program of ChinaProject(2012DFA50630)supported by the International Science&Technology Cooperation Program of China
文摘To investigate the effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg （A357） alloy, some novel Al-7.0Si-0.55Mg alloys added with different amount of Al-STi-1B-RE grain refiner with different RE composition were prepared by vacuum-melting. The microstructure and fracture behavior of the AI-7.0Si-0.55Mg alloys with the grain refiners were observed by X-ray diffraction （XRD）, optical microscopy （OM）, scanning electron microscopy （SEM）, and the mechanical properties of the alloys were tested in mechanical testing machine at room temperature. The observation of AI-Ti-B-RE morphology and internal structure of the particles reveals that it exhibits a TiAl3/Ti2Al20RE core-shell structure via heterogeneous TiB2 nuclei. The tensile strength of Al-7.0Si-0.55Mg alloys with Al-5Ti-1B-3.0RE grain refiner reaches the peak value at the same addition （0.2%） of grain refiner.
文摘Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR-RCS) and a high pressure die casting machine was successfully performed on Al-5Ti-1B grain refined aluminum alloy 7075.Grain refinement levels used were 0.03% Ti,0.13% Ti and 0.29% Ti(mass fraction).Tensile tests reveal that the ultimate tensile strengths,at all levels of grain refinement,are at least 97% of the specified minimum.Elongation at fracture increases with the increase of level of grain refinement although a maximum elongation is only 76% of the required minimum elongation in the case of 0.29% Ti.Incipient melting,during solution treatment,of the low melting point multinary eutectic causes porosity in the material and accounts for poor elongation results.0.03% Ti has a coarse eutectic structure forming larger pores while 0.29% Ti has a fine structure forming fine pores in the multinary eutectic.The 0.2% offset yield strengths of all the grain refinement levels are at least equal to or above the specified minimum and a decrease is observed with the increase of grain refinement level.There is a clear reduction in grain size from 0.03% Ti to 0.29% Ti in the as-cast condition.An underlying grain structure develops in the T6 condition material which has an inverse size to the as-cast structure;coarse grained as-cast material results in fine grained T6 condition material after solution heat treatment.The decrease in the offset yield strength as grain refinement increases correlates very strongly with the T6 grain sizes according to a Hall-Petch type relationship.
基金the financial supports from the National Natural Science Foundation of China(Nos.U1832183,52090042,51821001)。
文摘The effect of boron content on grain refinement of commercially pure aluminum by Al-5Ti-1B was quantitatively assessed.When the boron content is less than 0.03 wt.%,the refining performance of Al-5Ti-1B gradually is weakened as the boron content increases,which is attributed to the reaction of boron with the Al_(3)Ti interlayer on TiB_(2)and the consumption of solute Ti.On the contrary,when the boron content exceeds 0.03 wt.%,the refining performance of Al-5Ti-1B gradually recovers with increasing boron content,which is related to the formation of primary AlB_(2)particles that provide additional nucleant substrates.
基金financially supported by the Natural Science Foundation of Heilongjiang Province(No.E201107)
文摘The isothermal compression tests of A1-5Ti- 1B master alloy were conducted on the thermal mechanical simulator Gleeble-1500D at the deformation temperature range of 300-450 ℃,the strain rate range of 0.01- 10.00 s^-l, and the engineering strain of 50 %. The effects of deformation temperatures and strain rates on the flow stress were analyzed by the true stress-true strain curves. The result indicates that the flow stress increases with the increase of strain rate, while it decreases with the increase of temperature. The hot deformation activation energy of A1-5Ti-IB master alloy is calculated to be 250.9 kJ.mol^-1, and the constitutive equation is established as ε=1.97 x lO^19[sinh（O.O15δ）^11.14exp（-250.9/RT）, and the validity of this constitutive equation is verified. Based on dynamic material model （DMM） criterion, the hot processing map of AI-5Ti-1B master alloy is obtained. The optimum hot extrusion conditions are determined as deformation temperature of 400℃ and strain rate of 1.00 s^-1, and the flow instability only appears at the temperature range of 300-340℃ at the base of the hot processing map.
