The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature ra...The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature range of 500-570 ℃ and a strain rate range of 4.17×10^-4 s-1^- 1×10^- 2 s^- 1. Maximum tensile elongation 530% was obtained at 550 ℃ and strain rate ε＆ =4 .17×10^-4 s^-1. Dislocations were observed in grain interiors and at grain boundaries during uniaxial tensile deformation by transmission electronic microscopy （TEM）, respectively. Results show that the grain boundary sliding （GBS） accommodated by dislocation motion is the principal reason for superplastic deformation. The cavities and fracture were observed during uniaxial tensile deformation of the alloy by scanning electronic microscopy （SEM）, indicating that linkage of cavities in large region would induce failure of the material. Moreover, presence of liquid phase at grain boundary also affects the superplastic deformation and behavior of cavities.展开更多
The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 1...The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 10^-4- 1.0× 10^-2 s^-1. The maximum elongation 530% of the fine-grained 5083 AI alloy was obtained at 550℃ and 4.17× 10^-4 s^-1. Fracture analysis by scanning electron microscopy （SEM） indicated that the formation of filament （formed by liquid phase） was greatly affected by the tensile temperature and strain rate. The results also showed that the optimum morphology of formed filament was obtained at 550℃ and a strain rate of 4.17× 10^-4 s^-1. The effect of liquid phase on superplastic deformation of the alloy was further discussed.展开更多
采用电化学方法研究了5083铝合金在海水中的腐蚀行为,考察了Cl-浓度对其点蚀行为的影响。结果表明,5083铝合金在海水中的点蚀击破电位为-690 m V,相对应的点蚀保护电位为-720 m V。Cl-是诱发5083铝合金发生点蚀的活性离子,对于同离子强...采用电化学方法研究了5083铝合金在海水中的腐蚀行为,考察了Cl-浓度对其点蚀行为的影响。结果表明,5083铝合金在海水中的点蚀击破电位为-690 m V,相对应的点蚀保护电位为-720 m V。Cl-是诱发5083铝合金发生点蚀的活性离子,对于同离子强度的溶液,Cl-含量在0~0.1 mol/kg时,点蚀击破电位随Cl-含量的升高快速下降,Cl-含量超过0.1 mol/kg时,点蚀击破电位不再发生明显变化。在此基础上,通过极化实验确定了5083铝合金在海水中适用的阴极保护电位范围为-800^-1000 m V。展开更多
Electrochemical tests were undertaken to determine the optimum conditions in seawater for corrosion protection of friction stir-welded 5083-O Al alloy.Polarization trend observations show that the limiting potential t...Electrochemical tests were undertaken to determine the optimum conditions in seawater for corrosion protection of friction stir-welded 5083-O Al alloy.Polarization trend observations show that the limiting potential that avoids the effects of hydrogen embrittlement is -1.6 V,corresponding to the crossover point between concentration polarization and activation polarization.However,the optimum protection potential is between -1.5 and -0.7 V since the current density at these values is low in the potentiostatic tests.When a galvanic cell is formed in the seawater,the welds exhibit electrochemically stable trends.Welded parts in galvanic tests with various area ratios are stable and have excellent anticorrosion characteristics.展开更多
The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average s...The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average size of 15 m and porosity in the range of 0.1 vol. % to 5vol. % . Two distinct TMP procedures are employed to close porosity and refine grain size:extrusion plus rolling and direct rolling. The material processed using the former method exhibits arelatively high superplasticity with a maximum superplastic elongation of 465 % , whereas thatprocessed using the latter method exhibits a maximum superplastic elongation of 295 % . Materialsprocessed using extrusion plus rolling and direct rolling both exhibit similar stress-strainbehavior and strain rate sensitivity factors. The strain rate factors are in the 0.3 to 0.5 range.The difference in their superplastic elongation is possibly the result of differences in grain sizeand available cavity nucleation sites provided by closed gas pores.展开更多
文摘The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature range of 500-570 ℃ and a strain rate range of 4.17×10^-4 s-1^- 1×10^- 2 s^- 1. Maximum tensile elongation 530% was obtained at 550 ℃ and strain rate ε＆ =4 .17×10^-4 s^-1. Dislocations were observed in grain interiors and at grain boundaries during uniaxial tensile deformation by transmission electronic microscopy （TEM）, respectively. Results show that the grain boundary sliding （GBS） accommodated by dislocation motion is the principal reason for superplastic deformation. The cavities and fracture were observed during uniaxial tensile deformation of the alloy by scanning electronic microscopy （SEM）, indicating that linkage of cavities in large region would induce failure of the material. Moreover, presence of liquid phase at grain boundary also affects the superplastic deformation and behavior of cavities.
文摘The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 10^-4- 1.0× 10^-2 s^-1. The maximum elongation 530% of the fine-grained 5083 AI alloy was obtained at 550℃ and 4.17× 10^-4 s^-1. Fracture analysis by scanning electron microscopy （SEM） indicated that the formation of filament （formed by liquid phase） was greatly affected by the tensile temperature and strain rate. The results also showed that the optimum morphology of formed filament was obtained at 550℃ and a strain rate of 4.17× 10^-4 s^-1. The effect of liquid phase on superplastic deformation of the alloy was further discussed.
文摘采用电化学方法研究了5083铝合金在海水中的腐蚀行为,考察了Cl-浓度对其点蚀行为的影响。结果表明,5083铝合金在海水中的点蚀击破电位为-690 m V,相对应的点蚀保护电位为-720 m V。Cl-是诱发5083铝合金发生点蚀的活性离子,对于同离子强度的溶液,Cl-含量在0~0.1 mol/kg时,点蚀击破电位随Cl-含量的升高快速下降,Cl-含量超过0.1 mol/kg时,点蚀击破电位不再发生明显变化。在此基础上,通过极化实验确定了5083铝合金在海水中适用的阴极保护电位范围为-800^-1000 m V。
基金The MEST and KOTEF through the Human Resource Training Project for Regional Innovation
文摘Electrochemical tests were undertaken to determine the optimum conditions in seawater for corrosion protection of friction stir-welded 5083-O Al alloy.Polarization trend observations show that the limiting potential that avoids the effects of hydrogen embrittlement is -1.6 V,corresponding to the crossover point between concentration polarization and activation polarization.However,the optimum protection potential is between -1.5 and -0.7 V since the current density at these values is low in the potentiostatic tests.When a galvanic cell is formed in the seawater,the welds exhibit electrochemically stable trends.Welded parts in galvanic tests with various area ratios are stable and have excellent anticorrosion characteristics.
文摘The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average size of 15 m and porosity in the range of 0.1 vol. % to 5vol. % . Two distinct TMP procedures are employed to close porosity and refine grain size:extrusion plus rolling and direct rolling. The material processed using the former method exhibits arelatively high superplasticity with a maximum superplastic elongation of 465 % , whereas thatprocessed using the latter method exhibits a maximum superplastic elongation of 295 % . Materialsprocessed using extrusion plus rolling and direct rolling both exhibit similar stress-strainbehavior and strain rate sensitivity factors. The strain rate factors are in the 0.3 to 0.5 range.The difference in their superplastic elongation is possibly the result of differences in grain sizeand available cavity nucleation sites provided by closed gas pores.
