楔形环管片是盾构隧道曲线段的重要组成部分。以珠海-澳门轻轨某急弯隧道为例,利用ANSYS有限元软件计算了楔形环管片在不同管片幅宽、楔形量、隧道曲率半径、千斤顶压力等条件下管片纵向接头的受力情况,重点分析了管片环间接头的最大正...楔形环管片是盾构隧道曲线段的重要组成部分。以珠海-澳门轻轨某急弯隧道为例,利用ANSYS有限元软件计算了楔形环管片在不同管片幅宽、楔形量、隧道曲率半径、千斤顶压力等条件下管片纵向接头的受力情况,重点分析了管片环间接头的最大正负弯矩。研究结果表明:随着盾构隧道曲线半径减小,正负最大弯矩均增大,不同隧道转弯半径下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;不论正负弯矩,均有管片幅宽越小最大弯矩越大的现象。不同管片幅宽下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;曲线半径为150 m时,最大正弯矩基本随着千斤顶压力呈线性增大的趋势,最大约为1 180 k N·m。研究结果对今后的急弯盾构隧道管片设计有一定的指导意义。展开更多
Based on the elastoplastic mechanical properties of the weld and heat affected zone metals obtained by a nanoindentation test, a theoretical calculation model was established for the forming limit diagram（FLD） of ta...Based on the elastoplastic mechanical properties of the weld and heat affected zone metals obtained by a nanoindentation test, a theoretical calculation model was established for the forming limit diagram（FLD） of tailor-welded blanks（TWBs） on the basis of plastic constitutive relations and Hosford yield criteria. Hemispherical punch bulging tests were performed to verify the FLD theoretical calculation results. The results demonstrated that not only the FLD theoretical calculation of base materials but also that of TWBs had a good agreement with their experiments. Besides, poorer formability of TWBs caused its FLD significantly lower than that of base materials. The theoretical calculation model offers a reliable approach to obtain the specific FLD of TWBs.展开更多
文摘楔形环管片是盾构隧道曲线段的重要组成部分。以珠海-澳门轻轨某急弯隧道为例,利用ANSYS有限元软件计算了楔形环管片在不同管片幅宽、楔形量、隧道曲率半径、千斤顶压力等条件下管片纵向接头的受力情况,重点分析了管片环间接头的最大正负弯矩。研究结果表明:随着盾构隧道曲线半径减小,正负最大弯矩均增大,不同隧道转弯半径下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;不论正负弯矩,均有管片幅宽越小最大弯矩越大的现象。不同管片幅宽下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;曲线半径为150 m时,最大正弯矩基本随着千斤顶压力呈线性增大的趋势,最大约为1 180 k N·m。研究结果对今后的急弯盾构隧道管片设计有一定的指导意义。
基金Project(51275444) supported by the National Natural Science Foundation of ChinaProject(20121333110003) supported by the Specialized Research Fund for the Doctoral Program of Higher Education,China+1 种基金Project(E2014203271) supported by the Natural Science Foundation–Steel and Iron Foundation of Hebei ProvinceChina
文摘Based on the elastoplastic mechanical properties of the weld and heat affected zone metals obtained by a nanoindentation test, a theoretical calculation model was established for the forming limit diagram（FLD） of tailor-welded blanks（TWBs） on the basis of plastic constitutive relations and Hosford yield criteria. Hemispherical punch bulging tests were performed to verify the FLD theoretical calculation results. The results demonstrated that not only the FLD theoretical calculation of base materials but also that of TWBs had a good agreement with their experiments. Besides, poorer formability of TWBs caused its FLD significantly lower than that of base materials. The theoretical calculation model offers a reliable approach to obtain the specific FLD of TWBs.
