The effect of processing parameters such as hot rolling and heat treatment on microstructure and mechanical properties was investigated for a new 0.27mass% C and Ni, Mo-free low alloy martensitic abrasion resistant st...The effect of processing parameters such as hot rolling and heat treatment on microstructure and mechanical properties was investigated for a new 0.27mass% C and Ni, Mo-free low alloy martensitic abrasion resistant steel. The three-body impact abrasive wear behavior was also analyzed. The results showed that two-step controlled rolling besides quenching at 880 ℃ and tempering at 170 ℃ could result in optimal mechanical property., the Brinell hardness, tensile strength, elongation and --40 ℃ impact toughness were 531, 1530 MPa, 11.8% and 58 J, re- spectively. The microstructure was of fine lath martensite with little retained austenite. Three-body impact abrasive wear results showed that wear mechanism was mainly of plastic deformation fatigue when the impact energy was 2 J, and the relative wear resistance was 1.04 times higher than that of the same grade compared steel under the same working condition. The optimal hardness and toughness match was the main reason of higher wear resistance.展开更多
The effects of heat treatment on the properties of multi element wear-resistant low-alloy steel （MLAWS） which is used to make the liner of rolling mill torus were researched. The results show that when quenching tem...The effects of heat treatment on the properties of multi element wear-resistant low-alloy steel （MLAWS） which is used to make the liner of rolling mill torus were researched. The results show that when quenching temperature is lower than 900℃, the hardness increases with the increase of temperature, and when quenching temperature is higher than 900℃, the hardness decreases with the increase of temperature. As quenching temperature is lower than 920℃, the effect of quenching temperature on the impact toughness is not obvious. When quenching temperature is higher than 920℃ , impact toughness decreases with the increase of temperature. When tempering temperature is higher than 450 ℃ , the hardness begins to decrease obviously. After tempering at 350℃, the best wear resistance was obtained. According to the service condition of rolling mill torus liner, the MLAWS is quenched from 900-920 ℃ and tempered at 350-370℃.展开更多
The effect of cryogenic treatment on the properties of Cr8-type cold work die steel was investigated. The results show that cryogenic treatment increases hardness by decreasing retained austenite, but the degree depen...The effect of cryogenic treatment on the properties of Cr8-type cold work die steel was investigated. The results show that cryogenic treatment increases hardness by decreasing retained austenite, but the degree depends on the austenitizing temperature. When quenching at lower austenitizing temperature, the steel can obtain higher tough- ness by cryogenic treatment substituting conventional treatment process. Cryogenic time has little effect on cryogenic treatment. Conversely, cryogenic temperature has a great effect on cryogenic treatment and the effect of cryogenic treatment is more obvious with decreasing cryogenic temperature. In addition, deep cryogenic treatment improves the wear resistance by precipitating more homogeneous specific carbides.展开更多
The microstructure, mechanical properties and wear resistance of high chromium cast steel containing boron after different heat treatments were studied by means of the optical microscopy （OM）, the scanning electron ...The microstructure, mechanical properties and wear resistance of high chromium cast steel containing boron after different heat treatments were studied by means of the optical microscopy （OM）, the scanning electron microscopy （SEM）, X-ray diffraction （XRD）, hardness, impact toughness, tensile and pin-on-disc abrasion tests. The results show that as cast microstructures of boron-free high chromium steel consist of martensite and a few （Cr, Fe）_7C_3 carbide, and the macro-hardness of boron-free high chromium steel is 55-57 HRC. After 0.5 mass% B was added into high chromium cast steel, as-cast structure transforms into eutectic （Fe, Cr）2B, （Cr, Fe）7 （C, B）a and martensite, and the macro-hardness reaches 58-60 HRC. High temperature quenching leads to the disconnection and isolated distribution of boride, and there are many （Cr,Fe）_23 （C,B）_6 precipitated phases in the quenching structure. Quenching from 1050 ℃, high chromium steel obtained the highest hardness, and the hardness of high chromium cast steel containing boron is higher than that of boron-free high chromium steel. The change of quenching temperature has no obvious effect on impact toughness of high chromium steel, and the increase of quenching temperature leads to tensile strength having an increasing tendency. At the same quenching temperature, the wear resistance of high chromium cast steel containing boron is more excellent than that of boron-free high chromium steel. High chromium cast steel guide containing boron has good performance while using in steel bar mill.展开更多
基金Item Sponsored by National Basic Research Program of China(2010CB630801)
文摘The effect of processing parameters such as hot rolling and heat treatment on microstructure and mechanical properties was investigated for a new 0.27mass% C and Ni, Mo-free low alloy martensitic abrasion resistant steel. The three-body impact abrasive wear behavior was also analyzed. The results showed that two-step controlled rolling besides quenching at 880 ℃ and tempering at 170 ℃ could result in optimal mechanical property., the Brinell hardness, tensile strength, elongation and --40 ℃ impact toughness were 531, 1530 MPa, 11.8% and 58 J, re- spectively. The microstructure was of fine lath martensite with little retained austenite. Three-body impact abrasive wear results showed that wear mechanism was mainly of plastic deformation fatigue when the impact energy was 2 J, and the relative wear resistance was 1.04 times higher than that of the same grade compared steel under the same working condition. The optimal hardness and toughness match was the main reason of higher wear resistance.
基金ItemSponsored by Tackle-Key-Programof Science and Technology Committee of Henan Province (042426002 ,0535010700)Henan Innovation Project for University Prominent Research Talents (2006KYCX022)
文摘The effects of heat treatment on the properties of multi element wear-resistant low-alloy steel （MLAWS） which is used to make the liner of rolling mill torus were researched. The results show that when quenching temperature is lower than 900℃, the hardness increases with the increase of temperature, and when quenching temperature is higher than 900℃, the hardness decreases with the increase of temperature. As quenching temperature is lower than 920℃, the effect of quenching temperature on the impact toughness is not obvious. When quenching temperature is higher than 920℃ , impact toughness decreases with the increase of temperature. When tempering temperature is higher than 450 ℃ , the hardness begins to decrease obviously. After tempering at 350℃, the best wear resistance was obtained. According to the service condition of rolling mill torus liner, the MLAWS is quenched from 900-920 ℃ and tempered at 350-370℃.
基金Item Sponsored by National Key Technologies Research and Development Program of China (2007BAE510B04)
文摘The effect of cryogenic treatment on the properties of Cr8-type cold work die steel was investigated. The results show that cryogenic treatment increases hardness by decreasing retained austenite, but the degree depends on the austenitizing temperature. When quenching at lower austenitizing temperature, the steel can obtain higher tough- ness by cryogenic treatment substituting conventional treatment process. Cryogenic time has little effect on cryogenic treatment. Conversely, cryogenic temperature has a great effect on cryogenic treatment and the effect of cryogenic treatment is more obvious with decreasing cryogenic temperature. In addition, deep cryogenic treatment improves the wear resistance by precipitating more homogeneous specific carbides.
基金Item Sponsored by National Natural Science Foundation of China(51274016)Natural Science Foundation of Beijing of China(2142009)Plan Item of Beijing Education Committee of China(KM201310005003)
文摘The microstructure, mechanical properties and wear resistance of high chromium cast steel containing boron after different heat treatments were studied by means of the optical microscopy （OM）, the scanning electron microscopy （SEM）, X-ray diffraction （XRD）, hardness, impact toughness, tensile and pin-on-disc abrasion tests. The results show that as cast microstructures of boron-free high chromium steel consist of martensite and a few （Cr, Fe）_7C_3 carbide, and the macro-hardness of boron-free high chromium steel is 55-57 HRC. After 0.5 mass% B was added into high chromium cast steel, as-cast structure transforms into eutectic （Fe, Cr）2B, （Cr, Fe）7 （C, B）a and martensite, and the macro-hardness reaches 58-60 HRC. High temperature quenching leads to the disconnection and isolated distribution of boride, and there are many （Cr,Fe）_23 （C,B）_6 precipitated phases in the quenching structure. Quenching from 1050 ℃, high chromium steel obtained the highest hardness, and the hardness of high chromium cast steel containing boron is higher than that of boron-free high chromium steel. The change of quenching temperature has no obvious effect on impact toughness of high chromium steel, and the increase of quenching temperature leads to tensile strength having an increasing tendency. At the same quenching temperature, the wear resistance of high chromium cast steel containing boron is more excellent than that of boron-free high chromium steel. High chromium cast steel guide containing boron has good performance while using in steel bar mill.
