Mechanical properties of a newly developed microalloyed bainitic steel were investigated after the hot forging, air cooling and tempering process. The microstructure of the as forged bainitic steel mainly consists of ...Mechanical properties of a newly developed microalloyed bainitic steel were investigated after the hot forging, air cooling and tempering process. The microstructure of the as forged bainitic steel mainly consists of granular bainite and -20 vol. % martensite. The fraction of retained austenite remains unchanged until tempering at 200 ℃, above which it decreases significantly. The increase of tempering temperature leads to decreases of both ultimate tensile strength and total elongation but decreases of both yield strength and reduction of area. The maximum and mini- mum values of impact toughness were observed after tempering at around 200 and 400 ℃, respectively. These effects are mainly attributed to the decomposition of martensite/austenite con stituents and the tempering effects in martensite. The tempering of the forged bainitic steel at around 200 ℃ results in an excellent combination of strength and toughness, which is comparable to that of the conventional quenched and-tempered 40Cr steel. Therefore, low-tempering treatment coupled with post-forging residual stress relieving is a feasible method to further improve the mechanical prooerties of the bainitic foging steel.展开更多
The variations of microstructures and mechanical properties of steels 15CrMnMoV, 18Mn2CrMoB,18Cr2Ni4W,30CrMnSi,30CrMnSiNi2 and 40CrMnSiMoV,which were tempered at different temperatures after austempering and continuou...The variations of microstructures and mechanical properties of steels 15CrMnMoV, 18Mn2CrMoB,18Cr2Ni4W,30CrMnSi,30CrMnSiNi2 and 40CrMnSiMoV,which were tempered at different temperatures after austempering and continuous cooling at given rates, have been investigated.Based on the experimental results,the behaviour and mechanism of tempered bainite embrittlement(TBE)have been discussed.Finally,the theoretical and prac- tical basis for selecting the optimum tempering temperature of steels with bainite structure af- ter heat treatment are proposed.展开更多
A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of...A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of both steels, new grade and ASTM T/P 23, were hot rolled at 900℃ and then submitted to a thermal treatment consisting of solubilization at 1050℃ and tempering at 700℃. Tempered bainitic microstructures obtained contain second phases reinforcing carbide particles, mainly M_6C and M_（23）C_6 at the boundaries of both, prior austenite grains and bainitic ferrite laths, as well as MC within the grains. Mechanical properties at temperatures ranging from 540 to 600℃ were studied by strain-ratechange tests in compression at strain rates between 10^（-7） and 10^（-4）s^（-1）. These tests showed high stress exponents（n ≥ 20） and activation energies（Q ≈ 400 k J/mol） for both alloys, which were associated with a dislocation movement mechanism with a strong interaction between dislocations and precipitates. On the other hand, a creep exponent of 5 was derived for the stress dependence of minimum creep rate from conventional-type creep tests at 600℃. Although this stress exponent is usually related to a dislocation climb controlled creep mechanism, remarkable microstructural degradation observed with increasing creep time makes difficult to elucidate the true deformation mechanism controlling creep.展开更多
基金financially supported by the National Key Research&Development Program of China under grant No.2016YFB0300100the Fundamental Research Funds for the Central Universities(No.2014JBM108)the Prospective Joint Study of Industry-University Cooperation of Jiangsu Province under grant No.BY2015009-02
文摘Mechanical properties of a newly developed microalloyed bainitic steel were investigated after the hot forging, air cooling and tempering process. The microstructure of the as forged bainitic steel mainly consists of granular bainite and -20 vol. % martensite. The fraction of retained austenite remains unchanged until tempering at 200 ℃, above which it decreases significantly. The increase of tempering temperature leads to decreases of both ultimate tensile strength and total elongation but decreases of both yield strength and reduction of area. The maximum and mini- mum values of impact toughness were observed after tempering at around 200 and 400 ℃, respectively. These effects are mainly attributed to the decomposition of martensite/austenite con stituents and the tempering effects in martensite. The tempering of the forged bainitic steel at around 200 ℃ results in an excellent combination of strength and toughness, which is comparable to that of the conventional quenched and-tempered 40Cr steel. Therefore, low-tempering treatment coupled with post-forging residual stress relieving is a feasible method to further improve the mechanical prooerties of the bainitic foging steel.
文摘The variations of microstructures and mechanical properties of steels 15CrMnMoV, 18Mn2CrMoB,18Cr2Ni4W,30CrMnSi,30CrMnSiNi2 and 40CrMnSiMoV,which were tempered at different temperatures after austempering and continuous cooling at given rates, have been investigated.Based on the experimental results,the behaviour and mechanism of tempered bainite embrittlement(TBE)have been discussed.Finally,the theoretical and prac- tical basis for selecting the optimum tempering temperature of steels with bainite structure af- ter heat treatment are proposed.
基金supported by the Spanish Ministry of Economy and Competitiveness(MINECO)under Grant MAT2012-39124,MAT2015-68919,and MAT2016-80875
文摘A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of both steels, new grade and ASTM T/P 23, were hot rolled at 900℃ and then submitted to a thermal treatment consisting of solubilization at 1050℃ and tempering at 700℃. Tempered bainitic microstructures obtained contain second phases reinforcing carbide particles, mainly M_6C and M_（23）C_6 at the boundaries of both, prior austenite grains and bainitic ferrite laths, as well as MC within the grains. Mechanical properties at temperatures ranging from 540 to 600℃ were studied by strain-ratechange tests in compression at strain rates between 10^（-7） and 10^（-4）s^（-1）. These tests showed high stress exponents（n ≥ 20） and activation energies（Q ≈ 400 k J/mol） for both alloys, which were associated with a dislocation movement mechanism with a strong interaction between dislocations and precipitates. On the other hand, a creep exponent of 5 was derived for the stress dependence of minimum creep rate from conventional-type creep tests at 600℃. Although this stress exponent is usually related to a dislocation climb controlled creep mechanism, remarkable microstructural degradation observed with increasing creep time makes difficult to elucidate the true deformation mechanism controlling creep.
