Based on the statics theory, a novel and feasible twice-suspended-mass method(TSMM) was proposed to deal with the seldom-studied issue of fault diagnosis for damping springs of large vibrating screen(LVS). With the st...Based on the statics theory, a novel and feasible twice-suspended-mass method(TSMM) was proposed to deal with the seldom-studied issue of fault diagnosis for damping springs of large vibrating screen(LVS). With the static balance characteristic of the screen body/surface as well as the deformation compatibility relation of springs considered, static model of the screen surface under a certain load was established to calculate compression deformation of each spring. Accuracy of the model was validated by both an experiment based on the suspended mass method and the properties of the 3D deformation space in a numerical simulation. Furthermore, by adopting the Taylor formula and the control variate method, quantitative relationship between the change of damping spring deformation and the change of spring stiffness, defined as the deformation sensitive coefficient(DSC), was derived mathematically, from which principle of the TSMM for spring fault diagnosis is clarified. In the end, an experiment was carried out and results show that the TSMM is applicable for diagnosing the fault of single spring in a LVS.展开更多
The flow field distribution in centrifugal compressor is significantly affected by the non-axisymmetric geometry structure of the volute.The experimental and numerical simulation methods were adopted in this work to s...The flow field distribution in centrifugal compressor is significantly affected by the non-axisymmetric geometry structure of the volute.The experimental and numerical simulation methods were adopted in this work to study the compressor flow field distribution with different flow conditions.The results show that the pressure distribution in volute is characterized by the circumferential non-uniform phenomenon and the pressure fluctuation on the high static pressure zone propagates reversely to upstream,which results in the non-axisymmetric flow inside the compressor.The non-uniform level of pressure distribution in large flow condition is higher than that in small flow condition,its effect on the upstream flow field is also stronger.Additionally,the non-uniform circumferential pressure distribution in volute brings the non-axisymmetric flow at impeller outlet.In different flow conditions,the circumferential variation of the absolute flow angle at impeller outlet is also different.Meanwhile,the non-axisymmetric flow characteristics in internal impeller can be also reflected by the distribution of the mass flow.The high static pressure region of the volute corresponds to the decrease of mass flow in upstream blade channel,while the low static pressure zone of the volute corresponds to the increase of the mass flow.In small flow condition,the mass flow difference in the blade channel is bigger than that in the large flow condition.展开更多
The mechanically stirred internal loop airlift reactors equipped with or without static mixers are devised for intensification of gas-liquid mass transfer rate. The influences of superficial gas velocity, agitation o...The mechanically stirred internal loop airlift reactors equipped with or without static mixers are devised for intensification of gas-liquid mass transfer rate. The influences of superficial gas velocity, agitation or static mixers on gas hold-up, mixing time, liquid circulating velocity and volumetric mass transfer coefficient have been investigated with tap water and carboxymethyl cellulose (CMC) aqueous solution. The experimental results indicate that mechanical agitation is more efficacious than static mixer in highly viscous media for improving mass transfer in airlift reactors. The empirical correlation of volumetric mass transfer coefficient with apparent viscosity, and energy consumption for mechanical agitation and aeration is developed.展开更多
Externally pressurized spherical air bearings are the key component of the three-axis air bearing table, and the manufacturing errors of the bearing affects the performance of the air bearing table. However, the manuf...Externally pressurized spherical air bearings are the key component of the three-axis air bearing table, and the manufacturing errors of the bearing affects the performance of the air bearing table. However, the manufacturing errors are unavoidable, and the pursuit to enhance the manufacturing accuracy will increase the cost greatly. In order to provide some theoretical guideline for the tolerance choice in the design of the externally pressurized spherical air bearings with inherent compensation, the effects of several manufacturing errors on the static characteristics of the air bearing are studied. Due to the complex geometry of the computational domain, an unstructured meshing technology is used for mesh generation. A finite-volume method is adopted to discretize the three-dimensional steady-state compressible Navier-Stokes equations. A modified SIMPLE algorithm which is suitable for compressible flows is applied to solve the discretized governing equations. The effects of the dimension error and the roundness error of the ball head and the ball socket on the static characteristics are investigated. The investigation result shows that the positive dimension error and the oblate spheroid-type roundness error of the ball head as well as the negative dimension error and the prolate spheroid-type roundness error of the ball socket can improve the bearing capacity and static stiffness of the air bearings by reducing the mass flow. The calculation method proposed in this paper fits well for the general principle, which can be extended to the characteristics analysis of other air bearings.展开更多
In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric vo...In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.展开更多
基金Project(20120095110001)supported by the PhD Programs Foundation of Ministry of Education of ChinaProject(51134022,51221462)supported by the National Natural Science Foundation of China+1 种基金Project(CXZZ13_0927)supported by Research and Innovation Program for College Graduates of Jiangsu Province,ChinaProject(2013DXS03)supported by the Fundamental Research Funds for Central Universities of China
文摘Based on the statics theory, a novel and feasible twice-suspended-mass method(TSMM) was proposed to deal with the seldom-studied issue of fault diagnosis for damping springs of large vibrating screen(LVS). With the static balance characteristic of the screen body/surface as well as the deformation compatibility relation of springs considered, static model of the screen surface under a certain load was established to calculate compression deformation of each spring. Accuracy of the model was validated by both an experiment based on the suspended mass method and the properties of the 3D deformation space in a numerical simulation. Furthermore, by adopting the Taylor formula and the control variate method, quantitative relationship between the change of damping spring deformation and the change of spring stiffness, defined as the deformation sensitive coefficient(DSC), was derived mathematically, from which principle of the TSMM for spring fault diagnosis is clarified. In the end, an experiment was carried out and results show that the TSMM is applicable for diagnosing the fault of single spring in a LVS.
基金sponsored by the National Natural Science Foundation of China(No.51276017)
文摘The flow field distribution in centrifugal compressor is significantly affected by the non-axisymmetric geometry structure of the volute.The experimental and numerical simulation methods were adopted in this work to study the compressor flow field distribution with different flow conditions.The results show that the pressure distribution in volute is characterized by the circumferential non-uniform phenomenon and the pressure fluctuation on the high static pressure zone propagates reversely to upstream,which results in the non-axisymmetric flow inside the compressor.The non-uniform level of pressure distribution in large flow condition is higher than that in small flow condition,its effect on the upstream flow field is also stronger.Additionally,the non-uniform circumferential pressure distribution in volute brings the non-axisymmetric flow at impeller outlet.In different flow conditions,the circumferential variation of the absolute flow angle at impeller outlet is also different.Meanwhile,the non-axisymmetric flow characteristics in internal impeller can be also reflected by the distribution of the mass flow.The high static pressure region of the volute corresponds to the decrease of mass flow in upstream blade channel,while the low static pressure zone of the volute corresponds to the increase of the mass flow.In small flow condition,the mass flow difference in the blade channel is bigger than that in the large flow condition.
文摘The mechanically stirred internal loop airlift reactors equipped with or without static mixers are devised for intensification of gas-liquid mass transfer rate. The influences of superficial gas velocity, agitation or static mixers on gas hold-up, mixing time, liquid circulating velocity and volumetric mass transfer coefficient have been investigated with tap water and carboxymethyl cellulose (CMC) aqueous solution. The experimental results indicate that mechanical agitation is more efficacious than static mixer in highly viscous media for improving mass transfer in airlift reactors. The empirical correlation of volumetric mass transfer coefficient with apparent viscosity, and energy consumption for mechanical agitation and aeration is developed.
基金supported by National Natural Science Foundation ofChina (Grant No. 50335010)
文摘Externally pressurized spherical air bearings are the key component of the three-axis air bearing table, and the manufacturing errors of the bearing affects the performance of the air bearing table. However, the manufacturing errors are unavoidable, and the pursuit to enhance the manufacturing accuracy will increase the cost greatly. In order to provide some theoretical guideline for the tolerance choice in the design of the externally pressurized spherical air bearings with inherent compensation, the effects of several manufacturing errors on the static characteristics of the air bearing are studied. Due to the complex geometry of the computational domain, an unstructured meshing technology is used for mesh generation. A finite-volume method is adopted to discretize the three-dimensional steady-state compressible Navier-Stokes equations. A modified SIMPLE algorithm which is suitable for compressible flows is applied to solve the discretized governing equations. The effects of the dimension error and the roundness error of the ball head and the ball socket on the static characteristics are investigated. The investigation result shows that the positive dimension error and the oblate spheroid-type roundness error of the ball head as well as the negative dimension error and the prolate spheroid-type roundness error of the ball socket can improve the bearing capacity and static stiffness of the air bearings by reducing the mass flow. The calculation method proposed in this paper fits well for the general principle, which can be extended to the characteristics analysis of other air bearings.
文摘In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.
