Irregular grains, high interfacial stresses and anisotropic properties widely exist in 3D-printed metallic materials, and this paper investigated the effects of heat treatment on the microstructural, mechanical and co...Irregular grains, high interfacial stresses and anisotropic properties widely exist in 3D-printed metallic materials, and this paper investigated the effects of heat treatment on the microstructural, mechanical and corrosion properties of 316 L stainless steel fabricated by selective laser melting. Sub-grains and low-angle boundaries exist in the as-received selective laser melted(SLMed) 316 L stainless steel. After heat treatment at 1050℃, the sub-grains and low-angle boundaries changed slightly, and the stress state and strength decreased to some extent due to the decrease of dislocation density. After heat treatment at 1200℃, the grains became uniform, and the dislocation cells vanished, which led to a sharp decline in the hardness and strength. However, the ductility was improved after recrystallization heat treatment.The passive film thickness and corrosion potential of the SLMed 316 L stainless steel decreased after heat treatment, and the pitting potential also decreased due to the accelerated transition from metastable to steady-state pitting;this accelerated transition was caused by the presence of weak passive films at the enlarged pores after heat treatment, especially for an adequate solid solution treatment.展开更多
By means of surface mechanical attrition treatment （ SMAT）, the groin size with a diameter of aboat 60hm formed at about 20μm depth and numerous mechanical twins at about 50μm depth from the treated surface were ...By means of surface mechanical attrition treatment （ SMAT）, the groin size with a diameter of aboat 60hm formed at about 20μm depth and numerous mechanical twins at about 50μm depth from the treated surface were synthesized in 316L stainless steel because of the different distributions of strain and strain rate along depth orientation. For instance the maximum strain rate reached 10^3-10^4s^-1 on the top surface. The relationship between the microsturcture and the corrosion property was studied in 0.05M H2SO4＋ 0.25M Na2SO4 aqueous solution, and the results show an extreme improvement of corrosion resistance owing to the appearance of twin boundaries and the obvious reduction in corrosion resistance attributed to the presence of nanocrystaline boundaries.展开更多
The corrosion behavior of 316L stainless steel （31 6L SS） has been investigated in solutions containing various concentrations of chloride ions by using potentiodynamic polarization, capacitance measurement and Mott...The corrosion behavior of 316L stainless steel （31 6L SS） has been investigated in solutions containing various concentrations of chloride ions by using potentiodynamic polarization, capacitance measurement and Mott- Schottky relationship analysis （M-S）. The result indicates that passive currents change slightly with the addition of chloride ions. The pitting potential （Epit） decreases linearly with Iog[CI-]. Correspondingly, the point defect diffusion coefficient （Do） of the passive film increases linearly with increasing Iog[CI-]. The results also indicate that the pitting corrosion of 316L SS follows the adsorption mechanism in NaCI solution.展开更多
This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl...This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl（1 mol/L）＋H_2SO_4（0.5 mol/L）solution.Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process.Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagneticα′-martensite phase under the stresses applied during cold rolling.This finding is in agreement with magnetic measurements using a vibrating sample magnetometer.Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage,representing a reduction in the material’s work-hardening ability.Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy.In contrast to the uniform corrosion,wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects,the passive potential range and breakdown potential increased by cold working,showing greater resistance to pit nucleation.Although pits were formed,the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop,as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.展开更多
With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawat...With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawater lubrication are still very fewer, especially experimental research. The influences of smooth and non-smooth surface on the frictional properties of the glass fiber-epoxy resin composite（GF/EPR） coupled with stainless steel 316 L are investigated under natural seawater lubrication in this paper. The tested non-smooth surfaces include the surfaces with semi-spherical pits, the conical pits, the cone-cylinder combined pits, the cylindrical pits and through holes. The friction and wear tests are performed using a ring-on-disc test rig under 60 N load and 1000 r/min rotational speed. The tests results show that GF/EPR with bionic non-smooth surface has quite lower friction coefficient and better wear resistance than GF/EPR with smooth surface without pits. The average friction coefficient of GF/EPR with semi-spherical pits is 0.088, which shows the largest reduction is approximately 63.18% of GF/EPR with smooth surface. In addition, the wear debris on the worn surfaces of GF/EPR are observed by a confocal scanning laser microscope. It is shown that the primary wear mechanism is the abrasive wear. The research results provide some design parameters for non-smooth surface, and the experiment results can serve as a beneficial supplement to non-smooth surface study.展开更多
The corrosion behavior and mechanical properties of 316 L stainless steel(SS) fabricated via selective laser melting(SLM) were clarified by potentiodynamic polarization measurements, immersion tests, and tensile exper...The corrosion behavior and mechanical properties of 316 L stainless steel(SS) fabricated via selective laser melting(SLM) were clarified by potentiodynamic polarization measurements, immersion tests, and tensile experiments. The microstructural anisotropy of SLMed 316 L SS was also investigated by electron back-scattered diffraction and transmission electron microscopy. The grain sizes of the SLMed 316 L SS in the XOZ plane were smaller than those of the SLMed 316 L SS in the XOY plane, and a greater number of low-angle boundaries were present in the XOY plane, resulting in lower elongation for the XOY plane than for the XOZ plane. The SLMed 316 L was expected to exhibit higher strength but lower ductility than the wrought 316 L, which was attributed to the high density of dislocations. The pitting potentials of the SLMed 316 L samples were universally higher than those of the wrought sample in chloride solutions because of the annihilation of MnS or(Ca,Al)-oxides during the rapid solidification. However, the molten pool boundaries preferentially dissolved in aggressive solutions and the damage of the SLMed 316 L in FeCl3 solution was more serious after long-term service, indicating poor durability.展开更多
Bionic non-smooth surface is widely applied in metal and ceramics materials. In order to introduce this technology to high pressure seawater pump, the influence of bionic non-smooth surface on the engineering plastics...Bionic non-smooth surface is widely applied in metal and ceramics materials. In order to introduce this technology to high pressure seawater pump, the influence of bionic non-smooth surface on the engineering plastics used in pump should be investigated. The comparative tests are carried out with a ring-on-disc configuration under 800, 1000, 1200 and 1400 r/min in order to research the influence of the bionic non-smooth surface on glass fiber-epoxy resin composite（GF/EPR） under natural seawater lubrication. The disc surfaces are textured with five kinds of pits, which are semi-spherical, conical, cone-cylinder combined, cylindrical pits and through holes, respectively. A smooth surface is tested as reference. The results show that the lubrication performance of dimpled GF/EPR sample is much better than that of the smooth sample under all rotational speeds. The semi-spherical pits surface has more obvious friction reduction than the others, which shows that the least reduction is approximately 43.29% of smooth surface under 1200 r/rain. However, the wear level is only marginally influenced by dimples. The surface morphology investigations disclose severe modifications caused by abrasive wear primarily. The results are helpful to vary friction properties of GF/EPR by non-smooth surface, or provide references to the design of non-smooth surfaces under certain condition.展开更多
This study is conducted to develop an innovative and attractive selective laser melting(SLM)method to produce 316 L stainless steel materials with excellent mechanical performance and complex part shape.In this work,t...This study is conducted to develop an innovative and attractive selective laser melting(SLM)method to produce 316 L stainless steel materials with excellent mechanical performance and complex part shape.In this work,the subregional manufacturing strategy,which separates the special parts from the components using an optimized process,was proposed.The results showed that produced 316 L materials exhibited superior strength of^755 MPa and good ductility.In the as-built parts,austenite with preferred orientation of the(220)plane,δ-ferrite,and a small amount of CrO phases were present.In addition,the crystal size was fine,which contributed to the enhancement of the parts’mechanical properties.The structural anisotropy mechanism of the materials was also investigated for a group of half-sized samples with variable inclination directions.This technique was used to fabricate a set of impellers with helical bevels and high-precision planetary gears,demonstrating its strong potential for use in practical applications.展开更多
In this study, the applicability of plasma nitriding treatment in the production of non-magnetic and corrosion resistant layer on 316L stainless steel implant material was investigated. 316L stainless steel substrates...In this study, the applicability of plasma nitriding treatment in the production of non-magnetic and corrosion resistant layer on 316L stainless steel implant material was investigated. 316L stainless steel substrates were plasma nitrided at temperatures of 350 ℃, 375 ℃, 400 ℃, 425 ℃ and 450 ℃ for 2 h in a gas mixture of 50% N2-50% H2, respectively. It was determined that the treatment temperature is the most important factor on the properties of the corrosion resistant layer of 316L stainless steel. The results show that s-phase formed at the temperatures under 400 ℃, and at the temperatures above 400 ℃, instead of s-phase, CrN and y＇-Fe4N phases were observed in the modified layer. The electrical resistivity and surface roughness of the modified layer increase with treatment temperature. Under 400 ℃ the corrosion resistance increased with the temperature, above 400 ℃ it decreased with the increase in treatment temperature. It was analyzed that the electrical resistivity and the soft （ideal） ferro- magnetic properties of 316L stainless steel increased with treatment temperature during nitriding treatment. Also, plasma ni- triding at low temperatures provided magnetic behavior close to the ideal untreated 316L stainless steel.展开更多
This research explores the prospect of fabricating a face-centered cubic(fcc) Ni-base alloy cladding(Inconel 690) on an fcc Fe-base alloy(316 L stainless-steel) having improved mechanical properties and reduced sensit...This research explores the prospect of fabricating a face-centered cubic(fcc) Ni-base alloy cladding(Inconel 690) on an fcc Fe-base alloy(316 L stainless-steel) having improved mechanical properties and reduced sensitivity to corrosion through grain boundary and microstructure engineering concepts enabled by additive manufacturing(AM) utilizing electron-beam powder bed fusion(EPBF). The unique solidification and associated constitutional supercooling phenomena characteristic of EPBF promotes[100] textured and extended columnar grains having lower energy grain boundaries as opposed to random, high-angle grain boundaries, but no coherent {111} twin boundaries characteristic of conventional thermo-mechanically processed fcc metals and alloys, including Inconel 690 and 316 L stainless-steel.In addition to [100] textured grains, columnar grains were produced by EPBF fabrication of Inconel 690 claddings on 316 L stainless-steel substrates. Also, irregular 2–3 μm diameter, low energy subgrains were formed along with dislocation densities varying from 108 to 109 cm^2, and a homogeneous distribution of Cr_(23)C_6 precipitates. Precipitates were formed within the grains(with ~3 μm interparticle spacing),but not in the subgrain or columnar grain boundaries. These inclusive, hierarchical microstructures produced a tensile yield strength of 0.527 GPa, elongation of 21%, and Vickers microindentation hardness of 2.33 GPa for the Inconel 690 cladding in contrast to a tensile yield strength of 0.327 GPa, elongation of 53%, and Vickers microindentation hardness of 1.78 GPa, respectively for the wrought 316 L stainlesssteel substrate. Aging of both the Inconel 690 cladding and the 316 L stainless-steel substrate at 685?C for50 h precipitated Cr_(23)C_6 carbides in the Inconel 690 columnar grain boundaries, but not in the low-angle(and low energy) subgrain boundaries. In contrast, Cr_(23)C_6 carbides precipitated in the 316 L stainless-steel grain boundaries, but not in the low energy coherent {111} twin boundaries. Consequently展开更多
基金supported financially by the National Key Research and Development Program of China (No. 2017YFB 0702300)the National Natural Science Foundation of China (No. 51671029)the Fundamental Research Funds for the Central Universities (No. FRF-TP-17-002B)
文摘Irregular grains, high interfacial stresses and anisotropic properties widely exist in 3D-printed metallic materials, and this paper investigated the effects of heat treatment on the microstructural, mechanical and corrosion properties of 316 L stainless steel fabricated by selective laser melting. Sub-grains and low-angle boundaries exist in the as-received selective laser melted(SLMed) 316 L stainless steel. After heat treatment at 1050℃, the sub-grains and low-angle boundaries changed slightly, and the stress state and strength decreased to some extent due to the decrease of dislocation density. After heat treatment at 1200℃, the grains became uniform, and the dislocation cells vanished, which led to a sharp decline in the hardness and strength. However, the ductility was improved after recrystallization heat treatment.The passive film thickness and corrosion potential of the SLMed 316 L stainless steel decreased after heat treatment, and the pitting potential also decreased due to the accelerated transition from metastable to steady-state pitting;this accelerated transition was caused by the presence of weak passive films at the enlarged pores after heat treatment, especially for an adequate solid solution treatment.
文摘By means of surface mechanical attrition treatment （ SMAT）, the groin size with a diameter of aboat 60hm formed at about 20μm depth and numerous mechanical twins at about 50μm depth from the treated surface were synthesized in 316L stainless steel because of the different distributions of strain and strain rate along depth orientation. For instance the maximum strain rate reached 10^3-10^4s^-1 on the top surface. The relationship between the microsturcture and the corrosion property was studied in 0.05M H2SO4＋ 0.25M Na2SO4 aqueous solution, and the results show an extreme improvement of corrosion resistance owing to the appearance of twin boundaries and the obvious reduction in corrosion resistance attributed to the presence of nanocrystaline boundaries.
基金the financial support from the National Natural Science Foundation of China (Nos. 50971050 and 50771038)the Ministry of Science and Technology of China (No. 2012FY113000)the Fundamental Research Founds for the Central Universities (No. HEUCF101005).
文摘The corrosion behavior of 316L stainless steel （31 6L SS） has been investigated in solutions containing various concentrations of chloride ions by using potentiodynamic polarization, capacitance measurement and Mott- Schottky relationship analysis （M-S）. The result indicates that passive currents change slightly with the addition of chloride ions. The pitting potential （Epit） decreases linearly with Iog[CI-]. Correspondingly, the point defect diffusion coefficient （Do） of the passive film increases linearly with increasing Iog[CI-]. The results also indicate that the pitting corrosion of 316L SS follows the adsorption mechanism in NaCI solution.
基金Shahid Chamran University of Ahvaz for supporting this research
文摘This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl（1 mol/L）＋H_2SO_4（0.5 mol/L）solution.Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process.Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagneticα′-martensite phase under the stresses applied during cold rolling.This finding is in agreement with magnetic measurements using a vibrating sample magnetometer.Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage,representing a reduction in the material’s work-hardening ability.Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy.In contrast to the uniform corrosion,wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects,the passive potential range and breakdown potential increased by cold working,showing greater resistance to pit nucleation.Although pits were formed,the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop,as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.
基金Supported by National Natural Science Foundation of China(Grant No.51375421)Hebei Provincial Key Project of Science and Technology Research of(ZD20131027)
文摘With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawater lubrication are still very fewer, especially experimental research. The influences of smooth and non-smooth surface on the frictional properties of the glass fiber-epoxy resin composite（GF/EPR） coupled with stainless steel 316 L are investigated under natural seawater lubrication in this paper. The tested non-smooth surfaces include the surfaces with semi-spherical pits, the conical pits, the cone-cylinder combined pits, the cylindrical pits and through holes. The friction and wear tests are performed using a ring-on-disc test rig under 60 N load and 1000 r/min rotational speed. The tests results show that GF/EPR with bionic non-smooth surface has quite lower friction coefficient and better wear resistance than GF/EPR with smooth surface without pits. The average friction coefficient of GF/EPR with semi-spherical pits is 0.088, which shows the largest reduction is approximately 63.18% of GF/EPR with smooth surface. In addition, the wear debris on the worn surfaces of GF/EPR are observed by a confocal scanning laser microscope. It is shown that the primary wear mechanism is the abrasive wear. The research results provide some design parameters for non-smooth surface, and the experiment results can serve as a beneficial supplement to non-smooth surface study.
基金financially supported by the Shanghai Materials Genome Institute No. 5 (No. 16DZ2260605)the Shanghai Sailing Program (No. 17YF1405400)the Project to Strengthen Industrial Development at the Grass-roots Level (No. TC160A310/19)
文摘The corrosion behavior and mechanical properties of 316 L stainless steel(SS) fabricated via selective laser melting(SLM) were clarified by potentiodynamic polarization measurements, immersion tests, and tensile experiments. The microstructural anisotropy of SLMed 316 L SS was also investigated by electron back-scattered diffraction and transmission electron microscopy. The grain sizes of the SLMed 316 L SS in the XOZ plane were smaller than those of the SLMed 316 L SS in the XOY plane, and a greater number of low-angle boundaries were present in the XOY plane, resulting in lower elongation for the XOY plane than for the XOZ plane. The SLMed 316 L was expected to exhibit higher strength but lower ductility than the wrought 316 L, which was attributed to the high density of dislocations. The pitting potentials of the SLMed 316 L samples were universally higher than those of the wrought sample in chloride solutions because of the annihilation of MnS or(Ca,Al)-oxides during the rapid solidification. However, the molten pool boundaries preferentially dissolved in aggressive solutions and the damage of the SLMed 316 L in FeCl3 solution was more serious after long-term service, indicating poor durability.
基金Supported by National Natural Science Foundation of China(Grant No.51375421)Key Project of Science and Technology Research of Hebei Province,China(ZD20131027)
文摘Bionic non-smooth surface is widely applied in metal and ceramics materials. In order to introduce this technology to high pressure seawater pump, the influence of bionic non-smooth surface on the engineering plastics used in pump should be investigated. The comparative tests are carried out with a ring-on-disc configuration under 800, 1000, 1200 and 1400 r/min in order to research the influence of the bionic non-smooth surface on glass fiber-epoxy resin composite（GF/EPR） under natural seawater lubrication. The disc surfaces are textured with five kinds of pits, which are semi-spherical, conical, cone-cylinder combined, cylindrical pits and through holes, respectively. A smooth surface is tested as reference. The results show that the lubrication performance of dimpled GF/EPR sample is much better than that of the smooth sample under all rotational speeds. The semi-spherical pits surface has more obvious friction reduction than the others, which shows that the least reduction is approximately 43.29% of smooth surface under 1200 r/rain. However, the wear level is only marginally influenced by dimples. The surface morphology investigations disclose severe modifications caused by abrasive wear primarily. The results are helpful to vary friction properties of GF/EPR by non-smooth surface, or provide references to the design of non-smooth surfaces under certain condition.
基金supported by the Key R&D Programs of Sichuan Province of China (No. 2018GZ0145)the Science and Technology Planning Projects of Zigong of Sichuan Province (No. 2018CDZG-1)the Major Scientific and Technological Key Bidding Projects in Panzhihua Experimental Zone (No. 1640STC30166/01)
文摘This study is conducted to develop an innovative and attractive selective laser melting(SLM)method to produce 316 L stainless steel materials with excellent mechanical performance and complex part shape.In this work,the subregional manufacturing strategy,which separates the special parts from the components using an optimized process,was proposed.The results showed that produced 316 L materials exhibited superior strength of^755 MPa and good ductility.In the as-built parts,austenite with preferred orientation of the(220)plane,δ-ferrite,and a small amount of CrO phases were present.In addition,the crystal size was fine,which contributed to the enhancement of the parts’mechanical properties.The structural anisotropy mechanism of the materials was also investigated for a group of half-sized samples with variable inclination directions.This technique was used to fabricate a set of impellers with helical bevels and high-precision planetary gears,demonstrating its strong potential for use in practical applications.
文摘In this study, the applicability of plasma nitriding treatment in the production of non-magnetic and corrosion resistant layer on 316L stainless steel implant material was investigated. 316L stainless steel substrates were plasma nitrided at temperatures of 350 ℃, 375 ℃, 400 ℃, 425 ℃ and 450 ℃ for 2 h in a gas mixture of 50% N2-50% H2, respectively. It was determined that the treatment temperature is the most important factor on the properties of the corrosion resistant layer of 316L stainless steel. The results show that s-phase formed at the temperatures under 400 ℃, and at the temperatures above 400 ℃, instead of s-phase, CrN and y＇-Fe4N phases were observed in the modified layer. The electrical resistivity and surface roughness of the modified layer increase with treatment temperature. Under 400 ℃ the corrosion resistance increased with the temperature, above 400 ℃ it decreased with the increase in treatment temperature. It was analyzed that the electrical resistivity and the soft （ideal） ferro- magnetic properties of 316L stainless steel increased with treatment temperature during nitriding treatment. Also, plasma ni- triding at low temperatures provided magnetic behavior close to the ideal untreated 316L stainless steel.
基金Support for this project was provided by US Department of Energy grant DE-SC0011826
文摘This research explores the prospect of fabricating a face-centered cubic(fcc) Ni-base alloy cladding(Inconel 690) on an fcc Fe-base alloy(316 L stainless-steel) having improved mechanical properties and reduced sensitivity to corrosion through grain boundary and microstructure engineering concepts enabled by additive manufacturing(AM) utilizing electron-beam powder bed fusion(EPBF). The unique solidification and associated constitutional supercooling phenomena characteristic of EPBF promotes[100] textured and extended columnar grains having lower energy grain boundaries as opposed to random, high-angle grain boundaries, but no coherent {111} twin boundaries characteristic of conventional thermo-mechanically processed fcc metals and alloys, including Inconel 690 and 316 L stainless-steel.In addition to [100] textured grains, columnar grains were produced by EPBF fabrication of Inconel 690 claddings on 316 L stainless-steel substrates. Also, irregular 2–3 μm diameter, low energy subgrains were formed along with dislocation densities varying from 108 to 109 cm^2, and a homogeneous distribution of Cr_(23)C_6 precipitates. Precipitates were formed within the grains(with ~3 μm interparticle spacing),but not in the subgrain or columnar grain boundaries. These inclusive, hierarchical microstructures produced a tensile yield strength of 0.527 GPa, elongation of 21%, and Vickers microindentation hardness of 2.33 GPa for the Inconel 690 cladding in contrast to a tensile yield strength of 0.327 GPa, elongation of 53%, and Vickers microindentation hardness of 1.78 GPa, respectively for the wrought 316 L stainlesssteel substrate. Aging of both the Inconel 690 cladding and the 316 L stainless-steel substrate at 685?C for50 h precipitated Cr_(23)C_6 carbides in the Inconel 690 columnar grain boundaries, but not in the low-angle(and low energy) subgrain boundaries. In contrast, Cr_(23)C_6 carbides precipitated in the 316 L stainless-steel grain boundaries, but not in the low energy coherent {111} twin boundaries. Consequently
