A novel amidoxime-based fibrous adsorbent,denoted as PE/PP-g-(PAAc-co-PAO), was prepared by preirradiation grafting of acrylic acid and acrylonitrile onto polyethylene-coated polypropylene skin-core(PE/PP)fibers using...A novel amidoxime-based fibrous adsorbent,denoted as PE/PP-g-(PAAc-co-PAO), was prepared by preirradiation grafting of acrylic acid and acrylonitrile onto polyethylene-coated polypropylene skin-core(PE/PP)fibers using 60 Co γ-ray irradiation, followed by amidoximation. The original and modified PE/PP fibers were characterized by a series of characterization methods to demonstrate the attachment of amidoxime groups onto the PE/PP fibers. Breaking strength tests confirmed that the fibrous adsorbent could maintain good mechanical properties. The adsorption capacity of the PE/PP-g-(PAAc-coPAO) fibers was investigated in simulated seawater with an initial uranium concentration of 330 μg/L. The uranium adsorption capacity was 2.27 mg/g-adsorbent after 24 h in simulated seawater, and the equilibrium data were well described by the Freundlich isotherm model. The PE/PP-g-(PAAc-co-PAO) adsorbent exhibited good regeneration and recyclability during five adsorption-desorption cycles.The adsorption test was also performed in simulated radioactive effluents with uranium concentrations of 10 and100 μg/L. The effect of the pH value on the adsorption capacity was also studied. At a very low initial concentration 10 μg/L solution, the PE/PP-g-(PAAc-co-PAO)fiber could remove as much as 93.0% of the uranium, and up to 71.2% of the uranium in the simulated radioactive effluent. These results indicated that the PE/PP-g-(PAAcco-PAO) adsorbent could be used in radioactive effluents over a wide range of pH values. Therefore, the PE/PP-g-(PAAc-co-PAO) fibers, with their high uranium selectivity,good regeneration and recyclability,good mechanical properties, and low cost, are promising adsorbents for extracting uranium from aqueous solutions.展开更多
Radiation induced graft polymerization on polymeric matrix followed by functionalization is widely accepted for the preparation of metal adsorbents. In this paper, a pre-irradiation method was used for emulsion graft ...Radiation induced graft polymerization on polymeric matrix followed by functionalization is widely accepted for the preparation of metal adsorbents. In this paper, a pre-irradiation method was used for emulsion graft polymerization of 4-hydroxybutyl acrylate glycidylether (4-HB) onto polyethylene/polypropylene (PE/PP) nonwoven fabric. The degree of grafting (Dg) which can be calculated by weight increment was determined as a function of reaction time, irradiation dose, and monomer concentration. After 30 kGy irradiation, with 4-HB concentration of 5%, surfactant Span 20 of 0.5% at 40°C for 2 h, the trunk polymer was made grafted at a Dg of 135%. 4-HB-grafted PE/PP nonwoven fabric was modified by ethylenediamine (EDA) in isopropyl alcohol (IPA) as a solvent at 60°C. With a Dg of 135%, the amine group density of the adsorbent is 2.8 mmol/g. The adsorption test was carried out by batch experiment in several metal ion solutions, and the removal ratio from the EDA modified adsorbent of the metal ions is in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+ > Li+. Compared with glycidyl methacrylate (GMA) which is a typical functional monomer for graft polymerization, 4-HB-grafted adsorbent exhibited not only better mechanical property but also higher adsorption capacity of Cu2+ and Pb2+.展开更多
基金supported by the National Natural Science Foundation of China(Nos.U1732151 and 21676291)Strategic Pilot and Technology Special Funds of the Chinese Academy of Science(No.XDA02030200)
文摘A novel amidoxime-based fibrous adsorbent,denoted as PE/PP-g-(PAAc-co-PAO), was prepared by preirradiation grafting of acrylic acid and acrylonitrile onto polyethylene-coated polypropylene skin-core(PE/PP)fibers using 60 Co γ-ray irradiation, followed by amidoximation. The original and modified PE/PP fibers were characterized by a series of characterization methods to demonstrate the attachment of amidoxime groups onto the PE/PP fibers. Breaking strength tests confirmed that the fibrous adsorbent could maintain good mechanical properties. The adsorption capacity of the PE/PP-g-(PAAc-coPAO) fibers was investigated in simulated seawater with an initial uranium concentration of 330 μg/L. The uranium adsorption capacity was 2.27 mg/g-adsorbent after 24 h in simulated seawater, and the equilibrium data were well described by the Freundlich isotherm model. The PE/PP-g-(PAAc-co-PAO) adsorbent exhibited good regeneration and recyclability during five adsorption-desorption cycles.The adsorption test was also performed in simulated radioactive effluents with uranium concentrations of 10 and100 μg/L. The effect of the pH value on the adsorption capacity was also studied. At a very low initial concentration 10 μg/L solution, the PE/PP-g-(PAAc-co-PAO)fiber could remove as much as 93.0% of the uranium, and up to 71.2% of the uranium in the simulated radioactive effluent. These results indicated that the PE/PP-g-(PAAcco-PAO) adsorbent could be used in radioactive effluents over a wide range of pH values. Therefore, the PE/PP-g-(PAAc-co-PAO) fibers, with their high uranium selectivity,good regeneration and recyclability,good mechanical properties, and low cost, are promising adsorbents for extracting uranium from aqueous solutions.
文摘Radiation induced graft polymerization on polymeric matrix followed by functionalization is widely accepted for the preparation of metal adsorbents. In this paper, a pre-irradiation method was used for emulsion graft polymerization of 4-hydroxybutyl acrylate glycidylether (4-HB) onto polyethylene/polypropylene (PE/PP) nonwoven fabric. The degree of grafting (Dg) which can be calculated by weight increment was determined as a function of reaction time, irradiation dose, and monomer concentration. After 30 kGy irradiation, with 4-HB concentration of 5%, surfactant Span 20 of 0.5% at 40°C for 2 h, the trunk polymer was made grafted at a Dg of 135%. 4-HB-grafted PE/PP nonwoven fabric was modified by ethylenediamine (EDA) in isopropyl alcohol (IPA) as a solvent at 60°C. With a Dg of 135%, the amine group density of the adsorbent is 2.8 mmol/g. The adsorption test was carried out by batch experiment in several metal ion solutions, and the removal ratio from the EDA modified adsorbent of the metal ions is in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+ > Li+. Compared with glycidyl methacrylate (GMA) which is a typical functional monomer for graft polymerization, 4-HB-grafted adsorbent exhibited not only better mechanical property but also higher adsorption capacity of Cu2+ and Pb2+.
