In this study, the effects of main welding parameters （rotation speed （ω） and welding speed （υ）） on the microstructure, micro-hardness distribution and tensile properties of friction stir welded （FSW） 2195-T...In this study, the effects of main welding parameters （rotation speed （ω） and welding speed （υ）） on the microstructure, micro-hardness distribution and tensile properties of friction stir welded （FSW） 2195-T8 Al-Li alloy were investigated. The effects of T6 post-treatments at different solution and aging conditions on the mechanical properties and microstructure characteristics of the FSW joints were also investigated. The results show that with increasing to and v, both strength and elongation of the joints increase first, and then decrease with further increase of ω and υ. All the joints under varied welding parameters show significant strength loss, and the strength reaches only 65% of the base metal, The effect of T6 post-heat treatment on the mechanical properties of the joints depends on the solution and aging conditions. Two heat treatment processes （480 ℃×0.5 h quenching＋ 180 ℃× 12 h, 520 ℃× 0.5 h quenching＋ 180 ℃×12h aging） are found to increase the joint strength. Furthermore, low temperature quenching （480℃） is more beneficial to the joint strength. The joint strength can reach 85% of the base metal. Whereas both low temperature aging （140 ℃× 56h） and stepped aging （ 100 ℃× 12 h ＋ 180 ℃× 3 h） processes decrease the joint strength. After heat treatment all the joints show decreased ductility due to the obvious grain coarsening in the nugget zone （NZ） and thermo-mechanically affected zone （TMAZ）.展开更多
AA2219 aluminium alloy joints were fabricated by variable polarity tungsten inert gas （VPTIG） welding process and the effects of post weld heat treatment （PWHT） on the tensile properties, microstructure and fatigu...AA2219 aluminium alloy joints were fabricated by variable polarity tungsten inert gas （VPTIG） welding process and the effects of post weld heat treatment （PWHT） on the tensile properties, microstructure and fatigue behaviour of the welded joints were investigated. The VPTIG welding process was adopted because it could meet the need of cathode cleaning and meanwhile it could reduce the deterioration of tungsten electrode furthest. The welded samples were divided into as-welded （AW） sample and PWHT sample. The PWHT method used on the samples was solution treatment （535 ℃, 30 rain）, water quenching and artificial aging （175 ℃, 12 h）. The experimental results show that, compared with the AW samples, the microstructure characteristics and mechanical properties of the AA2219 joints after PWHT were significantly improved. The improvement of yield strength, ultimate tensile strength, and fatigue strength are 42.6%, 43.1% and 18.4%, respectively.展开更多
6061 aluminum alloy T-joints were welded by double-pulsed MIG welding process. Then, the post-weld heat treatment was performed on the welded T-joints. The weld microstructure under different aging temperature and tim...6061 aluminum alloy T-joints were welded by double-pulsed MIG welding process. Then, the post-weld heat treatment was performed on the welded T-joints. The weld microstructure under different aging temperature and time was investigated by transmission electron microscopy and scanning electron microscopy. The mechanical properties were examined by hardness test and tensile test. The results showed that the micro-hardness was sensitive to heat treatment temperature and time. Increasing temperature was beneficial to the shortening of peak aging time. There were a large number of dislocations and few precipitates in the welded joints. With the increase of post-weld heat treatment temperature and time, the density of dislocation decreased. Meanwhile, the strengthening phase precipitated and grew up gradually. When the post-weld heat treatment temperature increased up to 200℃, large Q' phases were observed. And they were responsible for the peak value of the micro-hardness in the welded joints.展开更多
Ballistic behaviour of different zones of post-weld heat-treated(PWHT)magnesium alloy(AZ31B)target against 7.62 mm×39 mm armour-piercing(AP)projectile with a striking velocity of(430±20)m/s was determined.Ma...Ballistic behaviour of different zones of post-weld heat-treated(PWHT)magnesium alloy(AZ31B)target against 7.62 mm×39 mm armour-piercing(AP)projectile with a striking velocity of(430±20)m/s was determined.Magnesium alloy(AZ31B)welded joints were prepared by using friction stir welding(FSW)process and subjected to different heat treatment conditions.The microhardness values of non-heat-treated and heat-treated FSW joints were investigated.The results indicated that PWHT process(250°C,1 h)has improved the microhardness of heat-treated FSW joints.Scanning electron microscope(SEM)microstructure showed that heat treatment has caused the formation of fineα-Mg grains and tiny precipitates and made the dissolution ofβ-Mg17Al12 phase into the Mg matrix.The ballistic behaviour of PWHT zones was estimated by measuring the depth of penetration(DOP)of the projectile.Lower DOP value was observed for the base metal zone(BMZ)of a heat-treated welded joint.Post ballistic SEM examinations on the cross-section of all three zones of crater region showed the formation of adiabatic shear band(ASB).展开更多
High entropy alloys(HEAs)have superior mechanical properties that have enabled them to be used as structural materials in nuclear and aerospace applications.As a dissimilar joint design is required for these applicati...High entropy alloys(HEAs)have superior mechanical properties that have enabled them to be used as structural materials in nuclear and aerospace applications.As a dissimilar joint design is required for these applications,we created a dissimilar joint between CoCrFeMnNi-HEA and duplex stainless steel(DSS)through laser beam welding;a technique capable of producing a sound joint between the two materials.Micro structure examination using SEM/EBSD/XRD analysis revealed that the weld metal(WM)exhibits an FCC phase regardless of the postweld heat treatment(PWHT)temperature(800 and 1000℃)without forming detrimental intermetallic compounds or microsegregation.The heat-affected zone of the CoCrFeMnNi-HEA showed CrMn oxide inclusions while that of the DSS showed no inclusions.Moreover,a lower hardness was recorded by the WM compared to the base metal after welding.After PWHT,the hardness of the WM,CoCrFeMnNi-HEA,and DSS decreased with an increase in the PWHT temperature.However,the decrease in the hardness of the HEA was more significant than in the WM and DSS.The cause for this reduction in hardness was attributed to recrystallization and grain growth.In addition,a strength of 584 MPa with low ductility was recorded after welding.The obtained strength was lower than that of the BMs,but comparable to that of the welded CoCrFeMnNi-HEA.The application of PWHT resulted in over a 20%increment in ductility,with only a marginal reduction in strength.The defo rmation mechanism in the as-weld joint was mainly dominated by dislocation while that for the PWHT joint was twinning.We propose laser beam offset welding as a technique to improve the mechanical properties of the dissimilar joint,which will be the subject of future studies.展开更多
Magnesium(Mg)and its alloys are emerging as a structural material for the aerospace,automobile,and electronics industries,driven by the imperative of weight reduction.They are also drawing notable attention in the med...Magnesium(Mg)and its alloys are emerging as a structural material for the aerospace,automobile,and electronics industries,driven by the imperative of weight reduction.They are also drawing notable attention in the medical industries owing to their biodegradability and a lower elastic modulus comparable to bone.The ability to manufacture near-net shape products featuring intricate geometries has sparked huge interest in additive manufacturing(AM)of Mg alloys,reflecting a transformation in the manufacturing sectors.However,AM of Mg alloys presents more formidable challenges due to inherent properties,particularly susceptibility to oxidation,gas trapping,high thermal expansion coefficient,and low solidification temperature.This leads to defects such as porosity,lack of fusion,cracking,delamination,residual stresses,and inhomogeneity,ultimately influencing the mechanical,corrosion,and surface properties of AM Mg alloys.To address these issues,post-processing of AM Mg alloys are often needed to make them suitable for application.The present article reviews all post-processing techniques adapted for AM Mg alloys to date,including heat treatment,hot isostatic pressing,friction stir processing,and surface peening.The utilization of these methods within the hybrid AM process,employing interlayer post-processing,is also discussed.Optimal post-processing conditions are reported,and their influence on the microstructure,mechanical,and corrosion properties are detailed.Additionally,future prospects and research directions are proposed.展开更多
The high corrosion sensitivity and the potential bio-toxicity of Mg-Ag alloys limit their wide applications for the production of implanted devices. In the present work, Mn is added into the Mg-Ag alloy to optimize it...The high corrosion sensitivity and the potential bio-toxicity of Mg-Ag alloys limit their wide applications for the production of implanted devices. In the present work, Mn is added into the Mg-Ag alloy to optimize its corrosion behaviour. The corrosion behaviour of Mg-Ag-Mn alloys is investigated with the underlying microstructural factors examined. The Mg-Ag alloy with 2 wt% Mn exhibits the highest corrosion resistance after post-casting heat treatment at 440 ℃. The addition of Mn results in α-Mn phase with the incorporation of Fe, which suppresses the cathodic activity of impurity Fe. Further, heat treatment of the cast alloys homogenizes the distribution of Ag and promotes the precipitation of α-Mn phase. The former removes Ag segregations as potential cathodes;the latter promotes a more uniform distribution of cathodes and, therefore, prevents localized corrosion.展开更多
The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstru...The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstructure showed fine cell and columnar structure due to high cooling rate.Ti element segregation was observed in inter-cell/inter-columnar area.After post heat-treatment,the initially-observed cell structure disappeared,instead bimodal Ni_3(Al,Ti)particles formed.High temperature(1273 K and 1373 K)oxidation test results showed parabolic oxidation curves regardless of temperature and initial microstructure.The as-built IN738LC fabricated via the selective laser melting process displayed oxidation resistance similar to or slightly better than that of IN738LC fabricated via wrought or cast process.Heat-treated SLM IN738LC,although had similar oxidation weight-gain values to those of the SLM asbuilt material at 1273K,showed relatively better oxidation resistance at 1373 K.Bimodal Ni_3(Al,Ti)precipitate formed in the post heat treatment changed the local chemical composition,thereby led to changes in alumina former/chromia former location and fraction on the alloy surface.It was concluded that in heat-treated IN738LC increased alumina former fraction was found,and this resulted in excellent oxidation resistance and relatively low weight-gain.展开更多
The mechanical properties of Ti-23Al-17Nb (mole fraction,%) laser beam welding alloy joint at room temperature are comparable to that of the base materials.However,the strength and ductility of the as-welded joint det...The mechanical properties of Ti-23Al-17Nb (mole fraction,%) laser beam welding alloy joint at room temperature are comparable to that of the base materials.However,the strength and ductility of the as-welded joint deteriorate seriously after high temperature circulation.The effect of post-welded heat treatment on the microstructure and mechanical properties of the joint was investigated.The heat treatment was taken at 980 ℃ for 1.5 h,then furnace cooling and air cooling were performed separately.The results indicate that proper post-welded heat treatment improves the ductility of the joint at high temperature.展开更多
Direct friction welding of Ti Al alloy to 40 Cr steel rods was conducted, and the microstructure and mechanical properties of the resultant joints in as-welded and post-weld heat treatment（PWHT） states were investig...Direct friction welding of Ti Al alloy to 40 Cr steel rods was conducted, and the microstructure and mechanical properties of the resultant joints in as-welded and post-weld heat treatment（PWHT） states were investigated. The martensitic transformation occurred and brittle Ti C phase formed near the interface due to C agglomeration, which degraded the joint strength and increased the microhardness at the interface in as-welded state. Feathery and Widmanstatten structure generated near the interface on Ti Al alloy side. After PWHT at 580 °C and 630 °C for 2 h, the sorbite formed and C dispersed at the interface, leading to the increase of the joint strength from 86 MPa in as-welded state to 395 MPa and 330 MPa, respectively. The heat-treated specimen fractured with quasi-cleavage features through the zone 1 mm away from the interface on TiA l alloy side, but the as-welded specimen failed through the interface.展开更多
基金supported by the National Natural Science Foundation of China(No.51305272)
文摘In this study, the effects of main welding parameters （rotation speed （ω） and welding speed （υ）） on the microstructure, micro-hardness distribution and tensile properties of friction stir welded （FSW） 2195-T8 Al-Li alloy were investigated. The effects of T6 post-treatments at different solution and aging conditions on the mechanical properties and microstructure characteristics of the FSW joints were also investigated. The results show that with increasing to and v, both strength and elongation of the joints increase first, and then decrease with further increase of ω and υ. All the joints under varied welding parameters show significant strength loss, and the strength reaches only 65% of the base metal, The effect of T6 post-heat treatment on the mechanical properties of the joints depends on the solution and aging conditions. Two heat treatment processes （480 ℃×0.5 h quenching＋ 180 ℃× 12 h, 520 ℃× 0.5 h quenching＋ 180 ℃×12h aging） are found to increase the joint strength. Furthermore, low temperature quenching （480℃） is more beneficial to the joint strength. The joint strength can reach 85% of the base metal. Whereas both low temperature aging （140 ℃× 56h） and stepped aging （ 100 ℃× 12 h ＋ 180 ℃× 3 h） processes decrease the joint strength. After heat treatment all the joints show decreased ductility due to the obvious grain coarsening in the nugget zone （NZ） and thermo-mechanically affected zone （TMAZ）.
基金Project(51275343)supported by the National Natural Science Foundation of China
文摘AA2219 aluminium alloy joints were fabricated by variable polarity tungsten inert gas （VPTIG） welding process and the effects of post weld heat treatment （PWHT） on the tensile properties, microstructure and fatigue behaviour of the welded joints were investigated. The VPTIG welding process was adopted because it could meet the need of cathode cleaning and meanwhile it could reduce the deterioration of tungsten electrode furthest. The welded samples were divided into as-welded （AW） sample and PWHT sample. The PWHT method used on the samples was solution treatment （535 ℃, 30 rain）, water quenching and artificial aging （175 ℃, 12 h）. The experimental results show that, compared with the AW samples, the microstructure characteristics and mechanical properties of the AA2219 joints after PWHT were significantly improved. The improvement of yield strength, ultimate tensile strength, and fatigue strength are 42.6%, 43.1% and 18.4%, respectively.
基金Projects(2019JJ70077,2019JJ50510) supported by the National Science Foundation of Hunan Province,ChinaProject(31665004) supported by Open Fund of State Key Laboratory of Advanced Design and Manufacture for Vehicle Body,ChinaProjects(18B552,18B285) supported by Scientific Research Fund of Hunan Provincial Education Department,China
文摘6061 aluminum alloy T-joints were welded by double-pulsed MIG welding process. Then, the post-weld heat treatment was performed on the welded T-joints. The weld microstructure under different aging temperature and time was investigated by transmission electron microscopy and scanning electron microscopy. The mechanical properties were examined by hardness test and tensile test. The results showed that the micro-hardness was sensitive to heat treatment temperature and time. Increasing temperature was beneficial to the shortening of peak aging time. There were a large number of dislocations and few precipitates in the welded joints. With the increase of post-weld heat treatment temperature and time, the density of dislocation decreased. Meanwhile, the strengthening phase precipitated and grew up gradually. When the post-weld heat treatment temperature increased up to 200℃, large Q' phases were observed. And they were responsible for the peak value of the micro-hardness in the welded joints.
文摘Ballistic behaviour of different zones of post-weld heat-treated(PWHT)magnesium alloy(AZ31B)target against 7.62 mm×39 mm armour-piercing(AP)projectile with a striking velocity of(430±20)m/s was determined.Magnesium alloy(AZ31B)welded joints were prepared by using friction stir welding(FSW)process and subjected to different heat treatment conditions.The microhardness values of non-heat-treated and heat-treated FSW joints were investigated.The results indicated that PWHT process(250°C,1 h)has improved the microhardness of heat-treated FSW joints.Scanning electron microscope(SEM)microstructure showed that heat treatment has caused the formation of fineα-Mg grains and tiny precipitates and made the dissolution ofβ-Mg17Al12 phase into the Mg matrix.The ballistic behaviour of PWHT zones was estimated by measuring the depth of penetration(DOP)of the projectile.Lower DOP value was observed for the base metal zone(BMZ)of a heat-treated welded joint.Post ballistic SEM examinations on the cross-section of all three zones of crater region showed the formation of adiabatic shear band(ASB).
基金financially supported by a grant from the National Research Foundation of Korea(NRF)funded by the Korean government(MSIT)(No.2021R1A2B5B01002063)。
文摘High entropy alloys(HEAs)have superior mechanical properties that have enabled them to be used as structural materials in nuclear and aerospace applications.As a dissimilar joint design is required for these applications,we created a dissimilar joint between CoCrFeMnNi-HEA and duplex stainless steel(DSS)through laser beam welding;a technique capable of producing a sound joint between the two materials.Micro structure examination using SEM/EBSD/XRD analysis revealed that the weld metal(WM)exhibits an FCC phase regardless of the postweld heat treatment(PWHT)temperature(800 and 1000℃)without forming detrimental intermetallic compounds or microsegregation.The heat-affected zone of the CoCrFeMnNi-HEA showed CrMn oxide inclusions while that of the DSS showed no inclusions.Moreover,a lower hardness was recorded by the WM compared to the base metal after welding.After PWHT,the hardness of the WM,CoCrFeMnNi-HEA,and DSS decreased with an increase in the PWHT temperature.However,the decrease in the hardness of the HEA was more significant than in the WM and DSS.The cause for this reduction in hardness was attributed to recrystallization and grain growth.In addition,a strength of 584 MPa with low ductility was recorded after welding.The obtained strength was lower than that of the BMs,but comparable to that of the welded CoCrFeMnNi-HEA.The application of PWHT resulted in over a 20%increment in ductility,with only a marginal reduction in strength.The defo rmation mechanism in the as-weld joint was mainly dominated by dislocation while that for the PWHT joint was twinning.We propose laser beam offset welding as a technique to improve the mechanical properties of the dissimilar joint,which will be the subject of future studies.
文摘Magnesium(Mg)and its alloys are emerging as a structural material for the aerospace,automobile,and electronics industries,driven by the imperative of weight reduction.They are also drawing notable attention in the medical industries owing to their biodegradability and a lower elastic modulus comparable to bone.The ability to manufacture near-net shape products featuring intricate geometries has sparked huge interest in additive manufacturing(AM)of Mg alloys,reflecting a transformation in the manufacturing sectors.However,AM of Mg alloys presents more formidable challenges due to inherent properties,particularly susceptibility to oxidation,gas trapping,high thermal expansion coefficient,and low solidification temperature.This leads to defects such as porosity,lack of fusion,cracking,delamination,residual stresses,and inhomogeneity,ultimately influencing the mechanical,corrosion,and surface properties of AM Mg alloys.To address these issues,post-processing of AM Mg alloys are often needed to make them suitable for application.The present article reviews all post-processing techniques adapted for AM Mg alloys to date,including heat treatment,hot isostatic pressing,friction stir processing,and surface peening.The utilization of these methods within the hybrid AM process,employing interlayer post-processing,is also discussed.Optimal post-processing conditions are reported,and their influence on the microstructure,mechanical,and corrosion properties are detailed.Additionally,future prospects and research directions are proposed.
基金supported by the National Natural Science Foundation of China(Nos.52001128 and 52371065)the Hubei Provincial Natural Science Foundation of China(No.2023AFB637).
文摘The high corrosion sensitivity and the potential bio-toxicity of Mg-Ag alloys limit their wide applications for the production of implanted devices. In the present work, Mn is added into the Mg-Ag alloy to optimize its corrosion behaviour. The corrosion behaviour of Mg-Ag-Mn alloys is investigated with the underlying microstructural factors examined. The Mg-Ag alloy with 2 wt% Mn exhibits the highest corrosion resistance after post-casting heat treatment at 440 ℃. The addition of Mn results in α-Mn phase with the incorporation of Fe, which suppresses the cathodic activity of impurity Fe. Further, heat treatment of the cast alloys homogenizes the distribution of Ag and promotes the precipitation of α-Mn phase. The former removes Ag segregations as potential cathodes;the latter promotes a more uniform distribution of cathodes and, therefore, prevents localized corrosion.
基金the Fundamental Research Program of the Korea Institute of Materials Science(Grant No.PNK5520)Korea Institute for Advancement of Technology(KIAT)grant funded by the Korea Government(MOTIE)(P0002007,The Competency Development Program for Industry Specialist)。
文摘The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstructure showed fine cell and columnar structure due to high cooling rate.Ti element segregation was observed in inter-cell/inter-columnar area.After post heat-treatment,the initially-observed cell structure disappeared,instead bimodal Ni_3(Al,Ti)particles formed.High temperature(1273 K and 1373 K)oxidation test results showed parabolic oxidation curves regardless of temperature and initial microstructure.The as-built IN738LC fabricated via the selective laser melting process displayed oxidation resistance similar to or slightly better than that of IN738LC fabricated via wrought or cast process.Heat-treated SLM IN738LC,although had similar oxidation weight-gain values to those of the SLM asbuilt material at 1273K,showed relatively better oxidation resistance at 1373 K.Bimodal Ni_3(Al,Ti)precipitate formed in the post heat treatment changed the local chemical composition,thereby led to changes in alumina former/chromia former location and fraction on the alloy surface.It was concluded that in heat-treated IN738LC increased alumina former fraction was found,and this resulted in excellent oxidation resistance and relatively low weight-gain.
文摘The mechanical properties of Ti-23Al-17Nb (mole fraction,%) laser beam welding alloy joint at room temperature are comparable to that of the base materials.However,the strength and ductility of the as-welded joint deteriorate seriously after high temperature circulation.The effect of post-welded heat treatment on the microstructure and mechanical properties of the joint was investigated.The heat treatment was taken at 980 ℃ for 1.5 h,then furnace cooling and air cooling were performed separately.The results indicate that proper post-welded heat treatment improves the ductility of the joint at high temperature.
基金Project(51374048)supported by the National Natural Science Foundation of ChinaProject(2011CB013402)supported by the National Basic Research Program of ChinaProject(AWPT-Z01)supported by the State Key Laboratory of Advanced Welding and Joining,China
文摘Direct friction welding of Ti Al alloy to 40 Cr steel rods was conducted, and the microstructure and mechanical properties of the resultant joints in as-welded and post-weld heat treatment（PWHT） states were investigated. The martensitic transformation occurred and brittle Ti C phase formed near the interface due to C agglomeration, which degraded the joint strength and increased the microhardness at the interface in as-welded state. Feathery and Widmanstatten structure generated near the interface on Ti Al alloy side. After PWHT at 580 °C and 630 °C for 2 h, the sorbite formed and C dispersed at the interface, leading to the increase of the joint strength from 86 MPa in as-welded state to 395 MPa and 330 MPa, respectively. The heat-treated specimen fractured with quasi-cleavage features through the zone 1 mm away from the interface on TiA l alloy side, but the as-welded specimen failed through the interface.
