The line pipe forming operation can be divided into two parts, first is to achieve the required shape in terms of curvature and ovality after formation of the line pipe. The curvature and ovality ultimately effects th...The line pipe forming operation can be divided into two parts, first is to achieve the required shape in terms of curvature and ovality after formation of the line pipe. The curvature and ovality ultimately effects the final dimensional controls at the later stage i.e. after mechanical expansion of the line pipe. The second part is to make right welding joint geometry to make the final long seam weld of line pipe. The welding joint geometry ultimately controls soundness of final seam weld at later stage i.e. during submerged arc welding of the line pipe. As far as curvature or shape of line pipe is concerned, important operation is making the required curvature along the edges of TMCP and ACC (Thermo mechanical controlled processing and accelerated cooling process) plate for line pipe (Plate Edge Crimping press) up to the 150 mm in width minimum and forming of the line pipe at J-C-O press. The selection of dies with proper hardness and curvature in both the operation plays a vital role in the formation of line pipes. The main parameters of selection dies (Tools) are size of line pipe for which dies/tools are to be made i.e. the diameter of line pipe, thickness of line pipe and most important is grade of line pipe (Strength level). The grade or strength level decides amount of spring back behavior of the steel Plate. The spring back behavior again varies from steel mill to steel mill in the same grade of HR plate. This is because the each steel mill has its own manufacturing procedures to produce the TMCP and ACC plate. The plate for line pipe is produced through TMCP (Thermo mechanical controlled processing) and accelerated cooling process. In this process the strength level is achieved by the chemical composition of the slab, thickness of the slab, reheating temperature, roughing temperature at which reduction in the thickness, finish rolling temperature and finally the accelerated cooling temperature rate.展开更多
3-Roller bending is a widely applied manufacturing process, particularly in structural steel pipe industry.However, due to the difficulty and high cost of measuring stress distribution inside sheet material via tradit...3-Roller bending is a widely applied manufacturing process, particularly in structural steel pipe industry.However, due to the difficulty and high cost of measuring stress distribution inside sheet material via traditional method,internal stress/strain response during forming is largely unexplored. The focuses of this study are two：（1） to map the radii of curvature as well as the stress inside the work piece during forming by utilizing the meshing mechanism of finite element method, and（2） to further provide some numeric guidelines for the configuration of the rolling system in order to improve production efficiency and product quality. The results of this study indicate that：（1） it is crucial to properly choose forming parameter in order to produce product with desired radii;（2） much like a gradual springback process, the radii of curvature gradually increase from the top roller to the exit-side bottom roller;（3） under the assumptions made in this study, to produce pipes with a specified diameter with varying configurations of the 3-roller system will not significantly change the final residual stress; and（4） finally, shifting of the neutral axis up to 2.0% of the thickness toward the compressing side during the forming process is observed.展开更多
文摘The line pipe forming operation can be divided into two parts, first is to achieve the required shape in terms of curvature and ovality after formation of the line pipe. The curvature and ovality ultimately effects the final dimensional controls at the later stage i.e. after mechanical expansion of the line pipe. The second part is to make right welding joint geometry to make the final long seam weld of line pipe. The welding joint geometry ultimately controls soundness of final seam weld at later stage i.e. during submerged arc welding of the line pipe. As far as curvature or shape of line pipe is concerned, important operation is making the required curvature along the edges of TMCP and ACC (Thermo mechanical controlled processing and accelerated cooling process) plate for line pipe (Plate Edge Crimping press) up to the 150 mm in width minimum and forming of the line pipe at J-C-O press. The selection of dies with proper hardness and curvature in both the operation plays a vital role in the formation of line pipes. The main parameters of selection dies (Tools) are size of line pipe for which dies/tools are to be made i.e. the diameter of line pipe, thickness of line pipe and most important is grade of line pipe (Strength level). The grade or strength level decides amount of spring back behavior of the steel Plate. The spring back behavior again varies from steel mill to steel mill in the same grade of HR plate. This is because the each steel mill has its own manufacturing procedures to produce the TMCP and ACC plate. The plate for line pipe is produced through TMCP (Thermo mechanical controlled processing) and accelerated cooling process. In this process the strength level is achieved by the chemical composition of the slab, thickness of the slab, reheating temperature, roughing temperature at which reduction in the thickness, finish rolling temperature and finally the accelerated cooling temperature rate.
基金the financial support provided by the LSU Graduate School through the Economic Development Award
文摘3-Roller bending is a widely applied manufacturing process, particularly in structural steel pipe industry.However, due to the difficulty and high cost of measuring stress distribution inside sheet material via traditional method,internal stress/strain response during forming is largely unexplored. The focuses of this study are two：（1） to map the radii of curvature as well as the stress inside the work piece during forming by utilizing the meshing mechanism of finite element method, and（2） to further provide some numeric guidelines for the configuration of the rolling system in order to improve production efficiency and product quality. The results of this study indicate that：（1） it is crucial to properly choose forming parameter in order to produce product with desired radii;（2） much like a gradual springback process, the radii of curvature gradually increase from the top roller to the exit-side bottom roller;（3） under the assumptions made in this study, to produce pipes with a specified diameter with varying configurations of the 3-roller system will not significantly change the final residual stress; and（4） finally, shifting of the neutral axis up to 2.0% of the thickness toward the compressing side during the forming process is observed.
