In this paper, a kind of fire new nonlinear integrator and integral action is proposed. Consequently, a conventional Proportional Nonlinear Integral (P_NI) observer and two kinds of added-order P_NI observers are deve...In this paper, a kind of fire new nonlinear integrator and integral action is proposed. Consequently, a conventional Proportional Nonlinear Integral (P_NI) observer and two kinds of added-order P_NI observers are developed to deal with the uncertain nonlinear system. The conditions on the observer gains to ensure the estimated error to be ultimate boundness, which shrinks to zero as the states and control inputs converge to the equilibrium point, are provided. This means that if the observed system is asymptotically stable, the estimated error dynamics is asymptotically stable, too. Moreover, the highlight point of this paper is that the design of nonlinear integral observer is achieved by linear system theory. Simulation results showed that under the normal and perturbed cases, the pure added-order P_NI observer can effectively deal with the uncertain nonlinearities on both the system dynamics and measured outputs.展开更多
Nonlinear friction is a dominant factor afecting the control accuracy of CNC machine tools.This paper proposes a friction pre-compensation method for CNC machine tools through constructing a nonlinear model predictive...Nonlinear friction is a dominant factor afecting the control accuracy of CNC machine tools.This paper proposes a friction pre-compensation method for CNC machine tools through constructing a nonlinear model predictive scheme.The nonlinear friction-induced tracking error is frstly modeled and then utilized to establish the nonlinear model predictive scheme,which is subsequently used to optimize the compensation signal by treating the friction-induced tracking error as the optimization objective.During the optimization procedure,the derivative of compensation signal is constrained to avoid vibration of machine tools.In contrast to other existing approaches,the proposed method only needs the parameters of Stribeck friction model and an additional tuning parameter,while fnely identifying the parameters related to the pre-sliding phenomenon is not required.As a result,it greatly facilitates the practical applicability.Both air cutting and real cutting experiments conducted on an in-house developed open-architecture CNC machine tool prove that the proposed method can reduce the tracking errors by more than 56%,and reduce the contour errors by more than 50%.展开更多
文摘In this paper, a kind of fire new nonlinear integrator and integral action is proposed. Consequently, a conventional Proportional Nonlinear Integral (P_NI) observer and two kinds of added-order P_NI observers are developed to deal with the uncertain nonlinear system. The conditions on the observer gains to ensure the estimated error to be ultimate boundness, which shrinks to zero as the states and control inputs converge to the equilibrium point, are provided. This means that if the observed system is asymptotically stable, the estimated error dynamics is asymptotically stable, too. Moreover, the highlight point of this paper is that the design of nonlinear integral observer is achieved by linear system theory. Simulation results showed that under the normal and perturbed cases, the pure added-order P_NI observer can effectively deal with the uncertain nonlinearities on both the system dynamics and measured outputs.
基金Supported by National Natural Science Foundation of China(Grant No.51975481)Fundamental Research Funds for the Central Universities of China(Grant No.D5000220061).
文摘Nonlinear friction is a dominant factor afecting the control accuracy of CNC machine tools.This paper proposes a friction pre-compensation method for CNC machine tools through constructing a nonlinear model predictive scheme.The nonlinear friction-induced tracking error is frstly modeled and then utilized to establish the nonlinear model predictive scheme,which is subsequently used to optimize the compensation signal by treating the friction-induced tracking error as the optimization objective.During the optimization procedure,the derivative of compensation signal is constrained to avoid vibration of machine tools.In contrast to other existing approaches,the proposed method only needs the parameters of Stribeck friction model and an additional tuning parameter,while fnely identifying the parameters related to the pre-sliding phenomenon is not required.As a result,it greatly facilitates the practical applicability.Both air cutting and real cutting experiments conducted on an in-house developed open-architecture CNC machine tool prove that the proposed method can reduce the tracking errors by more than 56%,and reduce the contour errors by more than 50%.
