A novel Al-14.1 Mg-0.47 Si-0.31 Sc-0.17 Zr alloy was applied in the printing process of selective laser melting(SLM),and the corresponding microstructural feature,phase identification,tensile properties and corrosion ...A novel Al-14.1 Mg-0.47 Si-0.31 Sc-0.17 Zr alloy was applied in the printing process of selective laser melting(SLM),and the corresponding microstructural feature,phase identification,tensile properties and corrosion behavior of the Al Mg Si Sc Zr alloy were studied in detail.As fabricated at 160 W and 200 mm/s,the Mg content of bulk sample decreased to 11.7 wt%due to the element vaporization at high energy density,and the density of this additively manufactured Al Mg Si Sc Zr alloy was 2.538 g/cm^(3),which is4.2%8.5%lighter than that of other SLM-processed Al alloys.After heat-treated(HT)at 325℃and 6 h,the microstructure was almost unchanged with an alternate distribution of fine equiaxed crystals and coarse columnar crystals.Nano-sized Al3(Sc,Zr)and Mg_(2)Si phases precipitated dispersedly in the Al matrix,and the tensile strength increased from 487.6 MPa to 578.4 MPa for precipitation strengthening and fine grain strengthening.With a fine grain size of 2.53μm,an excellent corrosion resistance was obtained for the as-printed(AP)Al Mg Si Sc Zr alloy.While the corrosion resistance of HT sample decreased slightly for the formation of non-dense oxide layer and pitting corrosion induced by diffuse precipitation distribution.This SLM-printed Al Mg Si Sc Zr alloy with high specific strength,good thermal stability and excellent corrosion resistance has broad prospects for the aerospace and automotive applications.展开更多
The microstructural evolution of pure nickel treated by deep rolling(DR)technique with different indent depths was investigated by means of optical microscopy and transmission electron microscopy.The surface roughness...The microstructural evolution of pure nickel treated by deep rolling(DR)technique with different indent depths was investigated by means of optical microscopy and transmission electron microscopy.The surface roughness,hardness and residual stress distribution along the depth from surface were measured.Moreover,the DR-treated sample was annealed at temperatures from 300 to 700℃for 2 h.The results reveal that dislocation movements are the fundamental mechanisms of gradient grain refinement during the DR process.With increasing indent depth of the DR,the gradient microhardness on the cross section of sample significantly increases,the maximum compressive residual stress decreases,and the affecting region of residual stress increases.The results of thermal stability depict that the microstructure can be stable as temperature up to 300℃,and the abnormal grain growth and annealing twins are observed at 600℃.展开更多
Microstructural stability of a nickel base single crystal alloy DD8 has been investigated.Standard heat treated specimen showed good microstructural stability at 950℃.While under the as-cast condition,a kind of rod-l...Microstructural stability of a nickel base single crystal alloy DD8 has been investigated.Standard heat treated specimen showed good microstructural stability at 950℃.While under the as-cast condition,a kind of rod-like phase precipitated in the interdendritic region of as-cast specimen during thermal exposure.The phase,which has bcc structure,was enriched with Cr.Thermo-calc also predicted precipitation of a bcc phase at around 950℃.The Cr-rich bcc phase was considered asα-Cr and formed due to the segregation of Cr under the as-cast condition.展开更多
文摘A novel Al-14.1 Mg-0.47 Si-0.31 Sc-0.17 Zr alloy was applied in the printing process of selective laser melting(SLM),and the corresponding microstructural feature,phase identification,tensile properties and corrosion behavior of the Al Mg Si Sc Zr alloy were studied in detail.As fabricated at 160 W and 200 mm/s,the Mg content of bulk sample decreased to 11.7 wt%due to the element vaporization at high energy density,and the density of this additively manufactured Al Mg Si Sc Zr alloy was 2.538 g/cm^(3),which is4.2%8.5%lighter than that of other SLM-processed Al alloys.After heat-treated(HT)at 325℃and 6 h,the microstructure was almost unchanged with an alternate distribution of fine equiaxed crystals and coarse columnar crystals.Nano-sized Al3(Sc,Zr)and Mg_(2)Si phases precipitated dispersedly in the Al matrix,and the tensile strength increased from 487.6 MPa to 578.4 MPa for precipitation strengthening and fine grain strengthening.With a fine grain size of 2.53μm,an excellent corrosion resistance was obtained for the as-printed(AP)Al Mg Si Sc Zr alloy.While the corrosion resistance of HT sample decreased slightly for the formation of non-dense oxide layer and pitting corrosion induced by diffuse precipitation distribution.This SLM-printed Al Mg Si Sc Zr alloy with high specific strength,good thermal stability and excellent corrosion resistance has broad prospects for the aerospace and automotive applications.
基金the financial support through the National Natural Science Foundation of China (Nos.51725503, 51605164 and 51575183)111 Project+4 种基金support by Shanghai Technology Innovation Program of SHEITC (CXY-2015-001)Fok Ying Tung Education FoundationYoung Program of Yangtze River Scholarssupport by Shanghai Sailing Program (16YF1402300)Shanghai Chenguang Program (16CG34)
文摘The microstructural evolution of pure nickel treated by deep rolling(DR)technique with different indent depths was investigated by means of optical microscopy and transmission electron microscopy.The surface roughness,hardness and residual stress distribution along the depth from surface were measured.Moreover,the DR-treated sample was annealed at temperatures from 300 to 700℃for 2 h.The results reveal that dislocation movements are the fundamental mechanisms of gradient grain refinement during the DR process.With increasing indent depth of the DR,the gradient microhardness on the cross section of sample significantly increases,the maximum compressive residual stress decreases,and the affecting region of residual stress increases.The results of thermal stability depict that the microstructure can be stable as temperature up to 300℃,and the abnormal grain growth and annealing twins are observed at 600℃.
文摘Microstructural stability of a nickel base single crystal alloy DD8 has been investigated.Standard heat treated specimen showed good microstructural stability at 950℃.While under the as-cast condition,a kind of rod-like phase precipitated in the interdendritic region of as-cast specimen during thermal exposure.The phase,which has bcc structure,was enriched with Cr.Thermo-calc also predicted precipitation of a bcc phase at around 950℃.The Cr-rich bcc phase was considered asα-Cr and formed due to the segregation of Cr under the as-cast condition.
