在半连续铸造过程中施加超声,成功制备了Φ1250 mm 2219铝合金铸锭.利用光学显微镜、扫描电镜、能谱仪及直读光谱仪等仪器对铸锭的组织与成分分布进行检测与分析,探究超声对铸锭组织与偏析的内在作用机制.研究结果表明:超声振动引起的...在半连续铸造过程中施加超声,成功制备了Φ1250 mm 2219铝合金铸锭.利用光学显微镜、扫描电镜、能谱仪及直读光谱仪等仪器对铸锭的组织与成分分布进行检测与分析,探究超声对铸锭组织与偏析的内在作用机制.研究结果表明:超声振动引起的空化和声流效应能明显均匀组织结构,细化晶粒,尤其是心部晶粒细化率达到39.6%.超声促进铸锭晶间第二相呈枝丫状断续分布,晶内析出物点状弥散分布.同时,超声有效减小近表面负偏析,降低边部与心部之间的溶质浓度差异,弱化整个横截面的浓度波动,从而改善宏观偏析.展开更多
The grain refinement and macrosegregation control of GCrl5 bearing steel were investigated under a type of rarely-used electromagnetic stirring, vertical electromagnetic stirring （V-EMS）, in continuous casting. V-EM...The grain refinement and macrosegregation control of GCrl5 bearing steel were investigated under a type of rarely-used electromagnetic stirring, vertical electromagnetic stirring （V-EMS）, in continuous casting. V-EMS can create an upward electromagnetic force and generate longitudinal loop convection, which ena- bles the better mixing of the upper part with the lower part of the liquid steel. The results showed that ap- plying V-EMS can enlarge the region of the equiaxed grain, decrease the secondary dendrite arm spacing （SDAS） and reduce the segregation of both carbon and sulfur. After applying V-EMS, liquid steel with a high solute concentration is brought to the dendrite tips, making the dendrite arms partially melt. The length of the dendrite fragment is approximately 1.8 mm, 10 to 12 times the SDAS. Upon increasing the amount of cooling water from 2.0 to 3.5 m3/h, the dendrite fragments exhibit an obvious aggregation fol- lowing V-EMS. Finally, a criterion for dendrite fragmentation under V-EMS was derived based on the dendrite fragmentation theory of Campanella et al.展开更多
New theories and technology in the electromagnetic field were put forward about DC casting of Al alloys, including the fundamental research works, i.e, effects of the electromagnetic field on solidus and liquidus, mac...New theories and technology in the electromagnetic field were put forward about DC casting of Al alloys, including the fundamental research works, i.e, effects of the electromagnetic field on solidus and liquidus, macrosegregation of the main alloying elements, microstructures, content of alloying elements in grains and grain size after solidification under electromagnetic field, and also including a new process DC casting under low frequency electromagnetic field(LFEMC), which can refine microstructure, eliminate macrosegregation, increase the content of alloying elements within grains, decrease the residual stress, avoid cracks and improve surface quality, and another new process DC casting under low frequency electromagnetic vibration(LFEVC), which is a high effective method for grain refining.展开更多
The influences of superheat and cooling intensity on macrostructure and macrosegregation of one new kind duplex stainless steel(DSS)were studied.Thermal simulation equipment was applied to prepare samples,which could ...The influences of superheat and cooling intensity on macrostructure and macrosegregation of one new kind duplex stainless steel(DSS)were studied.Thermal simulation equipment was applied to prepare samples,which could reproduce the industrial processes of DSS manufactured by a vertical continuous slab caster.Macrostructure and macrosegregation were analyzed using the digital single lens reflex and laser-induced breakdown spectroscope(LIBSOPA-200),respectively.The percentage of both chill zone and center equiaxed zone increases with the superheat decreasing,while that of the columnar zone decreases.There is only equiaxed grain existing as the superheat is 10 and 20℃.The lower the superheat is,the coarser the gain size is.High cooling intensity in mold could remarkably decrease the chill zone length and refine the grains in chill zone and center equiaxed zone.The influences of cooling intensity on macrosegregation are greater than those of superheat.The macrosegregation of Si,Mn and Cr is slightly dependent on superheat,while that of Cu,Mo and Ni changes greatly with superheat increasing.展开更多
A new approach to applying the electric current pulse （ECP） with parallel electrodes to the promotion of the transition from columnar crystal to equiaxed crystal and the improvement of macrosegregation was introduce...A new approach to applying the electric current pulse （ECP） with parallel electrodes to the promotion of the transition from columnar crystal to equiaxed crystal and the improvement of macrosegregation was introduced. The ECP was applied to different stages of the solidification. The results showed that the application of the ECP in both the initial stage （the thickness of solidified shell reached 2 mm approximately） and the late stage （the thickness of solidified shell reached 14 mm approximately） of solidification can promote the columnar to equiaxed transition （CET）. The analysis showed that during solidification, a large number of nuclei around the upper surface fell off due to ECP, which subsequently showered on the melt and impinged the growth front of the columnar crystal. Therefore, the CEToccurred. In addition, this method was also employed to influence the solidification process of bearing steel, and the results showed that the structure was changed from columnar crystal to equiaxed crystal, indicating that ECP can enhance the homogeneity of structure and composition of bearing steel.展开更多
The effect of electromagnetic field on macrosegregation of continuous casting aluminum alloy was studied. 7075 aluminum alloy ingot with diameter of 200 mm was produced by electromagnetic casting. Magnitude of coil cu...The effect of electromagnetic field on macrosegregation of continuous casting aluminum alloy was studied. 7075 aluminum alloy ingot with diameter of 200 mm was produced by electromagnetic casting. Magnitude of coil current was varied from 100 A to 600 A, and frequency from 10 Hz to 100 Hz. Variation of element content along the radius of ingot was examined by means of chemical analysis. The results show that electromagnetic casting process can effectively reduce the macrosegregation, and electromagnetic frequency has a great influence on element distribution along the radius of ingot. When frequency is 30 Hz, macrosegregation is eliminated completely.展开更多
文摘在半连续铸造过程中施加超声,成功制备了Φ1250 mm 2219铝合金铸锭.利用光学显微镜、扫描电镜、能谱仪及直读光谱仪等仪器对铸锭的组织与成分分布进行检测与分析,探究超声对铸锭组织与偏析的内在作用机制.研究结果表明:超声振动引起的空化和声流效应能明显均匀组织结构,细化晶粒,尤其是心部晶粒细化率达到39.6%.超声促进铸锭晶间第二相呈枝丫状断续分布,晶内析出物点状弥散分布.同时,超声有效减小近表面负偏析,降低边部与心部之间的溶质浓度差异,弱化整个横截面的浓度波动,从而改善宏观偏析.
基金supported by the National Natural Science Foundation of China(No.50834009)the Key Project of the Ministry of Education of China(No.311014)the 111 Project of China(No.B07015)
文摘The grain refinement and macrosegregation control of GCrl5 bearing steel were investigated under a type of rarely-used electromagnetic stirring, vertical electromagnetic stirring （V-EMS）, in continuous casting. V-EMS can create an upward electromagnetic force and generate longitudinal loop convection, which ena- bles the better mixing of the upper part with the lower part of the liquid steel. The results showed that ap- plying V-EMS can enlarge the region of the equiaxed grain, decrease the secondary dendrite arm spacing （SDAS） and reduce the segregation of both carbon and sulfur. After applying V-EMS, liquid steel with a high solute concentration is brought to the dendrite tips, making the dendrite arms partially melt. The length of the dendrite fragment is approximately 1.8 mm, 10 to 12 times the SDAS. Upon increasing the amount of cooling water from 2.0 to 3.5 m3/h, the dendrite fragments exhibit an obvious aggregation fol- lowing V-EMS. Finally, a criterion for dendrite fragmentation under V-EMS was derived based on the dendrite fragmentation theory of Campanella et al.
文摘New theories and technology in the electromagnetic field were put forward about DC casting of Al alloys, including the fundamental research works, i.e, effects of the electromagnetic field on solidus and liquidus, macrosegregation of the main alloying elements, microstructures, content of alloying elements in grains and grain size after solidification under electromagnetic field, and also including a new process DC casting under low frequency electromagnetic field(LFEMC), which can refine microstructure, eliminate macrosegregation, increase the content of alloying elements within grains, decrease the residual stress, avoid cracks and improve surface quality, and another new process DC casting under low frequency electromagnetic vibration(LFEVC), which is a high effective method for grain refining.
基金National Key Research and Development Program of China(No.2017YFB0701802)NSFC(Nos.51504148 and U1760204).
文摘The influences of superheat and cooling intensity on macrostructure and macrosegregation of one new kind duplex stainless steel(DSS)were studied.Thermal simulation equipment was applied to prepare samples,which could reproduce the industrial processes of DSS manufactured by a vertical continuous slab caster.Macrostructure and macrosegregation were analyzed using the digital single lens reflex and laser-induced breakdown spectroscope(LIBSOPA-200),respectively.The percentage of both chill zone and center equiaxed zone increases with the superheat decreasing,while that of the columnar zone decreases.There is only equiaxed grain existing as the superheat is 10 and 20℃.The lower the superheat is,the coarser the gain size is.High cooling intensity in mold could remarkably decrease the chill zone length and refine the grains in chill zone and center equiaxed zone.The influences of cooling intensity on macrosegregation are greater than those of superheat.The macrosegregation of Si,Mn and Cr is slightly dependent on superheat,while that of Cu,Mo and Ni changes greatly with superheat increasing.
基金Item Sponsored by National Natural Science Foundation of China(50674064,50734008)
文摘A new approach to applying the electric current pulse （ECP） with parallel electrodes to the promotion of the transition from columnar crystal to equiaxed crystal and the improvement of macrosegregation was introduced. The ECP was applied to different stages of the solidification. The results showed that the application of the ECP in both the initial stage （the thickness of solidified shell reached 2 mm approximately） and the late stage （the thickness of solidified shell reached 14 mm approximately） of solidification can promote the columnar to equiaxed transition （CET）. The analysis showed that during solidification, a large number of nuclei around the upper surface fell off due to ECP, which subsequently showered on the melt and impinged the growth front of the columnar crystal. Therefore, the CEToccurred. In addition, this method was also employed to influence the solidification process of bearing steel, and the results showed that the structure was changed from columnar crystal to equiaxed crystal, indicating that ECP can enhance the homogeneity of structure and composition of bearing steel.
文摘The effect of electromagnetic field on macrosegregation of continuous casting aluminum alloy was studied. 7075 aluminum alloy ingot with diameter of 200 mm was produced by electromagnetic casting. Magnitude of coil current was varied from 100 A to 600 A, and frequency from 10 Hz to 100 Hz. Variation of element content along the radius of ingot was examined by means of chemical analysis. The results show that electromagnetic casting process can effectively reduce the macrosegregation, and electromagnetic frequency has a great influence on element distribution along the radius of ingot. When frequency is 30 Hz, macrosegregation is eliminated completely.
