The present study fabricated a series of capillary wicks for loop heat pipes (LHPs), using two different methods, the cold-pressing sintering and direct loose sintering, and experimentally investigated the effect of d...The present study fabricated a series of capillary wicks for loop heat pipes (LHPs), using two different methods, the cold-pressing sintering and direct loose sintering, and experimentally investigated the effect of different methods, compositions and sintering parameters on their properties in terms of porosity, permeability and pore radius. Porosity and pore radius were measured by the Archimedes method and Scanning Electron Microscope (SEM), respectively. Permeability of the wicks was compared by calculation using empirical equation. Results show that capillary wicks were successfully fabricated by using two different methods; the optimal capillary wick was found to be sintered at 650°C for 30 min, using direct loose sintering technique, with 90% nickel and 10% copper. The wicks could reach the porosity of 70.07% and the permeability of 10?13 m2 order, with mean pore radius of 0.54 μm.展开更多
The operating instability of a dual compensation chamber loop heat pipe (DCC-LHP) including temperature hysteresis, reverse flow and temperature oscillation is described and explained in this paper. Test results indic...The operating instability of a dual compensation chamber loop heat pipe (DCC-LHP) including temperature hysteresis, reverse flow and temperature oscillation is described and explained in this paper. Test results indicate that the steady state operating temperature under the variable conductance mode is not the same during the power cycle tests with the same heat load, and it is lower during the power reduction cycle than that during the power increase cycle. Orientation has an effect on the heat load range when temperature hysteresis occurs, and the effect of power variation amplitude can be ignored. Reverse flow tends to occur in some of the startups at low heat loads, even if vapor existed in the vapor grooves initially, which is caused by a higher pressure inside the wick due to evaporation in the evaporator core or vapor penetration into it. Temperature oscillation tends to occur in some of the startups at low head loads or some steady-state operations at high heat loads. Especially when the compensation chamber with the bayonet through is above the evaporator, the incidence rate of temperature oscillation is high.展开更多
基金Supported by Shandong Provincial Program of Science and Technology Develop-ment(Grant No.2007GG1HZ06004)
文摘The present study fabricated a series of capillary wicks for loop heat pipes (LHPs), using two different methods, the cold-pressing sintering and direct loose sintering, and experimentally investigated the effect of different methods, compositions and sintering parameters on their properties in terms of porosity, permeability and pore radius. Porosity and pore radius were measured by the Archimedes method and Scanning Electron Microscope (SEM), respectively. Permeability of the wicks was compared by calculation using empirical equation. Results show that capillary wicks were successfully fabricated by using two different methods; the optimal capillary wick was found to be sintered at 650°C for 30 min, using direct loose sintering technique, with 90% nickel and 10% copper. The wicks could reach the porosity of 70.07% and the permeability of 10?13 m2 order, with mean pore radius of 0.54 μm.
基金Supported by the National Natural Science Foundation of China (Grant No. 50676006)
文摘The operating instability of a dual compensation chamber loop heat pipe (DCC-LHP) including temperature hysteresis, reverse flow and temperature oscillation is described and explained in this paper. Test results indicate that the steady state operating temperature under the variable conductance mode is not the same during the power cycle tests with the same heat load, and it is lower during the power reduction cycle than that during the power increase cycle. Orientation has an effect on the heat load range when temperature hysteresis occurs, and the effect of power variation amplitude can be ignored. Reverse flow tends to occur in some of the startups at low heat loads, even if vapor existed in the vapor grooves initially, which is caused by a higher pressure inside the wick due to evaporation in the evaporator core or vapor penetration into it. Temperature oscillation tends to occur in some of the startups at low head loads or some steady-state operations at high heat loads. Especially when the compensation chamber with the bayonet through is above the evaporator, the incidence rate of temperature oscillation is high.
