Necking defects have long troubled the application of cross-wedge rolling technology in aluminium alloy shaft parts.To accurately predict necking defects,new judgement conditions are established based on the thermal p...Necking defects have long troubled the application of cross-wedge rolling technology in aluminium alloy shaft parts.To accurately predict necking defects,new judgement conditions are established based on the thermal performance of 6082 aluminium alloy.The limit-sectional shrinkage without necking defects is achieved by combining theoretical calculation and finite-element model analysis,which couples heat transfer and deformation.In this paper,a 6082 aluminium alloy extruded rod with a 40 mm diameter rolled at a preheated temperature of 500℃and a rolling angular velocity of 1 rad/s is taken as an example.The simulation and experimental results show that necking defects do not occur on the rolled pieces if the sectional shrinkage is below the limit-sectional shrinkage but will occur when the sectional shrinkage is above it.The results prove that the prediction model of necking defects in cross-wedge rolling of 6082 aluminum alloy is feasible,and this research provides a theoretical basis for the qualified aluminum alloy shafts produced by the cross-wedge rolling.展开更多
This laboratory study examines the potential use of an anionic polyacrylamide(PAM)-based material as an environmentally sustainable additive for the stabilization of an expansive soil from South Australia.The experime...This laboratory study examines the potential use of an anionic polyacrylamide(PAM)-based material as an environmentally sustainable additive for the stabilization of an expansive soil from South Australia.The experimental program consisted of consistency limits,sediment volume,compaction and oedometer cyclic swell-shrink tests,performed using distilled water and four different PAM-to-water solutions of P_(D)=0.1 g/L,0.2 g/L,0.4 g/L and 0.6 g/L as the mixing liquids.Overall,the relative swelling and shrinkage strains were found to decrease with increasing number of applied swell-shrink cycles,with an‘elastic equilibrium’condition achieved on the conclusion of four cycles.The propensity for swelling/shrinkage potential reduction(for any given cycle)was found to be in favor of increasing the PAM dosage up to P_(D)=0.2 g/L,beyond which the excess PAM molecules self-associate as aggregates,thereby functioning as a lubricant instead of a flocculant;this critical dosage was termed‘maximum flocculation dosage’(MFD).The MFD assertion was discussed and validated using the consistency limits and sediment volume properties,both exhibiting only marginal variations beyond the identified MFD of P_(D)=0.2 g/L.The accumulated axial strain progressively transitioned from‘expansive’for the unamended soil to an ideal‘neutral’state at the MFD,while higher dosages demonstrated undesirable‘contractive’states.展开更多
基金Project(51975301)supported by the National Natural Science Foundation of ChinaProject(LZ17E050001)supported by the National Natural Science Foundation of Zhejiang Province of China。
文摘Necking defects have long troubled the application of cross-wedge rolling technology in aluminium alloy shaft parts.To accurately predict necking defects,new judgement conditions are established based on the thermal performance of 6082 aluminium alloy.The limit-sectional shrinkage without necking defects is achieved by combining theoretical calculation and finite-element model analysis,which couples heat transfer and deformation.In this paper,a 6082 aluminium alloy extruded rod with a 40 mm diameter rolled at a preheated temperature of 500℃and a rolling angular velocity of 1 rad/s is taken as an example.The simulation and experimental results show that necking defects do not occur on the rolled pieces if the sectional shrinkage is below the limit-sectional shrinkage but will occur when the sectional shrinkage is above it.The results prove that the prediction model of necking defects in cross-wedge rolling of 6082 aluminum alloy is feasible,and this research provides a theoretical basis for the qualified aluminum alloy shafts produced by the cross-wedge rolling.
基金funded by the Australian Research Council(ARC),Project No.DP140103004。
文摘This laboratory study examines the potential use of an anionic polyacrylamide(PAM)-based material as an environmentally sustainable additive for the stabilization of an expansive soil from South Australia.The experimental program consisted of consistency limits,sediment volume,compaction and oedometer cyclic swell-shrink tests,performed using distilled water and four different PAM-to-water solutions of P_(D)=0.1 g/L,0.2 g/L,0.4 g/L and 0.6 g/L as the mixing liquids.Overall,the relative swelling and shrinkage strains were found to decrease with increasing number of applied swell-shrink cycles,with an‘elastic equilibrium’condition achieved on the conclusion of four cycles.The propensity for swelling/shrinkage potential reduction(for any given cycle)was found to be in favor of increasing the PAM dosage up to P_(D)=0.2 g/L,beyond which the excess PAM molecules self-associate as aggregates,thereby functioning as a lubricant instead of a flocculant;this critical dosage was termed‘maximum flocculation dosage’(MFD).The MFD assertion was discussed and validated using the consistency limits and sediment volume properties,both exhibiting only marginal variations beyond the identified MFD of P_(D)=0.2 g/L.The accumulated axial strain progressively transitioned from‘expansive’for the unamended soil to an ideal‘neutral’state at the MFD,while higher dosages demonstrated undesirable‘contractive’states.
