目的针对装备向高温高速发展的需求,开展NiCr-Cr3C2、CoMoCr及NiCr Al Y涂层的高温摩擦磨损性能对比研究。方法针对上述三种涂层,通过超级爆炸喷涂工艺进行涂层制备,并测试涂层孔隙率、显微硬度、结合强度等基本性能,开展650℃/260 h的...目的针对装备向高温高速发展的需求,开展NiCr-Cr3C2、CoMoCr及NiCr Al Y涂层的高温摩擦磨损性能对比研究。方法针对上述三种涂层,通过超级爆炸喷涂工艺进行涂层制备,并测试涂层孔隙率、显微硬度、结合强度等基本性能,开展650℃/260 h的抗氧化试验和400、650℃的销盘式摩擦磨损试验,对比涂层的各项性能和在高温条件下的氧化质量增量、摩擦系数、磨损质量损失。结果抗氧化试验后,NiCr-Cr3C2、CoMoCrSi及NiCrAlY涂层氧化增重0.18、0.1、0.005 mg/(cm^2·h)。650℃时,摩擦系数分别为0.5、1.0、0.6。结论超级爆炸喷涂工艺制备的涂层组织、结合强度均优于等离子喷涂等常规喷涂工艺。高温下的氧化产物Co3O4与Cr2O3对高温摩擦系数有不同的影响。NiCr-75Cr3C2和NiCrAlY涂层在400、650℃可作为与SG37A材料的对磨副材料。展开更多
High temperature sliding wear behaviors of ion plating TiN composite coating with ion nitriding interlayer on 3Cr2W8V hot work die steel substrate during 500～700 ℃ were investigated. Phase structure was analyzed by ...High temperature sliding wear behaviors of ion plating TiN composite coating with ion nitriding interlayer on 3Cr2W8V hot work die steel substrate during 500～700 ℃ were investigated. Phase structure was analyzed by XRD and adhesion strength of TiN coating was measured by scratch test. The worn morphologies and wear mechanism of TiN composite coating were observed and analyzed by using SEM. The results showed that both adhesion strength and hardness of TiN composite coating with ion nitriding interlayer are higher than those of single TiN coating. Ion nitriding interlayer provides a stronger support for TiN coating. With increasing temperature, the wear rates and friction coefficient of all tested coatings increase. The wear resistance of TiN composite coating is better than that of single TiN coating. The wear mechanisms of TiN composite coating are mainly adhesion transfer wear and abrasive wear. The adhesion transfer wear becomes more severe as the test temperature increases. [展开更多
文摘目的针对装备向高温高速发展的需求,开展NiCr-Cr3C2、CoMoCr及NiCr Al Y涂层的高温摩擦磨损性能对比研究。方法针对上述三种涂层,通过超级爆炸喷涂工艺进行涂层制备,并测试涂层孔隙率、显微硬度、结合强度等基本性能,开展650℃/260 h的抗氧化试验和400、650℃的销盘式摩擦磨损试验,对比涂层的各项性能和在高温条件下的氧化质量增量、摩擦系数、磨损质量损失。结果抗氧化试验后,NiCr-Cr3C2、CoMoCrSi及NiCrAlY涂层氧化增重0.18、0.1、0.005 mg/(cm^2·h)。650℃时,摩擦系数分别为0.5、1.0、0.6。结论超级爆炸喷涂工艺制备的涂层组织、结合强度均优于等离子喷涂等常规喷涂工艺。高温下的氧化产物Co3O4与Cr2O3对高温摩擦系数有不同的影响。NiCr-75Cr3C2和NiCrAlY涂层在400、650℃可作为与SG37A材料的对磨副材料。
文摘High temperature sliding wear behaviors of ion plating TiN composite coating with ion nitriding interlayer on 3Cr2W8V hot work die steel substrate during 500～700 ℃ were investigated. Phase structure was analyzed by XRD and adhesion strength of TiN coating was measured by scratch test. The worn morphologies and wear mechanism of TiN composite coating were observed and analyzed by using SEM. The results showed that both adhesion strength and hardness of TiN composite coating with ion nitriding interlayer are higher than those of single TiN coating. Ion nitriding interlayer provides a stronger support for TiN coating. With increasing temperature, the wear rates and friction coefficient of all tested coatings increase. The wear resistance of TiN composite coating is better than that of single TiN coating. The wear mechanisms of TiN composite coating are mainly adhesion transfer wear and abrasive wear. The adhesion transfer wear becomes more severe as the test temperature increases. [
