An actively water-cooled limiter has been designed for the long pulse operation of an HT-7 device, by adopting an integrated structure-doped graphite and a copper alloy heat sink with a super carbon sheet serving as a...An actively water-cooled limiter has been designed for the long pulse operation of an HT-7 device, by adopting an integrated structure-doped graphite and a copper alloy heat sink with a super carbon sheet serving as a compliant layer between them. The behaviors of the integrated structure were evaluated in an electron beam facility under different heat loads and cooling conditions. The surface temperature and bulk temperature distribution were carefully measured by optical pyrometers and thermocouples under a steady state heat flux of 1 to 5 MW/m^2 and a water flow rate of 3 m^3/h, 4.5 m^3/h and 6 m^3/h, respectively. It was found that the surface temperature increased rapidly with the heat flux rising, but decreased only slightly with the water flow rate rising. The surface temperature reached approximately 1200℃ at 5 MW/m^2 of heat flux and 6 m^3/h of water flow. The primary experimental results indicate that the integrated design meets the requirements for the heat expelling capacity of the HT-7 device. A set of numerical simulations was also completed, whose outcome was in good accord with the experimental results.展开更多
The purpose of this paper was to investigate the impact of residual stresses on fatigue damage of offshore wind turbine monopiles by numerical analysis approach using ABAQUS software, a finite element analysis (FEA) t...The purpose of this paper was to investigate the impact of residual stresses on fatigue damage of offshore wind turbine monopiles by numerical analysis approach using ABAQUS software, a finite element analysis (FEA) tool. Three monopile models with the same dimension (within standard range) have been developed in ABAQUS and partitioned circumferentially into equal rings. Longitudinal partitions have been rotated through 180°as obtainable in practice. Characteristic loads typical of a real life offshore wind turbine environment have been applied to all three models, with tensile and compressive residual stresses applied as additional loads at the critical weld region to the first and second models while the third model had no additional load. With zero boundary conditions applied in all six degrees of freedom, the simulation has been run for 107 cycles of wind and wave loads as recommended in standards in each case. Stress results obtained from the critical weld region in the three models showed that the presence of tensile residual stresses equal to the material yield stress contributed a maximum 0.05% to fatigue damage of the monopile when compared with results from the model with no residual stress while the presence of compressive residual stresses with the magnitude of the yield stress of the material caused a gain of 0.06% in fatigue life by similar comparison, indicating negligible contribution of residual stresses to the stress build up in the critical weld region, thus suggesting that the magnitude of the residual stress as high as the yield stress of the material of the monopile is not large enough to cause the monopile to open up in the axial direction.展开更多
目前基于能量枢纽(energy hub,EH)的区域综合能源系统的优化运行缺乏对EH内热电联产(combined heat and power,CHP)机组热电比可调的考虑,且在此类场景中参与需求侧响应的负荷种类单一。针对此状况,构建双层优化模型,建立EH机组内部能...目前基于能量枢纽(energy hub,EH)的区域综合能源系统的优化运行缺乏对EH内热电联产(combined heat and power,CHP)机组热电比可调的考虑,且在此类场景中参与需求侧响应的负荷种类单一。针对此状况,构建双层优化模型,建立EH机组内部能效特性与外部能源分配的联系,实现内部机组高效运行和外部能源经济分配。模型通过卡罗需-库恩-塔克条件(Karush-Kuhn-Tucker Conditions,KKT)将双层优化转换为单层优化,并用确定性优化软件求解。算例结果表明,EH双层优化运行模型可减少用能成本,提高用能效率。通过调节CHP热电比,同时利用广义弹性负荷参与响应,可以减小CHP热电比与区域内热电负荷比之间差距,从而提高CHP供能比例,实现区域综合能源系统高效经济运行。展开更多
基金The project partially supported by National Natural Science Foundation of China (No. 10275069)
文摘An actively water-cooled limiter has been designed for the long pulse operation of an HT-7 device, by adopting an integrated structure-doped graphite and a copper alloy heat sink with a super carbon sheet serving as a compliant layer between them. The behaviors of the integrated structure were evaluated in an electron beam facility under different heat loads and cooling conditions. The surface temperature and bulk temperature distribution were carefully measured by optical pyrometers and thermocouples under a steady state heat flux of 1 to 5 MW/m^2 and a water flow rate of 3 m^3/h, 4.5 m^3/h and 6 m^3/h, respectively. It was found that the surface temperature increased rapidly with the heat flux rising, but decreased only slightly with the water flow rate rising. The surface temperature reached approximately 1200℃ at 5 MW/m^2 of heat flux and 6 m^3/h of water flow. The primary experimental results indicate that the integrated design meets the requirements for the heat expelling capacity of the HT-7 device. A set of numerical simulations was also completed, whose outcome was in good accord with the experimental results.
文摘The purpose of this paper was to investigate the impact of residual stresses on fatigue damage of offshore wind turbine monopiles by numerical analysis approach using ABAQUS software, a finite element analysis (FEA) tool. Three monopile models with the same dimension (within standard range) have been developed in ABAQUS and partitioned circumferentially into equal rings. Longitudinal partitions have been rotated through 180°as obtainable in practice. Characteristic loads typical of a real life offshore wind turbine environment have been applied to all three models, with tensile and compressive residual stresses applied as additional loads at the critical weld region to the first and second models while the third model had no additional load. With zero boundary conditions applied in all six degrees of freedom, the simulation has been run for 107 cycles of wind and wave loads as recommended in standards in each case. Stress results obtained from the critical weld region in the three models showed that the presence of tensile residual stresses equal to the material yield stress contributed a maximum 0.05% to fatigue damage of the monopile when compared with results from the model with no residual stress while the presence of compressive residual stresses with the magnitude of the yield stress of the material caused a gain of 0.06% in fatigue life by similar comparison, indicating negligible contribution of residual stresses to the stress build up in the critical weld region, thus suggesting that the magnitude of the residual stress as high as the yield stress of the material of the monopile is not large enough to cause the monopile to open up in the axial direction.
