Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The in...Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The influence of cutting conditions on tool wear has been focused on the turning process, and their influence on tool wear in milling process as well as the influence of tool wear on cutting force coefficients has not been investigated comprehensively. To fully understand the tool wear behavior in milling process with inserts, the influence of cutting parameters on tool wear in the milling of titanium alloys Ti6A14V by using indexable cutters is investigated. The tool wear rate and trends under different feed per tooth, cutting speed, axial depth of cut and radial depth of cut are analyzed. The results show that the feed rate per tooth and the radial depth of cut have a large influence on tool wear in milling Ti6A14V with coated insert. To reduce tool wear, cutting parameters for coated inserts under experimental cutting conditions are set as： feed rate per tooth less than 0.07 mm, radial depth of cut less than 1.0 mm, and cutting speed sets between 60 and 150 m/min. Investigation on the relationship between tool wear and cutting force coefficients shows that tangential edge constant increases with tool wear and cutter edge chipping can lead to a great variety of tangential cutting force coefficient. The proposed research provides the basic data for evaluating the machinability of milling Ti6A14V alloy with coated inserts, and the recommend cutting parameters can be immediately applied in practical production.展开更多
This paper presents the characteristics of nickel-based alloys, alongside their division into groups, and describes thefeatures that make such materials difficult to grind. The possibilities of exerting a positive inf...This paper presents the characteristics of nickel-based alloys, alongside their division into groups, and describes thefeatures that make such materials difficult to grind. The possibilities of exerting a positive influence upon machining conditions,especially through the proper application of grinding fluids, are briefly presented. Both the precise methodologies for, and theresults of, the experimental tests carried out on flat surfaces are also detailed. The aim of these tests was to determine the influenceof the application of two types of grinding liquid （Ecocut Mikro Plus 82 and Biocut 3000） upon the grinding force values andsurface roughness of the machined workpieces made from three nickel alloys （Nickel 201, INCONEL~ alloy 600, and MONEL^alloy 400）. An additional goal of the tests was to determine the influence of grinding wheel structure on the course and results ofthe machining process. The results indicate that the physical and chemical properties of Biocut 3000 enabled the most advanta-geous properties of the machined surface roughness, alongside a simultaneous increase in grinding power, when compared to theresults when applying Ecocut Mikro Plus 82. The results showed an almost inversely proportional dependence upon the specifictangential grinding force Ft＇ and arithmetic mean deviation of the surface profile Ra values, especially in cases of machining Nickel201 and INCONEL alloy 600. The original traverse grinding methodology used in the tests made it possible to assess the changesof the grinding conditions within the conventionally selected zones.展开更多
基金Supported by National Basic Research Program of China(973 Program,Grant No.2013CB035802)National Natural Science Foundation of China(Grant No.51575453)+1 种基金Fundamental Research Funds for the Central Universities(Grant No.3102015JCS05002)the 111 Project,China(Grant No.B13044)
文摘Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The influence of cutting conditions on tool wear has been focused on the turning process, and their influence on tool wear in milling process as well as the influence of tool wear on cutting force coefficients has not been investigated comprehensively. To fully understand the tool wear behavior in milling process with inserts, the influence of cutting parameters on tool wear in the milling of titanium alloys Ti6A14V by using indexable cutters is investigated. The tool wear rate and trends under different feed per tooth, cutting speed, axial depth of cut and radial depth of cut are analyzed. The results show that the feed rate per tooth and the radial depth of cut have a large influence on tool wear in milling Ti6A14V with coated insert. To reduce tool wear, cutting parameters for coated inserts under experimental cutting conditions are set as： feed rate per tooth less than 0.07 mm, radial depth of cut less than 1.0 mm, and cutting speed sets between 60 and 150 m/min. Investigation on the relationship between tool wear and cutting force coefficients shows that tangential edge constant increases with tool wear and cutter edge chipping can lead to a great variety of tangential cutting force coefficient. The proposed research provides the basic data for evaluating the machinability of milling Ti6A14V alloy with coated inserts, and the recommend cutting parameters can be immediately applied in practical production.
文摘This paper presents the characteristics of nickel-based alloys, alongside their division into groups, and describes thefeatures that make such materials difficult to grind. The possibilities of exerting a positive influence upon machining conditions,especially through the proper application of grinding fluids, are briefly presented. Both the precise methodologies for, and theresults of, the experimental tests carried out on flat surfaces are also detailed. The aim of these tests was to determine the influenceof the application of two types of grinding liquid （Ecocut Mikro Plus 82 and Biocut 3000） upon the grinding force values andsurface roughness of the machined workpieces made from three nickel alloys （Nickel 201, INCONEL~ alloy 600, and MONEL^alloy 400）. An additional goal of the tests was to determine the influence of grinding wheel structure on the course and results ofthe machining process. The results indicate that the physical and chemical properties of Biocut 3000 enabled the most advanta-geous properties of the machined surface roughness, alongside a simultaneous increase in grinding power, when compared to theresults when applying Ecocut Mikro Plus 82. The results showed an almost inversely proportional dependence upon the specifictangential grinding force Ft＇ and arithmetic mean deviation of the surface profile Ra values, especially in cases of machining Nickel201 and INCONEL alloy 600. The original traverse grinding methodology used in the tests made it possible to assess the changesof the grinding conditions within the conventionally selected zones.
