Gigacycle fatigue behavior of 60Si2CrVA high strength spring steel was investigated by ultrasonic fatigue test machine. Fatigue fractography was observed by scanning electron microscopy （SEM）. Maximum inclusion size...Gigacycle fatigue behavior of 60Si2CrVA high strength spring steel was investigated by ultrasonic fatigue test machine. Fatigue fractography was observed by scanning electron microscopy （SEM）. Maximum inclusion sizes and fatigue strength in different volumes were estimated by statistics of extreme values （SEV） and generalized Pareto distribution （GPD） methods. The results showed that S N curves of 60Si2CrVA spring steels for two rolling processes were not horizontal asymptotes but a gradient in a regime of 109 cycles, and traditional fatigue limits were eliminated. Surface machined topography and inclusions in steel were major factors that led to elimination of fatigue limit for 60Si2CrVA spring steel. The SEV and GPD methods could effectively predict size of the maximum inclusion and fatigue strength in different volumes of 60Si2CrVA spring steel. Predicted fatigue strength was in accordance with experimental results by ultrasonic fatigue testing.展开更多
The fatigue behavior of a high strength steel 300 M in the gigacycle regime was investigated. Fully reversed tension - compression fatigue tests at ambient temperature were performed using an ultrasonic fatigue system...The fatigue behavior of a high strength steel 300 M in the gigacycle regime was investigated. Fully reversed tension - compression fatigue tests at ambient temperature were performed using an ultrasonic fatigue system operating at 20 kHz.The staircase test method was employed to obtain accurate values of the mean fatigue strength corresponding to fixed numbers of cycles up to 10~9.These results were compared to the curve which is estimated by the data tested in the mid-long life regime on conventional servo hydraulic test machine at 20 Hz.Results indicate that the fatigue strength determined from ultrasonic fatigue testing is lightly higher than conventional testing in the range of 10~6-10~7 cycles.It is obvious that nucleations of fractures tend to occur below the surface, if fractures happen after more than 10~7 cycles.All the fractured specimens fails from internal SiO_2 inclusions or smaller carbides and carbide clusters.展开更多
Gigacycle fatigue behaviors of two SNCM439 steels with different tensile strengthes were experimentally studied by rotating bending tests,to investigate the effects of the tensile strength obtained by different heat t...Gigacycle fatigue behaviors of two SNCM439 steels with different tensile strengthes were experimentally studied by rotating bending tests,to investigate the effects of the tensile strength obtained by different heat treatment processes on very high cycle fatigue failure mechanisms.The material with higher tensile strength of 1 710 MPa exhibited typical gigacycle fatigue failure characteristics,whereas one with lower tensile strength of 1 010 MPa showed only traditional fatigue limit during the tests and no gigacycle failure could be found even when the specimen ran up to more than 10 8 cycles.Metallographic and fractographic analysis were carried out by an optical microscope （OM） and scanning electron microscope （SEM）.It showed two different crack initiation mechanisms that for the specimen with lower tensile strength the crack prefers surface initiation and for that with higher strength the crack initiates from subsurface inclusions revealed by a fish-eye like microstructure.展开更多
基金Sponsored by National Basic Research Program(973 Program)of China(2004CB619100)
文摘Gigacycle fatigue behavior of 60Si2CrVA high strength spring steel was investigated by ultrasonic fatigue test machine. Fatigue fractography was observed by scanning electron microscopy （SEM）. Maximum inclusion sizes and fatigue strength in different volumes were estimated by statistics of extreme values （SEV） and generalized Pareto distribution （GPD） methods. The results showed that S N curves of 60Si2CrVA spring steels for two rolling processes were not horizontal asymptotes but a gradient in a regime of 109 cycles, and traditional fatigue limits were eliminated. Surface machined topography and inclusions in steel were major factors that led to elimination of fatigue limit for 60Si2CrVA spring steel. The SEV and GPD methods could effectively predict size of the maximum inclusion and fatigue strength in different volumes of 60Si2CrVA spring steel. Predicted fatigue strength was in accordance with experimental results by ultrasonic fatigue testing.
基金supported by the National Natural Science Foundation of China(50775182)the Scientific Research Foundation for the Returned Overseas Chinese Scholars, State Education Ministry
文摘The fatigue behavior of a high strength steel 300 M in the gigacycle regime was investigated. Fully reversed tension - compression fatigue tests at ambient temperature were performed using an ultrasonic fatigue system operating at 20 kHz.The staircase test method was employed to obtain accurate values of the mean fatigue strength corresponding to fixed numbers of cycles up to 10~9.These results were compared to the curve which is estimated by the data tested in the mid-long life regime on conventional servo hydraulic test machine at 20 Hz.Results indicate that the fatigue strength determined from ultrasonic fatigue testing is lightly higher than conventional testing in the range of 10~6-10~7 cycles.It is obvious that nucleations of fractures tend to occur below the surface, if fractures happen after more than 10~7 cycles.All the fractured specimens fails from internal SiO_2 inclusions or smaller carbides and carbide clusters.
基金supported by funds of MHI Corporation,the National Natural Science Foundation of China (10872105)
文摘Gigacycle fatigue behaviors of two SNCM439 steels with different tensile strengthes were experimentally studied by rotating bending tests,to investigate the effects of the tensile strength obtained by different heat treatment processes on very high cycle fatigue failure mechanisms.The material with higher tensile strength of 1 710 MPa exhibited typical gigacycle fatigue failure characteristics,whereas one with lower tensile strength of 1 010 MPa showed only traditional fatigue limit during the tests and no gigacycle failure could be found even when the specimen ran up to more than 10 8 cycles.Metallographic and fractographic analysis were carried out by an optical microscope （OM） and scanning electron microscope （SEM）.It showed two different crack initiation mechanisms that for the specimen with lower tensile strength the crack prefers surface initiation and for that with higher strength the crack initiates from subsurface inclusions revealed by a fish-eye like microstructure.
