H13 tool steel was successfully prepared by selective laser melting(SLM)technology.The effects of heat treatment on the microstructure,mechanical properties,and tribological properties of SLMed H13 steel were investig...H13 tool steel was successfully prepared by selective laser melting(SLM)technology.The effects of heat treatment on the microstructure,mechanical properties,and tribological properties of SLMed H13 steel were investigated.The heat treatment process involved a solution treatment and a double aging treatment of the deposited H13 tool steel prepared by SLM.The aim is to optimize the microstructure and mechanical properties of SLMed H13 steel.Due to the rapid heating and cooling effects of SLM,carbide precipitation in the deposited H13 steel was not uniform and residual stresses were present.The purpose of the solution treatment is to dissolve the solution at a high temperature to eliminate the residual stresses and defects introduced by the SLM-forming structure.The solution treatment and first aging treatment produced the precipitation of small carbides at the grain boundaries and inside the crystals,which increased the hardness of SLMed H13 steel.The hardness increased from 538±4.0 HV of the as-deposited sample to 548±5.8 HV of samples after the first aging treatment.Accordingly,the ultimate tensile strength and the elongation at break decreased from 1882 MPa and 11.5%in the as-deposited sample to 1697 MPa and 7.9%in those after the first aging treatment,respectively.Furthermore,the friction coefficient and wear rate in the as-deposited sample decreased from 0.5160 and 2.36×10^(–6)mm^(−3)N^(−1)m^(−1)to 0.4244 and 1.04×10^(–6)mm^(−3)N^(−1)m^(−1),respectively.However,the distribution of carbides inside the crystals was not uniform.The second aging treatment adjusted the morphology of carbide precipitation and made it more uniform,but the precipitation of carbides grew and settled at the bottom of the grain boundaries.The hardness decreased to 533±6.7 HV compared with that with the first aging treatment,but the ultimate tensile strength and plasticity reached a balance(1807 MPa,14.05%).Accordingly,the friction coefficient and wear rate also showed a stable and decreasing trend(0.4407,0.98×10^(�展开更多
Microstructure and mechanical properties of a new high-strength Mg–6 Zn–4 Al–1 Sn alloy were investigated. Microstructure of the as-cast Mg alloy exhibited partially divorced characteristics. The dendritic structur...Microstructure and mechanical properties of a new high-strength Mg–6 Zn–4 Al–1 Sn alloy were investigated. Microstructure of the as-cast Mg alloy exhibited partially divorced characteristics. The dendritic structure of the Mg–6 Zn–4 Al alloy was significantly refined with the addition of 1%（in weight） Sn, but Mg2 Sn phases were not formed. In addition, an icosahedral quasi-crystal phase was formed in the as-cast Mg–6 Zn–4 Al–1 Sn alloy. It was found that after the double-aging treatment through two different heat treatments on the Mg–6 Zn–4 Al–1 Sn alloy, the precipitates were finer and far more densely dispersed in the matrix compared with single-aged counterpart, resulting in a significant improvement in tensile strength with yield strength, ultimate tensile strength and elongation of 175 MPa, 335 MPa and 11%,respectively.展开更多
To improve the ductility of a commercial Mg−rare earth alloy EV31A(Mg−3Nd−1.5Gd−0.3Zn−0.5Zr),a heat treatment method called double aging is explored,and its effect on mechanical properties and microstructure of the al...To improve the ductility of a commercial Mg−rare earth alloy EV31A(Mg−3Nd−1.5Gd−0.3Zn−0.5Zr),a heat treatment method called double aging is explored,and its effect on mechanical properties and microstructure of the alloy is studied.Ultimate strength and elongation of the alloy can be increased to 288 MPa and 6.6%by the optimum double aging process,compared to 273 MPa and 4.9%after single aging.Time consumption of the aging process is also significantly decreased from 16 h(single aging)to 2 h.HAADF-STEM characterization shows that the primary precipitate isβ'phase,which is similar toβ'phase in Mg−Nd binary alloy.By double aging,theβ'phase is finer and more densely distributed compared with single aging,with approximately double density and half size,which explains the improvement in strength and ductility.展开更多
基金supported by National Natural Science Foundation of China(Grant No.52104341)Key Technologies Research and Development Program(Grant Nos.2021YFB3701902 and 2021YFB3701903)+1 种基金Natural Science Basic Research Program of Shaanxi Province(Grant Nos.2022JM-259 and 2022JQ-367)Postdoctoral Research Foundation of China(Grant No.2021M702554).
文摘H13 tool steel was successfully prepared by selective laser melting(SLM)technology.The effects of heat treatment on the microstructure,mechanical properties,and tribological properties of SLMed H13 steel were investigated.The heat treatment process involved a solution treatment and a double aging treatment of the deposited H13 tool steel prepared by SLM.The aim is to optimize the microstructure and mechanical properties of SLMed H13 steel.Due to the rapid heating and cooling effects of SLM,carbide precipitation in the deposited H13 steel was not uniform and residual stresses were present.The purpose of the solution treatment is to dissolve the solution at a high temperature to eliminate the residual stresses and defects introduced by the SLM-forming structure.The solution treatment and first aging treatment produced the precipitation of small carbides at the grain boundaries and inside the crystals,which increased the hardness of SLMed H13 steel.The hardness increased from 538±4.0 HV of the as-deposited sample to 548±5.8 HV of samples after the first aging treatment.Accordingly,the ultimate tensile strength and the elongation at break decreased from 1882 MPa and 11.5%in the as-deposited sample to 1697 MPa and 7.9%in those after the first aging treatment,respectively.Furthermore,the friction coefficient and wear rate in the as-deposited sample decreased from 0.5160 and 2.36×10^(–6)mm^(−3)N^(−1)m^(−1)to 0.4244 and 1.04×10^(–6)mm^(−3)N^(−1)m^(−1),respectively.However,the distribution of carbides inside the crystals was not uniform.The second aging treatment adjusted the morphology of carbide precipitation and made it more uniform,but the precipitation of carbides grew and settled at the bottom of the grain boundaries.The hardness decreased to 533±6.7 HV compared with that with the first aging treatment,but the ultimate tensile strength and plasticity reached a balance(1807 MPa,14.05%).Accordingly,the friction coefficient and wear rate also showed a stable and decreasing trend(0.4407,0.98×10^(�
基金supported by the National Basic Research Program of China (No. 2013CB632205)the National Key Research and Development Program of China (No. 2016YFB301105)
文摘Microstructure and mechanical properties of a new high-strength Mg–6 Zn–4 Al–1 Sn alloy were investigated. Microstructure of the as-cast Mg alloy exhibited partially divorced characteristics. The dendritic structure of the Mg–6 Zn–4 Al alloy was significantly refined with the addition of 1%（in weight） Sn, but Mg2 Sn phases were not formed. In addition, an icosahedral quasi-crystal phase was formed in the as-cast Mg–6 Zn–4 Al–1 Sn alloy. It was found that after the double-aging treatment through two different heat treatments on the Mg–6 Zn–4 Al–1 Sn alloy, the precipitates were finer and far more densely dispersed in the matrix compared with single-aged counterpart, resulting in a significant improvement in tensile strength with yield strength, ultimate tensile strength and elongation of 175 MPa, 335 MPa and 11%,respectively.
基金This work was supported by the National Natural Science Foundation of China(No.51825101).
文摘To improve the ductility of a commercial Mg−rare earth alloy EV31A(Mg−3Nd−1.5Gd−0.3Zn−0.5Zr),a heat treatment method called double aging is explored,and its effect on mechanical properties and microstructure of the alloy is studied.Ultimate strength and elongation of the alloy can be increased to 288 MPa and 6.6%by the optimum double aging process,compared to 273 MPa and 4.9%after single aging.Time consumption of the aging process is also significantly decreased from 16 h(single aging)to 2 h.HAADF-STEM characterization shows that the primary precipitate isβ'phase,which is similar toβ'phase in Mg−Nd binary alloy.By double aging,theβ'phase is finer and more densely distributed compared with single aging,with approximately double density and half size,which explains the improvement in strength and ductility.
