An optical phase locking method based on direct phase control is proposed.The core of this method is to synchronize the carrier by directly changing the phase of the local beam.The corresponding experimental device an...An optical phase locking method based on direct phase control is proposed.The core of this method is to synchronize the carrier by directly changing the phase of the local beam.The corresponding experimental device and the supporting algorithm were configured to verify the feasibility of this method.Phase locking can be completed without cycle skipping,and the acquisition time is 530 ns.Without an optical preamplifier,a sensitivity of-34.4 d Bm is obtained,and the bit error rate is 10^(-9) for 2.5 Gbit/s binary phase-shift keying modulation.The measured standard deviation of the phase error is 5.2805°.展开更多
Due to the large number of submodules(SMs),and modular multilevel converters(MMCs)in high-voltage applications,they are usually regulated by the nearest level modulation(NLM).Moreover,the large number of SMs causes a ...Due to the large number of submodules(SMs),and modular multilevel converters(MMCs)in high-voltage applications,they are usually regulated by the nearest level modulation(NLM).Moreover,the large number of SMs causes a challenge for the fault diagnosis strategy(FDS).This paper proposes a currentless FDS for MMC with NLM.In FDS,the voltage sensor is relocated to measure the output voltage of the SM.To acquire the capacitor voltage and avoid increasing extra sensors,a capacitor voltage calculation method is proposed.Based on the measurement of output voltages,the faults can be detected and the number of different-type switch open-circuit faults can be confirmed from the numerous SMs in an arm,which narrows the scope of fault localization.Then,the faulty SMs and faulty switches in these SMs are further located without arm current according to the sorting of capacitor voltages in the voltage balancing algorithm.The FDS is independent of the arm current,which can reduce the communication cost in the hierarchical control system of MMC.Furthermore,the proposed FDS not only simplifies the identification of switch open-circuit faults by confirming the scope of faults,but also detects and locates multiple different-type faults in an arm.The effectiveness of the proposed strategy is verified by the simulation results.展开更多
基金supported by the National Key R&D Program of China(No.2020YFB0408302)Strategic Priority Research Program of Chinese Academy of Sciences(No.XDB43030400)+1 种基金National Natural Science Foundation of China(No.91938302)Key Project of Chinese Academy of Sciences(No.ZDRWKT-2019-1-01-0302)。
文摘An optical phase locking method based on direct phase control is proposed.The core of this method is to synchronize the carrier by directly changing the phase of the local beam.The corresponding experimental device and the supporting algorithm were configured to verify the feasibility of this method.Phase locking can be completed without cycle skipping,and the acquisition time is 530 ns.Without an optical preamplifier,a sensitivity of-34.4 d Bm is obtained,and the bit error rate is 10^(-9) for 2.5 Gbit/s binary phase-shift keying modulation.The measured standard deviation of the phase error is 5.2805°.
基金supported by the State Key Laboratory of Advanced Power Transmission Technology(GEIRI-SKL-2020-011)。
文摘Due to the large number of submodules(SMs),and modular multilevel converters(MMCs)in high-voltage applications,they are usually regulated by the nearest level modulation(NLM).Moreover,the large number of SMs causes a challenge for the fault diagnosis strategy(FDS).This paper proposes a currentless FDS for MMC with NLM.In FDS,the voltage sensor is relocated to measure the output voltage of the SM.To acquire the capacitor voltage and avoid increasing extra sensors,a capacitor voltage calculation method is proposed.Based on the measurement of output voltages,the faults can be detected and the number of different-type switch open-circuit faults can be confirmed from the numerous SMs in an arm,which narrows the scope of fault localization.Then,the faulty SMs and faulty switches in these SMs are further located without arm current according to the sorting of capacitor voltages in the voltage balancing algorithm.The FDS is independent of the arm current,which can reduce the communication cost in the hierarchical control system of MMC.Furthermore,the proposed FDS not only simplifies the identification of switch open-circuit faults by confirming the scope of faults,but also detects and locates multiple different-type faults in an arm.The effectiveness of the proposed strategy is verified by the simulation results.
