Compound section is referred to a section the surface of which is made of several sub-sections with different flow characteristics. The difference in the hydraulic and geometry characteristics causes a complexity in f...Compound section is referred to a section the surface of which is made of several sub-sections with different flow characteristics. The difference in the hydraulic and geometry characteristics causes a complexity in flow hydraulic and creates an interaction between the main channel and floodplains, resulting in an apparent shear stress and a transverse momentum transfer. The amount of such a stress plays an important role in many river engineering measures [1]. Due to the flow complexity, the common approximate analytical methods are not enough to identify the flow profile. The FLOW3D Software with its great features in three-dimensional analysis of flow field is used as a tool to investigate the shear stress in a direct symmetrical compound rectangular channel. After the simulation of models, it is found that an increase in the relative width and relative depth parameters decreases the percentage of apparent shear stress and an increase in the relative roughness causes it to be increased [2].展开更多
Plasma radical nitriding was performed to harden the surface of SCM440 steel for 1-10 h at temperature range of 450-550℃. This process involved the use of NH3 gas instead of N2 gas employed for the well-established p...Plasma radical nitriding was performed to harden the surface of SCM440 steel for 1-10 h at temperature range of 450-550℃. This process involved the use of NH3 gas instead of N2 gas employed for the well-established plasma nitriding method. No compound layer was formed during this process except the experiment carried out at 500℃ for 10 h. The main phase produced in the diffusion zone was identified to be γ＇-Fe4（N, C）. A diffusion depth increased with increasing treatment temperature and time （up to about 250 μm）. The surface hardness of radical nitrided layer was about two times higher than that of the untreated surface. The tensile test was carried out to estimate the mechanical properties of surface-hardened SCM440 steel prepared at various plasma radical nitriding treatment time and temperature. The influence of radical nitriding treatment on the tensile strength of the specimen was found to be insignificant. The highest value of the ultimate tensile strength was obtained in the experiment carried out at 500℃ for 1 h. However, the elongation was greatly affected by the radical nitriding processing parameters. The maximum value of elongation, which is equal to about 18.1%, was also obtained under the condition of 500℃ for 1 h.展开更多
Compound open channel flows appear in most natural rivers are of great importance in river management and flood control.In this study,large eddy simulations were carried out to simulate the compound open channel flows...Compound open channel flows appear in most natural rivers are of great importance in river management and flood control.In this study,large eddy simulations were carried out to simulate the compound open channel flows with four different depth ratios(hr=0.10,0.25,0.50,and 0.75).The main flow velocity,secondary flow,Reynolds stress,and bed shear stress were obtained from numerical simulations.The depth-averaged stream wise momentum equation was used to quantify the lateral momentum exchange between the main channel and floodplain.The instantaneous coherent structures were presented by the Q criterion method.The impact of hr on flow structure and turbulence charac-teristics was analyzed.The results showed that with the increase of hr,the high velocity area in the main channel shifted to the floodplain,and the dip phenomenon became more obvious;the Reynolds stress largely contributed to the lateral momentum exchange within the flows near the side walls of floodplain;and the vortex structures were found to significantly increase in the floodplain region.展开更多
The theory of an eddy viscosity model is applied to the study of the flow in a compound channel which is partially vegetated. The governing equation is constituted by analyzing the longitudinal forces acting on the un...The theory of an eddy viscosity model is applied to the study of the flow in a compound channel which is partially vegetated. The governing equation is constituted by analyzing the longitudinal forces acting on the unit volume where the effect of the vegetation on the flow is considered as a drag force item, The compound channel is divided into 3 sub-regions in the transverse direction, and the coefficients in every region＇s differential equations were solved simultaneously. Thus, the analytical solution of the transverse distribution of the depth-averaged velocity for uniform flow in a partially vegetated compound channel was obtained. The results can be used to predict the transverse distribution of bed shear stress, which has an important effect on the transportation of sediment. By comparing the analytical results with the measured data, the analytical solution in this paper is shown to be sufficiently accurate to predict most hydraulic features for engineering design purposes.展开更多
文摘Compound section is referred to a section the surface of which is made of several sub-sections with different flow characteristics. The difference in the hydraulic and geometry characteristics causes a complexity in flow hydraulic and creates an interaction between the main channel and floodplains, resulting in an apparent shear stress and a transverse momentum transfer. The amount of such a stress plays an important role in many river engineering measures [1]. Due to the flow complexity, the common approximate analytical methods are not enough to identify the flow profile. The FLOW3D Software with its great features in three-dimensional analysis of flow field is used as a tool to investigate the shear stress in a direct symmetrical compound rectangular channel. After the simulation of models, it is found that an increase in the relative width and relative depth parameters decreases the percentage of apparent shear stress and an increase in the relative roughness causes it to be increased [2].
文摘Plasma radical nitriding was performed to harden the surface of SCM440 steel for 1-10 h at temperature range of 450-550℃. This process involved the use of NH3 gas instead of N2 gas employed for the well-established plasma nitriding method. No compound layer was formed during this process except the experiment carried out at 500℃ for 10 h. The main phase produced in the diffusion zone was identified to be γ＇-Fe4（N, C）. A diffusion depth increased with increasing treatment temperature and time （up to about 250 μm）. The surface hardness of radical nitrided layer was about two times higher than that of the untreated surface. The tensile test was carried out to estimate the mechanical properties of surface-hardened SCM440 steel prepared at various plasma radical nitriding treatment time and temperature. The influence of radical nitriding treatment on the tensile strength of the specimen was found to be insignificant. The highest value of the ultimate tensile strength was obtained in the experiment carried out at 500℃ for 1 h. However, the elongation was greatly affected by the radical nitriding processing parameters. The maximum value of elongation, which is equal to about 18.1%, was also obtained under the condition of 500℃ for 1 h.
基金supported by the Fundamental Research Funds for the Central Universities(Grants No.B200202116 and B200204044)the National Natural Science Foundation of China(Grant No.51879086)the 111 Project from the Minstry of Education and State Administration of Foreign Expert Affairs of China(Grant No.B17015).
文摘Compound open channel flows appear in most natural rivers are of great importance in river management and flood control.In this study,large eddy simulations were carried out to simulate the compound open channel flows with four different depth ratios(hr=0.10,0.25,0.50,and 0.75).The main flow velocity,secondary flow,Reynolds stress,and bed shear stress were obtained from numerical simulations.The depth-averaged stream wise momentum equation was used to quantify the lateral momentum exchange between the main channel and floodplain.The instantaneous coherent structures were presented by the Q criterion method.The impact of hr on flow structure and turbulence charac-teristics was analyzed.The results showed that with the increase of hr,the high velocity area in the main channel shifted to the floodplain,and the dip phenomenon became more obvious;the Reynolds stress largely contributed to the lateral momentum exchange within the flows near the side walls of floodplain;and the vortex structures were found to significantly increase in the floodplain region.
基金the National Natural Science Foundation of China(Nos.50679061,50709025and50749031)
文摘The theory of an eddy viscosity model is applied to the study of the flow in a compound channel which is partially vegetated. The governing equation is constituted by analyzing the longitudinal forces acting on the unit volume where the effect of the vegetation on the flow is considered as a drag force item, The compound channel is divided into 3 sub-regions in the transverse direction, and the coefficients in every region＇s differential equations were solved simultaneously. Thus, the analytical solution of the transverse distribution of the depth-averaged velocity for uniform flow in a partially vegetated compound channel was obtained. The results can be used to predict the transverse distribution of bed shear stress, which has an important effect on the transportation of sediment. By comparing the analytical results with the measured data, the analytical solution in this paper is shown to be sufficiently accurate to predict most hydraulic features for engineering design purposes.
