The carrier frequency offset（CFO）and impulse noise always affect the performance of underwater acoustic communication_systems.The CFO and impulse noise could be estimated by using the null subcarriers to cancel the ...The carrier frequency offset（CFO）and impulse noise always affect the performance of underwater acoustic communication_systems.The CFO and impulse noise could be estimated by using the null subcarriers to cancel the effects of the two types of interference.The null subcarriers estimation methods include optimal separate estimation and joint estimation.The separate estimation firstly estimates the CFO value and then estimates the impulse noise value.However,the CFO and impulse noise always affect each other when either of them is estimated separately.The performance could be improved by using the joint estimation.The results of simulations and experiments have showed that these two optimization methods have good performance and the joint estimation has better performance than the separate estimation method.There is 3 dB performance gain at the BER value of 10^（-2）when using the joint estimation method.Thus these methods could improve the system robustness by using the CFO compensation and impulse noise suppression.展开更多
Spectral efficiency and energy efficiency are two important performance indicators of satellite systems. The Quasi-Constant Envelope Orthogonal Frequency Division Multiplexing(QCE-OFDM) technique can achieve both high...Spectral efficiency and energy efficiency are two important performance indicators of satellite systems. The Quasi-Constant Envelope Orthogonal Frequency Division Multiplexing(QCE-OFDM) technique can achieve both high spectral efficiency and low peak-to-average power ratio(PAPR). Therefore, the QCE-OFDM technique is considered as a promising candidate multi-carrier technique for satellite systems. However, the Doppler effect will cause the carrier frequency offset(CFO), and the non-ideal oscillator will cause the carrier phase offset(CPO) in satellite systems. The CFO and CPO will further result in the bit-error-rate(BER) performance degradation. Hence, it is important to estimate and compensate the CFO and CPO. This paper analyzes the effects of both CFO and CPO in QCE-OFDM satellite systems. Furthermore, we propose a joint CFO and CPO estimation method based on the pilot symbols in the frequency domain. In addition, the optimal pilot symbol structure with different pilot overheads is designed according to the minimum Cramer-Rao bound(CRB) criterion. Simulation results show that the estimation accuracy of the proposed method is close to the CRB.展开更多
This paper presents the architectures, algorithms, and implementation considerations of the digital phase locked loop (DPLL) used for burst-mode packet DS-CDMA receivers. As we know, carrier offset is a rather challen...This paper presents the architectures, algorithms, and implementation considerations of the digital phase locked loop (DPLL) used for burst-mode packet DS-CDMA receivers. As we know, carrier offset is a rather challenging problem in CDMA system. According to different applications, different DPLL forms should be adopted to correct different maximum carrier offset in CDMA systems. One classical DPLL and two novel DPLL forms are discussed in the paper. The acquisition range of carrier offset can be widened by using the two novel DPLL forms without any performance degradation such as longer acquisition time or larger variance of the phase error. The maximum acquisition range is 1/(4T), where T is the symbol period. The design can be implemented by FPGA directly.展开更多
In this paper,we review our joint timing and frequency synchronization algorithms in coherent optical orthogonal frequency division multiplexing(CO-OFDM)systems.We first present a timing estimation method by designing...In this paper,we review our joint timing and frequency synchronization algorithms in coherent optical orthogonal frequency division multiplexing(CO-OFDM)systems.We first present a timing estimation method by designing the pattern of the training symbol,whose timing metric has a sharp and clear peak,to ensure accurate timing offset(TO)estimation performance.Then we provide both data-aided(DA)and blind(BL)approaches to estimate the carrier frequency offset(CFO).For the DA algorithm,we utilize the same training symbol structure as the timing estimation does,while for the BL algorithm,we utilize the zero-subcarrier power(ZSP)to achieve full-range CFO estimation.Note that our joint timing and frequency synchronization approaches require only one OFDM symbol,which ensure not only the data transmission efficiency,but also the TO and CFO estimation performance.A modified BL ZSP algorithm is proposed to further improve the CFO estimation performance by taking the power average over a series of OFDM symbols.The effectiveness of the TO estimation algorithm,and both the DA and BL CFO estimation algorithms are verified and demonstrated in both simulations and experiments.展开更多
Constant envelope orthogonal frequency division multiplexing(CE-OFDM) is a waveform that can achieve 0d B peak-to-average power ratio and avoid the signal distortion caused by the nonlinear power amplifi er. However, ...Constant envelope orthogonal frequency division multiplexing(CE-OFDM) is a waveform that can achieve 0d B peak-to-average power ratio and avoid the signal distortion caused by the nonlinear power amplifi er. However, the carrier frequency offset(CFO) in CE-OFDM systems can cause errors at phase unwrapper module. In this paper, a CFO estimation scheme is proposed for CEOFDM in satellite communication system. As the null subcarrier is inherent in the conjugate symmetric symbol structure at the transmitter, the proposed scheme uses the null subcarrier as prior information to estimate the CFO at the receiver. The ideal estimation range of normalized CFO is obtained by mathematical analysis. Simulation results show that the proposed scheme can estimate the CFO accurately under additive white Gaussian noise(AWGN) channel and multipath fading channel, especially for moderate and high signal-to-noise ratio(SNR).展开更多
An efficient scheme of integer frequency offset estimate for orthogonal frequency division multiplexing （OFDM） systems is proposed based on a training symbol with several identicalparts. In this scheme, the received...An efficient scheme of integer frequency offset estimate for orthogonal frequency division multiplexing （OFDM） systems is proposed based on a training symbol with several identicalparts. In this scheme, the received training symbol is first reshaped into several sub-symbols.It shows that the reshaping process in-troduees time diversity multiplexing.After a special fast Fourier transform （FFT） algorithm is applied to the sub-symbol,the integer frequency is estimated by finding the maximum magnitude of the resulting fre-quency domain signal.To improve the estimate performance,diversity combining methods are presented to makefull use of the multiple frequency domain sub-symbols.Compared to the traditional scheme, theproposed one has an improved estimate performance demonstrated by the computation simulation, while maintaining a very low complexity.展开更多
The problem of estimating the carrier frequency offsets in Multiple-Input Multiple-Output (MIMO) systems with distributed transmit antennas is addressed. It is supposed that the transmit antennas are distributed while...The problem of estimating the carrier frequency offsets in Multiple-Input Multiple-Output (MIMO) systems with distributed transmit antennas is addressed. It is supposed that the transmit antennas are distributed while the receive antennas are still centralized, and the general case where both the time delays and the frequency offsets are possibly different for each transmit antenna is considered. The channel is supposed to be frequency flat, and the macroscopic fading is also taken into consideration. A carrier frequency offset estimator based on Maximum Likelihood (ML) is proposed, which can separately estimate the frequency offset for each transmit antenna and exploit the spatial diversity. The Cramer-Rao Bound (CRB) for synchronous MIMO (i.e., the time delays for each transmit antenna are all equal) is also derived. Simulation results are given to illustrate the per- formance of the estimator and compare it with the CRB. It is shown that the estimator can provide satisfactory frequency offset estimates and its performance is close to the CRB for the Signal-to-Noise Ratio (SNR) below 20dB.展开更多
The operating frequency accuracy of the local oscillators is critical for the overall system performance in the communication systems.However,the high-precision oscillators could be too expensive for civil application...The operating frequency accuracy of the local oscillators is critical for the overall system performance in the communication systems.However,the high-precision oscillators could be too expensive for civil applications.In this paper,we propose a model-free adaptive frequency calibration framework for a voltage-controlled crystal oscillator(VCO)equipped with a time to digital converter(TDC),which can significantly improve the frequency accuracy of the VCO thus calibrated.The idea is to utilize a high-precision TDC to directly measure the VCO period which is then passed to a model-free method for working frequency calibration.One advantage of this method is that the working frequency calibration employs the system history of input/output(I/O)data,instead of establishing an accurate VCO voltagecontrolled oscillator model.Another advantage is the lightweight calibration method with low complexity such that it can be implemented on an MCU with limited computation capabilities.Experimental results show that the proposed calibration method can improve the frequency accuracy of a VCO from±20 ppm to±10 ppb,which indicates the promise of the modelfree adaptive frequency calibrator for VCOs.展开更多
Worldwide Interoperability for Microwave Access(WiMAX)trusts Multiple Input Multiple Output-Orthogonal Frequency Division Multiplexing(MIMO-OFDM)combination for the deployment of physical layer functions and for conne...Worldwide Interoperability for Microwave Access(WiMAX)trusts Multiple Input Multiple Output-Orthogonal Frequency Division Multiplexing(MIMO-OFDM)combination for the deployment of physical layer functions and for connecting the medium access control to the wireless media.Even though Orthogonal Frequency Division Multiplexing(OFDM)facilitates reliable digital broadband transmission in the fading wireless channels,the presence of synchro-nization errors in the form of Carrier Frequency Offset(CFO)and Time Offset(TO)adversely affect the performance of OFDM based physical layers.The objective of this work is to improve the accuracy of the frequency and the time offset estimation in the WiMAX physical layer.A method to enhance the synchro-nization accuracy byfine-tuning the merit factor of the preamble sequence is sug-gested in this paper.Also,a new preamble with improved synchronization accuracy is proposed for the WiMAX system.The performance of the proposed preamble is evaluated in a Rayleigh fading channel and the results of simulations show that the Mean Square Error(MSE)in offset estimation is significantly reduced and it outperforms the standard WiMAX preamble.展开更多
A dual-band direct-conversion WLAN transceiver baseband compliant with the IEEE 802.11 a/b/g standards is described. Several critical techniques for receiver DC offset compensation and transmitter carrier leakage reje...A dual-band direct-conversion WLAN transceiver baseband compliant with the IEEE 802.11 a/b/g standards is described. Several critical techniques for receiver DC offset compensation and transmitter carrier leakage rejection calibration are presented that enable the direct-conversion architecture to meet all WLAN specifications. The receiver baseband VGA provides 62 dB gain range with steps of 2 dB and a DC offset cancellation circuit is introduced to remove the offset from layout and self-mixing. The calibration loop achieves constant high-pass pole when gain changes; and a fast response time by programming the pole to 1 MHz during preamble and to 30 kHz during receiving data. The transmitter baseband employs an auto-calibration loop with on-chip AD and DA to suppress the carrier leakage, and AD can be powered down after calibration to save power consumption. The chip consumes 17.52 mA for RX baseband VGA and DCOC, and 8.3 mA for TX carrier leakage calibration （5.88 mA after calibration） from 2.85 V supply. Implemented in a 0.35μm SiGe technology, they occupy 0.68 mm^2 and 0.18 mma die size respectively.展开更多
基金supported by the Reasearch Fund for the Visiting Scholar Program by the China Scholarship Council(2011631504)The U.S.Science Foundation(CNS-1205665)+1 种基金the Fundamental Research Funds for the Central Universities(201112G020,201212G012)the National Natural Science Foundation of China(41176032)
文摘The carrier frequency offset（CFO）and impulse noise always affect the performance of underwater acoustic communication_systems.The CFO and impulse noise could be estimated by using the null subcarriers to cancel the effects of the two types of interference.The null subcarriers estimation methods include optimal separate estimation and joint estimation.The separate estimation firstly estimates the CFO value and then estimates the impulse noise value.However,the CFO and impulse noise always affect each other when either of them is estimated separately.The performance could be improved by using the joint estimation.The results of simulations and experiments have showed that these two optimization methods have good performance and the joint estimation has better performance than the separate estimation method.There is 3 dB performance gain at the BER value of 10^（-2）when using the joint estimation method.Thus these methods could improve the system robustness by using the CFO compensation and impulse noise suppression.
基金supported by the National Natural Science Foundation of China(No.91438114,No.61372111 and No.61601045)
文摘Spectral efficiency and energy efficiency are two important performance indicators of satellite systems. The Quasi-Constant Envelope Orthogonal Frequency Division Multiplexing(QCE-OFDM) technique can achieve both high spectral efficiency and low peak-to-average power ratio(PAPR). Therefore, the QCE-OFDM technique is considered as a promising candidate multi-carrier technique for satellite systems. However, the Doppler effect will cause the carrier frequency offset(CFO), and the non-ideal oscillator will cause the carrier phase offset(CPO) in satellite systems. The CFO and CPO will further result in the bit-error-rate(BER) performance degradation. Hence, it is important to estimate and compensate the CFO and CPO. This paper analyzes the effects of both CFO and CPO in QCE-OFDM satellite systems. Furthermore, we propose a joint CFO and CPO estimation method based on the pilot symbols in the frequency domain. In addition, the optimal pilot symbol structure with different pilot overheads is designed according to the minimum Cramer-Rao bound(CRB) criterion. Simulation results show that the estimation accuracy of the proposed method is close to the CRB.
文摘This paper presents the architectures, algorithms, and implementation considerations of the digital phase locked loop (DPLL) used for burst-mode packet DS-CDMA receivers. As we know, carrier offset is a rather challenging problem in CDMA system. According to different applications, different DPLL forms should be adopted to correct different maximum carrier offset in CDMA systems. One classical DPLL and two novel DPLL forms are discussed in the paper. The acquisition range of carrier offset can be widened by using the two novel DPLL forms without any performance degradation such as longer acquisition time or larger variance of the phase error. The maximum acquisition range is 1/(4T), where T is the symbol period. The design can be implemented by FPGA directly.
文摘In this paper,we review our joint timing and frequency synchronization algorithms in coherent optical orthogonal frequency division multiplexing(CO-OFDM)systems.We first present a timing estimation method by designing the pattern of the training symbol,whose timing metric has a sharp and clear peak,to ensure accurate timing offset(TO)estimation performance.Then we provide both data-aided(DA)and blind(BL)approaches to estimate the carrier frequency offset(CFO).For the DA algorithm,we utilize the same training symbol structure as the timing estimation does,while for the BL algorithm,we utilize the zero-subcarrier power(ZSP)to achieve full-range CFO estimation.Note that our joint timing and frequency synchronization approaches require only one OFDM symbol,which ensure not only the data transmission efficiency,but also the TO and CFO estimation performance.A modified BL ZSP algorithm is proposed to further improve the CFO estimation performance by taking the power average over a series of OFDM symbols.The effectiveness of the TO estimation algorithm,and both the DA and BL CFO estimation algorithms are verified and demonstrated in both simulations and experiments.
基金supported by the National Natural Science Foundation of China(No.61601045,No.91438114 and No.61372111)
文摘Constant envelope orthogonal frequency division multiplexing(CE-OFDM) is a waveform that can achieve 0d B peak-to-average power ratio and avoid the signal distortion caused by the nonlinear power amplifi er. However, the carrier frequency offset(CFO) in CE-OFDM systems can cause errors at phase unwrapper module. In this paper, a CFO estimation scheme is proposed for CEOFDM in satellite communication system. As the null subcarrier is inherent in the conjugate symmetric symbol structure at the transmitter, the proposed scheme uses the null subcarrier as prior information to estimate the CFO at the receiver. The ideal estimation range of normalized CFO is obtained by mathematical analysis. Simulation results show that the proposed scheme can estimate the CFO accurately under additive white Gaussian noise(AWGN) channel and multipath fading channel, especially for moderate and high signal-to-noise ratio(SNR).
文摘An efficient scheme of integer frequency offset estimate for orthogonal frequency division multiplexing （OFDM） systems is proposed based on a training symbol with several identicalparts. In this scheme, the received training symbol is first reshaped into several sub-symbols.It shows that the reshaping process in-troduees time diversity multiplexing.After a special fast Fourier transform （FFT） algorithm is applied to the sub-symbol,the integer frequency is estimated by finding the maximum magnitude of the resulting fre-quency domain signal.To improve the estimate performance,diversity combining methods are presented to makefull use of the multiple frequency domain sub-symbols.Compared to the traditional scheme, theproposed one has an improved estimate performance demonstrated by the computation simulation, while maintaining a very low complexity.
基金the National Natural Science Foundation of China (No. 60272009, No. 60572090, No. 60472045, No. 60496313 and No. 60602009).
文摘The problem of estimating the carrier frequency offsets in Multiple-Input Multiple-Output (MIMO) systems with distributed transmit antennas is addressed. It is supposed that the transmit antennas are distributed while the receive antennas are still centralized, and the general case where both the time delays and the frequency offsets are possibly different for each transmit antenna is considered. The channel is supposed to be frequency flat, and the macroscopic fading is also taken into consideration. A carrier frequency offset estimator based on Maximum Likelihood (ML) is proposed, which can separately estimate the frequency offset for each transmit antenna and exploit the spatial diversity. The Cramer-Rao Bound (CRB) for synchronous MIMO (i.e., the time delays for each transmit antenna are all equal) is also derived. Simulation results are given to illustrate the per- formance of the estimator and compare it with the CRB. It is shown that the estimator can provide satisfactory frequency offset estimates and its performance is close to the CRB for the Signal-to-Noise Ratio (SNR) below 20dB.
文摘The operating frequency accuracy of the local oscillators is critical for the overall system performance in the communication systems.However,the high-precision oscillators could be too expensive for civil applications.In this paper,we propose a model-free adaptive frequency calibration framework for a voltage-controlled crystal oscillator(VCO)equipped with a time to digital converter(TDC),which can significantly improve the frequency accuracy of the VCO thus calibrated.The idea is to utilize a high-precision TDC to directly measure the VCO period which is then passed to a model-free method for working frequency calibration.One advantage of this method is that the working frequency calibration employs the system history of input/output(I/O)data,instead of establishing an accurate VCO voltagecontrolled oscillator model.Another advantage is the lightweight calibration method with low complexity such that it can be implemented on an MCU with limited computation capabilities.Experimental results show that the proposed calibration method can improve the frequency accuracy of a VCO from±20 ppm to±10 ppb,which indicates the promise of the modelfree adaptive frequency calibrator for VCOs.
文摘Worldwide Interoperability for Microwave Access(WiMAX)trusts Multiple Input Multiple Output-Orthogonal Frequency Division Multiplexing(MIMO-OFDM)combination for the deployment of physical layer functions and for connecting the medium access control to the wireless media.Even though Orthogonal Frequency Division Multiplexing(OFDM)facilitates reliable digital broadband transmission in the fading wireless channels,the presence of synchro-nization errors in the form of Carrier Frequency Offset(CFO)and Time Offset(TO)adversely affect the performance of OFDM based physical layers.The objective of this work is to improve the accuracy of the frequency and the time offset estimation in the WiMAX physical layer.A method to enhance the synchro-nization accuracy byfine-tuning the merit factor of the preamble sequence is sug-gested in this paper.Also,a new preamble with improved synchronization accuracy is proposed for the WiMAX system.The performance of the proposed preamble is evaluated in a Rayleigh fading channel and the results of simulations show that the Mean Square Error(MSE)in offset estimation is significantly reduced and it outperforms the standard WiMAX preamble.
文摘A dual-band direct-conversion WLAN transceiver baseband compliant with the IEEE 802.11 a/b/g standards is described. Several critical techniques for receiver DC offset compensation and transmitter carrier leakage rejection calibration are presented that enable the direct-conversion architecture to meet all WLAN specifications. The receiver baseband VGA provides 62 dB gain range with steps of 2 dB and a DC offset cancellation circuit is introduced to remove the offset from layout and self-mixing. The calibration loop achieves constant high-pass pole when gain changes; and a fast response time by programming the pole to 1 MHz during preamble and to 30 kHz during receiving data. The transmitter baseband employs an auto-calibration loop with on-chip AD and DA to suppress the carrier leakage, and AD can be powered down after calibration to save power consumption. The chip consumes 17.52 mA for RX baseband VGA and DCOC, and 8.3 mA for TX carrier leakage calibration （5.88 mA after calibration） from 2.85 V supply. Implemented in a 0.35μm SiGe technology, they occupy 0.68 mm^2 and 0.18 mma die size respectively.
