This paper presents an experimental investigation of laser welding low carbon galvanized steel in butt-joint configurations. The experimental work is focused on the effects of various laser welding parameters on the w...This paper presents an experimental investigation of laser welding low carbon galvanized steel in butt-joint configurations. The experimental work is focused on the effects of various laser welding parameters on the welds quality. The investigations are based on a structured experimental design using the Taguchi method. Welding experiments are conducted using a 3 kW Nd:YAG laser source. The selected laser welding parameters (laser power, welding speed, laser fiber diameter, gap between sheets and sheet thickness) are combined and used to evaluate the variation of four weld quality attributes (bead width, penetration depth, underfill and hardness) and to identify the possible relationship between welding parameters and weld physical and geometrical attributes. The effects of these parameters are studied using ANOVA to find their contributions to the variation of different weld characteristics. Plots of the main effects and the interaction effects are also used to understand the influence of the welding parameters. The results reveal that all welding parameters are relevant to bead width (BDW) and depth of penetration (DOP) with a relative predominance of laser power and welding speed. The effect of laser fiber diameter on penetration depth is insignificant. Typical gap-dependent weld shapes show that a small gap results in a narrower and deeper weld. Due to the standard sheared edge, an underfill between 5% and 10% occurs for no-gap experiments. The resulting hardness values are relatively similar for all the experimental tests.展开更多
In this investigation, hybrid laser/arc welding （HLAW） was employed to join 8-mm-thick high-strength quenched and tempered steel （HSQTS） plates in the butt- and T-joint configurations. The influences of welding pa...In this investigation, hybrid laser/arc welding （HLAW） was employed to join 8-mm-thick high-strength quenched and tempered steel （HSQTS） plates in the butt- and T-joint configurations. The influences of welding parame- ters, such as laser power, welding speed, stand-off distance （SD） between the arc of gas metal arc welding, and the laser heat source on the weld quality and mechanical properties of joints, were studied to obtain non-porous and crack-free fully-penetrated welds. The weld microstructure, cross- section, and mechanical properties were evaluated by an optical microscope, and microhardness and tensile tests. In addition, a finite element model was developed to investigate the thermal history and molten pool geometry of the HLAW process to join the HSQTS. The numerical study demon- strated that the SD had a paramount role in good synergy between the heat sources and the stability of the keyhole. For the butt-joint configuration, the results showed that, at a higher welding speed （35 mm/s） and optimum SD between the arc and laser, a fully-penetrated sound weld could be achieved. A non-porous weld in the T-joint configuration was obtained at a lower welding speed （10 mm/s）. Microstructural evaluations indicated that the formation of residual austenite and the continuous network of martensitic structure along the grain boundary through the heat affected zone were the primary reasons of the softening behavior of this area. This was confirmed by the sharp hardness reduction and failure behavior of the tensile coupons in this area.展开更多
Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate...Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO<sub>2</sub> Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.展开更多
文摘This paper presents an experimental investigation of laser welding low carbon galvanized steel in butt-joint configurations. The experimental work is focused on the effects of various laser welding parameters on the welds quality. The investigations are based on a structured experimental design using the Taguchi method. Welding experiments are conducted using a 3 kW Nd:YAG laser source. The selected laser welding parameters (laser power, welding speed, laser fiber diameter, gap between sheets and sheet thickness) are combined and used to evaluate the variation of four weld quality attributes (bead width, penetration depth, underfill and hardness) and to identify the possible relationship between welding parameters and weld physical and geometrical attributes. The effects of these parameters are studied using ANOVA to find their contributions to the variation of different weld characteristics. Plots of the main effects and the interaction effects are also used to understand the influence of the welding parameters. The results reveal that all welding parameters are relevant to bead width (BDW) and depth of penetration (DOP) with a relative predominance of laser power and welding speed. The effect of laser fiber diameter on penetration depth is insignificant. Typical gap-dependent weld shapes show that a small gap results in a narrower and deeper weld. Due to the standard sheared edge, an underfill between 5% and 10% occurs for no-gap experiments. The resulting hardness values are relatively similar for all the experimental tests.
文摘In this investigation, hybrid laser/arc welding （HLAW） was employed to join 8-mm-thick high-strength quenched and tempered steel （HSQTS） plates in the butt- and T-joint configurations. The influences of welding parame- ters, such as laser power, welding speed, stand-off distance （SD） between the arc of gas metal arc welding, and the laser heat source on the weld quality and mechanical properties of joints, were studied to obtain non-porous and crack-free fully-penetrated welds. The weld microstructure, cross- section, and mechanical properties were evaluated by an optical microscope, and microhardness and tensile tests. In addition, a finite element model was developed to investigate the thermal history and molten pool geometry of the HLAW process to join the HSQTS. The numerical study demon- strated that the SD had a paramount role in good synergy between the heat sources and the stability of the keyhole. For the butt-joint configuration, the results showed that, at a higher welding speed （35 mm/s） and optimum SD between the arc and laser, a fully-penetrated sound weld could be achieved. A non-porous weld in the T-joint configuration was obtained at a lower welding speed （10 mm/s）. Microstructural evaluations indicated that the formation of residual austenite and the continuous network of martensitic structure along the grain boundary through the heat affected zone were the primary reasons of the softening behavior of this area. This was confirmed by the sharp hardness reduction and failure behavior of the tensile coupons in this area.
文摘Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO<sub>2</sub> Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.
