The general hot deformation process consists of two steps, hot pressing and die-upsetting in order to obtain the anisotropic NdFeB magnet. This is the first report that the high anisotropy NdFeB magnets can be fabrica...The general hot deformation process consists of two steps, hot pressing and die-upsetting in order to obtain the anisotropic NdFeB magnet. This is the first report that the high anisotropy NdFeB magnets can be fabricated by single stroke hot deforming the isotropic magnet. The magnetic properties of those materials are: coercivity iHc ～11 kOe, remanence Br ～12 kG, and the maximum energy product (BH)max ～28 MG.Oe.展开更多
Anisotropic NdFeB/SmFeN hybrid bonded magnets were prepared by warm compaction process under an orientation magnetic field of 22 kOe,mixing with anisotropic SmFeN powders in different addition and HDDR-NdFeB powders i...Anisotropic NdFeB/SmFeN hybrid bonded magnets were prepared by warm compaction process under an orientation magnetic field of 22 kOe,mixing with anisotropic SmFeN powders in different addition and HDDR-NdFeB powders in different coercivity.With the addition of 20 wt% SmFeN,the density and remanence of hybrid magnets increase from 5.58 g/cm~3,8.4 kGs to 6.02 g/cm~3,9.0 kGs,respectively.And as the addition amount of SmFeN powders varies from 20 wt% to 40 wt%,the maximum energy product changes less than 0.5 MGOe.In addition,the magnetization process and the interactions between two powders were studied.It is found that the magnetization process of anisotropic NdFeB powders shows distinction in different initial states.The addition of SmFeN powders promotes the rotation of NdFeB powders together with applied field,which is beneficial to the degree of alignment of NdFeB powders.Because of the micron-sized long range coupling effect,the coercivity of hybrid magnets decreases slowly with the increase of low coercivity SmFeN.Meanwhile,the magnetization process of hybrid magnets is different from pure magnets,it increases rapidly at low field and then slowly,next leads to rapidity again and achieves the saturation magnetization finally.展开更多
Texture evolution in nanocomposite Nd_2Fe_ 14B/α-Fe magnets prepared by direct melt spinning was investigated. The free surface and wheel-contacted surface exhibit different texture direction. Modification of composi...Texture evolution in nanocomposite Nd_2Fe_ 14B/α-Fe magnets prepared by direct melt spinning was investigated. The free surface and wheel-contacted surface exhibit different texture direction. Modification of composition not only enhances magnetic properties, but also changes texture direction of the ribbon. Low temperature heat treatment can increase the magnetic properties to some extent, and high temperature annealing decreases the magnetic properties. Both low and high temperature heat treatment have effects on grain orientation, but the difference still exists between the two surfaces of the ribbon. So it is infeasibility to prepare anisotropic Nd_2Fe_ 14B/α-Fe nanocomposite magnets by direct melt spinning.展开更多
We study the coutrol of gate voltage over the magnetization of a single-molecule magnet （SMM） weakly coupled to a ferromagnetic and a normal metal electrode in the presence of the temperature gradient between two el...We study the coutrol of gate voltage over the magnetization of a single-molecule magnet （SMM） weakly coupled to a ferromagnetic and a normal metal electrode in the presence of the temperature gradient between two electrodes. It is demonstrated that the SMM＇s magnetization can change periodically with periodic gate voltage due to the driving oI the temperature gradient. Under an appropriate matching of the electrode polarization, the temperature difference and the pulse width of gate voltage, the SMM＇s magnetization can be completely reversed in a period of gate voltage. The corresponding flipping time can be controlled by the system parameters. In addition, we also investigate the tunneling anisotropic magnetoresistance （TAMFt） of the device in the steady state when the ferromagnetic electrode is noncollinear with the easy axis of the SMM, and show the jump characteristic of the TAMR.展开更多
The waste sintered Nd-Fe-B magnets were regenerated as magnetic powders via manually crushing （MC） or hydrogen decrepitation （HD） to fabricate anisotropic bonded magnets. Effect of size distribution on the magneti...The waste sintered Nd-Fe-B magnets were regenerated as magnetic powders via manually crushing （MC） or hydrogen decrepitation （HD） to fabricate anisotropic bonded magnets. Effect of size distribution on the magnetic properties of the regenerated magnetic MC and HD powders was investigated. For the MC powders, as the particle size decreased, the remanence （Br） increased first, and then decreased again, while the coercivity （Hci） dropped monotonically. The powders with particle size in the range of 200-450μm possessed the best magnetic properties ofBr of 1.22 T and Hci of 875.6 kAJm. The corresponding bonded magnet exhibited magnetic properties ofBr of 0.838 T, Hci of 940.9 kA/m, and （BH）max of 91.4 kJ/m^3, respectively. On the other hand, the liD powders with particle size range of 200-450 μm bore the best magnetic properties Of Br of 1.24 T and Hci of 860.4 kA/m. Compared with magnetic properties of the waste magnet, the powders retained 93.9% of Br and 70.0% of Hci, respectively. The bonded magnet produced from HD powders possessed Br of 0.9 T, Hci of 841.4 kA/m, and （BH）max of 111.6 kJ/m^3, indicating its good potential in practical applications.展开更多
Anisotropic NdFeB/SmCoCuFeZr composite bonded magnets were prepared by warm compaction process. The effects of adding SmCoCuFeZr magnetic powder on the properties of anisotropic bonded NdFeB magnet were investigated i...Anisotropic NdFeB/SmCoCuFeZr composite bonded magnets were prepared by warm compaction process. The effects of adding SmCoCuFeZr magnetic powder on the properties of anisotropic bonded NdFeB magnet were investigated in this work. The results show that, both magnetic properties and temperature stability of the bonded magnet can be improved by adding fine SmCoCuFeZr magnetic powder. In the present study, the optimal content of SmCoCuFeZr magnetic powder was about 20 wt.%, in this case, the Br, Hcj, and（BH）maxof the NdFeB/SmCoCuFeZr composite magnet achieved 0.943 T, 1250 kA/m, and168 kJ/m^3, respectively.展开更多
文摘The general hot deformation process consists of two steps, hot pressing and die-upsetting in order to obtain the anisotropic NdFeB magnet. This is the first report that the high anisotropy NdFeB magnets can be fabricated by single stroke hot deforming the isotropic magnet. The magnetic properties of those materials are: coercivity iHc ～11 kOe, remanence Br ～12 kG, and the maximum energy product (BH)max ～28 MG.Oe.
基金supported by the National Key Research and Development Program of China (2021YFB3500202,2021YFB3500201)the Beijing Youth Top-notch Team Support Project of China (2018000021223TD10)+2 种基金the Beijing NOVA Program (Z211100002121092)the Natural Science Foundation of Hebei Province (E2021103006)the Hebei Province International Science and Technology Cooperation Base Construction Project of China (20591002D)。
文摘Anisotropic NdFeB/SmFeN hybrid bonded magnets were prepared by warm compaction process under an orientation magnetic field of 22 kOe,mixing with anisotropic SmFeN powders in different addition and HDDR-NdFeB powders in different coercivity.With the addition of 20 wt% SmFeN,the density and remanence of hybrid magnets increase from 5.58 g/cm~3,8.4 kGs to 6.02 g/cm~3,9.0 kGs,respectively.And as the addition amount of SmFeN powders varies from 20 wt% to 40 wt%,the maximum energy product changes less than 0.5 MGOe.In addition,the magnetization process and the interactions between two powders were studied.It is found that the magnetization process of anisotropic NdFeB powders shows distinction in different initial states.The addition of SmFeN powders promotes the rotation of NdFeB powders together with applied field,which is beneficial to the degree of alignment of NdFeB powders.Because of the micron-sized long range coupling effect,the coercivity of hybrid magnets decreases slowly with the increase of low coercivity SmFeN.Meanwhile,the magnetization process of hybrid magnets is different from pure magnets,it increases rapidly at low field and then slowly,next leads to rapidity again and achieves the saturation magnetization finally.
文摘Texture evolution in nanocomposite Nd_2Fe_ 14B/α-Fe magnets prepared by direct melt spinning was investigated. The free surface and wheel-contacted surface exhibit different texture direction. Modification of composition not only enhances magnetic properties, but also changes texture direction of the ribbon. Low temperature heat treatment can increase the magnetic properties to some extent, and high temperature annealing decreases the magnetic properties. Both low and high temperature heat treatment have effects on grain orientation, but the difference still exists between the two surfaces of the ribbon. So it is infeasibility to prepare anisotropic Nd_2Fe_ 14B/α-Fe nanocomposite magnets by direct melt spinning.
基金Supported by the National Natural Science Foundation of China under Grant No 11274208
文摘We study the coutrol of gate voltage over the magnetization of a single-molecule magnet （SMM） weakly coupled to a ferromagnetic and a normal metal electrode in the presence of the temperature gradient between two electrodes. It is demonstrated that the SMM＇s magnetization can change periodically with periodic gate voltage due to the driving oI the temperature gradient. Under an appropriate matching of the electrode polarization, the temperature difference and the pulse width of gate voltage, the SMM＇s magnetization can be completely reversed in a period of gate voltage. The corresponding flipping time can be controlled by the system parameters. In addition, we also investigate the tunneling anisotropic magnetoresistance （TAMFt） of the device in the steady state when the ferromagnetic electrode is noncollinear with the easy axis of the SMM, and show the jump characteristic of the TAMR.
基金Project supported by the National High Technology Research and Development Program of China(2012AA063201)the Importation and Development of High-Caliber Talents Project of Beijing Municipal Institutions
文摘The waste sintered Nd-Fe-B magnets were regenerated as magnetic powders via manually crushing （MC） or hydrogen decrepitation （HD） to fabricate anisotropic bonded magnets. Effect of size distribution on the magnetic properties of the regenerated magnetic MC and HD powders was investigated. For the MC powders, as the particle size decreased, the remanence （Br） increased first, and then decreased again, while the coercivity （Hci） dropped monotonically. The powders with particle size in the range of 200-450μm possessed the best magnetic properties ofBr of 1.22 T and Hci of 875.6 kAJm. The corresponding bonded magnet exhibited magnetic properties ofBr of 0.838 T, Hci of 940.9 kA/m, and （BH）max of 91.4 kJ/m^3, respectively. On the other hand, the liD powders with particle size range of 200-450 μm bore the best magnetic properties Of Br of 1.24 T and Hci of 860.4 kA/m. Compared with magnetic properties of the waste magnet, the powders retained 93.9% of Br and 70.0% of Hci, respectively. The bonded magnet produced from HD powders possessed Br of 0.9 T, Hci of 841.4 kA/m, and （BH）max of 111.6 kJ/m^3, indicating its good potential in practical applications.
基金Project supported by the Natural Science Foundation of Jiangsu Province,China(BK20171408)the Graduate Student Innovation Foundation of Jiangsu Province(201711276005Z)Scientific Foundation of Nanjing Institute of Technology(CKJB201402,and YKJ201506)
文摘Anisotropic NdFeB/SmCoCuFeZr composite bonded magnets were prepared by warm compaction process. The effects of adding SmCoCuFeZr magnetic powder on the properties of anisotropic bonded NdFeB magnet were investigated in this work. The results show that, both magnetic properties and temperature stability of the bonded magnet can be improved by adding fine SmCoCuFeZr magnetic powder. In the present study, the optimal content of SmCoCuFeZr magnetic powder was about 20 wt.%, in this case, the Br, Hcj, and（BH）maxof the NdFeB/SmCoCuFeZr composite magnet achieved 0.943 T, 1250 kA/m, and168 kJ/m^3, respectively.
