In order to reduce the impact of eutrophication caused by agricultural residues （i.e., excess nitrate） in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic ...In order to reduce the impact of eutrophication caused by agricultural residues （i.e., excess nitrate） in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic sorbent using wheat straw. Its structural characteristics and adsorption properties for nitrate removal from aqueous solution were investigated. The results indicate that the yield of the prepared anionic sorbent, the total exchange capacity, and the maximum adsorption capacity were 350%, 2.57 mEq/g, and 2.08 mmol/g, respectively. The Freundlich isotherm mode is more suitable than the Langmuir mode and the adsorption process accords with the first order reaction kinetic rate equation. When multiple anions （SO4^2-, H2PO4^-, NO3^-, and NO2^-） were present, the isotherm mode of prepared anionic sorbent for nitrate was consistent with Freundlich mode; however, the capacity of nitrate adsorption was reduced by 50%. In alkaline solutions, about 90% of adsorbed nitrate ions could be desorbed from prepared anionic sorbent. The results of this study confirmed that the wheat straw anionic sorbent can be used as an excellent nitrate sorbent that removes nitrate from aqueous solutions.展开更多
A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals includi...A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals including coagulants and chemicals for pH adjustment is costly for treating this wastewater. The objective of this study was to evaluate the feasibility of reusing the aluminum sulfate （alum） sludge as a coagulant or as a coagulation aid so that the fresh alum dosage can be minimized or the removal efficiency can be enhanced. The experiments were conducted in a jar-test apparatus simulating the coagulation-flocculation process for simultaneous removals of organic matters, anionic surfactants, suspended solids, and turbidity. At the optimum initial pH value of 10 and the fresh alum concentration of 400 mg/L, the total suspended solids （TSS）, total chemical oxygen demand （TCOD）, total anionic surfactants, and turbidity removal efficiencies were 71.5%, 76.4%, 95.4%, and 98.2%, respectively. The addition of alum sludge as a coagulant alone without any fresh alum addition could significantly remove the turbidity, TCOD, and anionic surfactants. The TSS was left in the supernatants after the settling period, but would subsequently be removed by adding the fresh alum. The TSS, TCOD, and turbidity removal efficiencies were also enhanced when both the alum sludge and the fresh alum were employed. The TCOD removal efficiency over 80% has been accomplished, which has never fulfilled by using the fresh alum alone. It is concluded that the alum sludge could be reused for the treatment of industrial wastewater generated by the consumer products industry.展开更多
The hydroxyl-terminated polybutadiene （HTPB） possessing high content of 1,4-units was synthesized by anionic polymerization of butadiene, using alkyllithium containing silicon-protected hydroxyl group as initiator a...The hydroxyl-terminated polybutadiene （HTPB） possessing high content of 1,4-units was synthesized by anionic polymerization of butadiene, using alkyllithium containing silicon-protected hydroxyl group as initiator and cyclohexane as solvent. The polymers were characterized by GPC, IR and 1H-NMR. The mechanical properties of cured films were also evaluated. The results show that the content of 1,4-units for HTPBs made by anionic polymerization reaches up to 90%. The molecular weight distribution is very narrow （〈 1.05）. The functionality of hydroxyl groups approaches 2. Compared with free radical HTPB, the elongation at break of anionic HTPB films increased by 70%, while the tensile strength remained nearly unchanged. This new HTPB can be very useful in solid propellant.展开更多
基金Project supported by the Key Science Project of Environmental Protection Foundation of Shandong Government(No.(2006)005).
文摘In order to reduce the impact of eutrophication caused by agricultural residues （i.e., excess nitrate） in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic sorbent using wheat straw. Its structural characteristics and adsorption properties for nitrate removal from aqueous solution were investigated. The results indicate that the yield of the prepared anionic sorbent, the total exchange capacity, and the maximum adsorption capacity were 350%, 2.57 mEq/g, and 2.08 mmol/g, respectively. The Freundlich isotherm mode is more suitable than the Langmuir mode and the adsorption process accords with the first order reaction kinetic rate equation. When multiple anions （SO4^2-, H2PO4^-, NO3^-, and NO2^-） were present, the isotherm mode of prepared anionic sorbent for nitrate was consistent with Freundlich mode; however, the capacity of nitrate adsorption was reduced by 50%. In alkaline solutions, about 90% of adsorbed nitrate ions could be desorbed from prepared anionic sorbent. The results of this study confirmed that the wheat straw anionic sorbent can be used as an excellent nitrate sorbent that removes nitrate from aqueous solutions.
基金the Research and Development Fund of the Faculty of Engineering,Burapha University(No.70/2551)for financial supports
文摘A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals including coagulants and chemicals for pH adjustment is costly for treating this wastewater. The objective of this study was to evaluate the feasibility of reusing the aluminum sulfate （alum） sludge as a coagulant or as a coagulation aid so that the fresh alum dosage can be minimized or the removal efficiency can be enhanced. The experiments were conducted in a jar-test apparatus simulating the coagulation-flocculation process for simultaneous removals of organic matters, anionic surfactants, suspended solids, and turbidity. At the optimum initial pH value of 10 and the fresh alum concentration of 400 mg/L, the total suspended solids （TSS）, total chemical oxygen demand （TCOD）, total anionic surfactants, and turbidity removal efficiencies were 71.5%, 76.4%, 95.4%, and 98.2%, respectively. The addition of alum sludge as a coagulant alone without any fresh alum addition could significantly remove the turbidity, TCOD, and anionic surfactants. The TSS was left in the supernatants after the settling period, but would subsequently be removed by adding the fresh alum. The TSS, TCOD, and turbidity removal efficiencies were also enhanced when both the alum sludge and the fresh alum were employed. The TCOD removal efficiency over 80% has been accomplished, which has never fulfilled by using the fresh alum alone. It is concluded that the alum sludge could be reused for the treatment of industrial wastewater generated by the consumer products industry.
文摘The hydroxyl-terminated polybutadiene （HTPB） possessing high content of 1,4-units was synthesized by anionic polymerization of butadiene, using alkyllithium containing silicon-protected hydroxyl group as initiator and cyclohexane as solvent. The polymers were characterized by GPC, IR and 1H-NMR. The mechanical properties of cured films were also evaluated. The results show that the content of 1,4-units for HTPBs made by anionic polymerization reaches up to 90%. The molecular weight distribution is very narrow （〈 1.05）. The functionality of hydroxyl groups approaches 2. Compared with free radical HTPB, the elongation at break of anionic HTPB films increased by 70%, while the tensile strength remained nearly unchanged. This new HTPB can be very useful in solid propellant.
