Torpedo anchors have been used in mooring systems for deep-water oil and gas projects owing to their prominent advantages, such as low cost and easy installation. The maximum force of torpedo anchors is crucial not on...Torpedo anchors have been used in mooring systems for deep-water oil and gas projects owing to their prominent advantages, such as low cost and easy installation. The maximum force of torpedo anchors is crucial not only to the safety and stability of vessels and other marine facilities, but also for an economical design. It is necessary to develop reliable formula for fast predicting their maximum inclined force of a torpedo anchor in cohesive beds. In this study, the maximum inclined force of a torpedo anchor vertically embedded in cohesive beds was extensively investigated. 316 sets of inclined pullout laboratory tests were carried out for 9 differently shaped torpedo anchors which were vertically embedded in different cohesive beds. The loading curves were automatically acquisitioned and their characteristics were analyzed. The load angle relative to the horizontal varied from 20° to 90°. A new formula for fast calculating the maximum inclined force of the torpedo anchor vertically embedded in cohesive beds was obtained based on force analysis and a nonlinear regression on the data from the present and other studies. Effect aspects on the tests are discussed and further studies are highlighted.展开更多
Rock anchors are a common safety measure for stabilising large-scale infrastructure,such as bridge towers,retaining walls,rock slopes and windmills.There are four principal failure modes for rock anchors:(a)tensile fa...Rock anchors are a common safety measure for stabilising large-scale infrastructure,such as bridge towers,retaining walls,rock slopes and windmills.There are four principal failure modes for rock anchors:(a)tensile failure of the steel anchor,(b)anchor-grout interface failure,(c)grout-rock interface failure,and(d)rock mass uplift.Field tests were performed in a limestone quarry.These tests were designed to test failure modes B and C through pullout.In the tests of failure mode B,the shear stress on the anchor-grout interface is the largest at the top of the grout column and attenuates towards the distal end for small loads.The shear stress becomes uniformly distributed when the applied load is approximately 50%of the ultimate pullout load.The anchors designed to test failure mode C were installed with an endplate and had a higher toughness than the straight bar anchors.The shear stress on the grout-rock interface is the largest at the endplate and attenuates upward before slip starts along the interface.When the ultimate pullout load is reached,and the grout column starts to slip,the shear stress is approximately constant.The bond shear strength on the anchor-grout interface was approximately 20%of the uniaxial compressive strength of the grout,and the bond strength of the grout-rock interface was around 5%for that of the grout.The grout-rock interface is likely determined by whichever is weaker,the grout or the rock.展开更多
基金financially supported by the Ministry of Education of China(Grant No.6141A02022337)
文摘Torpedo anchors have been used in mooring systems for deep-water oil and gas projects owing to their prominent advantages, such as low cost and easy installation. The maximum force of torpedo anchors is crucial not only to the safety and stability of vessels and other marine facilities, but also for an economical design. It is necessary to develop reliable formula for fast predicting their maximum inclined force of a torpedo anchor in cohesive beds. In this study, the maximum inclined force of a torpedo anchor vertically embedded in cohesive beds was extensively investigated. 316 sets of inclined pullout laboratory tests were carried out for 9 differently shaped torpedo anchors which were vertically embedded in different cohesive beds. The loading curves were automatically acquisitioned and their characteristics were analyzed. The load angle relative to the horizontal varied from 20° to 90°. A new formula for fast calculating the maximum inclined force of the torpedo anchor vertically embedded in cohesive beds was obtained based on force analysis and a nonlinear regression on the data from the present and other studies. Effect aspects on the tests are discussed and further studies are highlighted.
文摘Rock anchors are a common safety measure for stabilising large-scale infrastructure,such as bridge towers,retaining walls,rock slopes and windmills.There are four principal failure modes for rock anchors:(a)tensile failure of the steel anchor,(b)anchor-grout interface failure,(c)grout-rock interface failure,and(d)rock mass uplift.Field tests were performed in a limestone quarry.These tests were designed to test failure modes B and C through pullout.In the tests of failure mode B,the shear stress on the anchor-grout interface is the largest at the top of the grout column and attenuates towards the distal end for small loads.The shear stress becomes uniformly distributed when the applied load is approximately 50%of the ultimate pullout load.The anchors designed to test failure mode C were installed with an endplate and had a higher toughness than the straight bar anchors.The shear stress on the grout-rock interface is the largest at the endplate and attenuates upward before slip starts along the interface.When the ultimate pullout load is reached,and the grout column starts to slip,the shear stress is approximately constant.The bond shear strength on the anchor-grout interface was approximately 20%of the uniaxial compressive strength of the grout,and the bond strength of the grout-rock interface was around 5%for that of the grout.The grout-rock interface is likely determined by whichever is weaker,the grout or the rock.
