The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions...The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.展开更多
New strain induced melt activation（new SIMA） method was employed to prepare high-quality semisolid billet of AZ61 magnesium alloy.Optical microscopy and tensile test were used to study the microstructure and mechani...New strain induced melt activation（new SIMA） method was employed to prepare high-quality semisolid billet of AZ61 magnesium alloy.Optical microscopy and tensile test were used to study the microstructure and mechanical properties of the thixo-extruded component.The results showed that the optimal process parameters for achieving the complete filling status involved the applied pressure of 784 MPa,the pressure holding time of 90 s and the die temperature of 450 ℃.Compared to semisolid isothermal treatment,high mechanical properties such as the tensile strength of 300.5 MPa and elongation of 22% and fine microstructure were obtained in the thixo-extruded parts.With increasing the isothermal temperature and holding time,the tensile strength and elongation were increased firstly and then decreased.When the press pass was increased from 1 to 4,the tensile strength and elongation of the thixo-extruded parts were greatly enhanced and microstructure was refined obviously.展开更多
The nanocrystalline and amorphous Mg2Ni-type alloys with a chemical composition of （Mg24Ni10Cu2）100-xNdx （x=0, 5, 10, 15, 20） were fabricated by melt spinning technology. The effects of spinning rate on the struct...The nanocrystalline and amorphous Mg2Ni-type alloys with a chemical composition of （Mg24Ni10Cu2）100-xNdx （x=0, 5, 10, 15, 20） were fabricated by melt spinning technology. The effects of spinning rate on the structure and electrochemical hydrogen storage performance of the alloys were investigated. The as-spun Nd-free alloy displays an entire nanocrystalline structure, whereas the as-spun Nd-added alloys hold a nanocrystalline and amorphous structure, suggesting that the addition of Nd facilitates the glass forming of the Mg2Ni-type alloys. Increasing the spinning rate from 0 to 40 m/s gives rise to the discharge capacity growing from 42.5 to 100.6 mA·h/g for the x=0 alloy and from 86.4 to 452.8 mA·h/g for the x=10 alloy. And the cycle stability （S20） rises from 40.2%to 41.1%for the x=0 alloy and from 53.2%to 89.7%for the x=10 alloy, respectively.展开更多
The surface tension and specific heat of Ni-5%Sn alloy melt were measured by the oscillating drop method and the drop calorimetric method using electromagnetic levitation, respectively. The temperature coefficient of ...The surface tension and specific heat of Ni-5%Sn alloy melt were measured by the oscillating drop method and the drop calorimetric method using electromagnetic levitation, respectively. The temperature coefficient of surface tension is 6.43×10-4 N·m?1K?1 within the temperature regime of 1464-1931 K. The enthalpy change was measured in the temperature range from 1461 to 1986 K, and the average specific heat was obtained as 43.03 J·mol?1K?1. Some other thermophysical properties, such as viscosity, solute dif-fusion coefficient, density, thermal diffusivity and thermal conductivity of this alloy melt, were derived based on the experimentally measured surface tension and specific heat. Using these thermophysical parameters, the relation between solute trapping and under-cooling in rapidly solidified α-Ni was calculated, and the theoretical prediction shows a good agreement with experimental data.展开更多
Selective laser melting（SLM） was employed to fabricate Nb-37 Ti-13 Cr-2 Al-1 Si（at%）alloy, using pre-alloyed powders prepared by plasma rotating electrode processing（PREP）. A series of single tracks and single l...Selective laser melting（SLM） was employed to fabricate Nb-37 Ti-13 Cr-2 Al-1 Si（at%）alloy, using pre-alloyed powders prepared by plasma rotating electrode processing（PREP）. A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance.Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density（LED）, i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLMprocessing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys.展开更多
文摘The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.
基金Project(51075099) supported by the National Natural Science Foundation of ChinaProject(E201038) supported by the Natural Science Foundation of Heilongjiang Province,China+3 种基金Project(20090460884) supported by the China Postdoctoral Science FoundationProjects (HIT.NSRIF.2013007 and 2012038) supported by the Fundamental Research Funds for the Central Universities,ChinaProject (2011RFQXG010) supported by the Harbin City Young Scientists Foundation under the GrantProject(LBH-T1102) supported by the Specially Postdoctoral Science Foundation of Heilongjiang Province,China
文摘New strain induced melt activation（new SIMA） method was employed to prepare high-quality semisolid billet of AZ61 magnesium alloy.Optical microscopy and tensile test were used to study the microstructure and mechanical properties of the thixo-extruded component.The results showed that the optimal process parameters for achieving the complete filling status involved the applied pressure of 784 MPa,the pressure holding time of 90 s and the die temperature of 450 ℃.Compared to semisolid isothermal treatment,high mechanical properties such as the tensile strength of 300.5 MPa and elongation of 22% and fine microstructure were obtained in the thixo-extruded parts.With increasing the isothermal temperature and holding time,the tensile strength and elongation were increased firstly and then decreased.When the press pass was increased from 1 to 4,the tensile strength and elongation of the thixo-extruded parts were greatly enhanced and microstructure was refined obviously.
基金Projects (51161015,51371094) supported by the National Natural Science Foundation of ChinaProject (2011ZD10) supported by the Natural Science Foundation of Inner Mongolia,China
文摘The nanocrystalline and amorphous Mg2Ni-type alloys with a chemical composition of （Mg24Ni10Cu2）100-xNdx （x=0, 5, 10, 15, 20） were fabricated by melt spinning technology. The effects of spinning rate on the structure and electrochemical hydrogen storage performance of the alloys were investigated. The as-spun Nd-free alloy displays an entire nanocrystalline structure, whereas the as-spun Nd-added alloys hold a nanocrystalline and amorphous structure, suggesting that the addition of Nd facilitates the glass forming of the Mg2Ni-type alloys. Increasing the spinning rate from 0 to 40 m/s gives rise to the discharge capacity growing from 42.5 to 100.6 mA·h/g for the x=0 alloy and from 86.4 to 452.8 mA·h/g for the x=10 alloy. And the cycle stability （S20） rises from 40.2%to 41.1%for the x=0 alloy and from 53.2%to 89.7%for the x=10 alloy, respectively.
基金the National Natural Science Foundation of China (Grant Nos. 50121101, 50395105, 50271058, 50201013).
文摘The surface tension and specific heat of Ni-5%Sn alloy melt were measured by the oscillating drop method and the drop calorimetric method using electromagnetic levitation, respectively. The temperature coefficient of surface tension is 6.43×10-4 N·m?1K?1 within the temperature regime of 1464-1931 K. The enthalpy change was measured in the temperature range from 1461 to 1986 K, and the average specific heat was obtained as 43.03 J·mol?1K?1. Some other thermophysical properties, such as viscosity, solute dif-fusion coefficient, density, thermal diffusivity and thermal conductivity of this alloy melt, were derived based on the experimentally measured surface tension and specific heat. Using these thermophysical parameters, the relation between solute trapping and under-cooling in rapidly solidified α-Ni was calculated, and the theoretical prediction shows a good agreement with experimental data.
基金supported by the National Natural Science Foundation of China (Nos. 51471013 and 51571004)
文摘Selective laser melting（SLM） was employed to fabricate Nb-37 Ti-13 Cr-2 Al-1 Si（at%）alloy, using pre-alloyed powders prepared by plasma rotating electrode processing（PREP）. A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance.Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density（LED）, i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLMprocessing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys.
