In this paper, in situ （Ti, Nb）C particle （（Ti, Nb）Cp） reinforced Fe-based composite coatings were produced by laser cladding on the surface of the high carbon steel. The effects of heat input on the microstruct...In this paper, in situ （Ti, Nb）C particle （（Ti, Nb）Cp） reinforced Fe-based composite coatings were produced by laser cladding on the surface of the high carbon steel. The effects of heat input on the microstructure, distribution characteristics of particle, and mechanical properties of the coating were investigated. The results show that （Ti, Nb）C multiple carbide particle is synthesized during solidification of molten pool. The size of particle coarsens gradually, the area ratio of particle increases, and the amount of particles presents a non-monotonous variation with the increase in energy density. The mechanical properties of the coating are improved dramatically compared with those of the substrate, benefiting from its higher hardness and dispersed in situ （Ti, Nb）Cp in it. With the change in heat input, the mechanical performances of the coating vary except the hardness. When energy density is 1 × 10^5 J.mm-2, tensile strength and wear resistance of the coating achieve optimal value due to moderate content and size of the particle in the coating.展开更多
The influences of nitrogen content and austenitization temperature on Nb（C, N） precipitation in niobium micro-alloyed steels were studied by different methods： optical microscopy, tensile tests, scanning electron m...The influences of nitrogen content and austenitization temperature on Nb（C, N） precipitation in niobium micro-alloyed steels were studied by different methods： optical microscopy, tensile tests, scanning electron mi- croscopy, transmission electron microscopy, physicochemical phase analysis, and small-angle X-ray scattering. The results show that the strength of the steel with high nitrogen content is slightly higher than that of the steel with low nitrogen content. The increase in the nitrogen content does not result in the increase in the amount of Nb（C,N） precipitates, which mainly depends on the niobium content in the steel. The mass fraction of small-sized Nb（C, N） precipitates （1--10 nm） in the steel with high nitrogen content is less than that in the steel with low nitrogen con- tent. After austenitized at 1 150 ℃, a number of large cuboidal and needle-shaped particles are detected in the steel with high nitrogen content, whereas they dissolve after austenitized at 1 200 ℃ and the Nb（C,N） precipitates become finer in both steels. Furthermore, the results also show that part of the nitrogen in steel involves the formation of al- loyed cementite.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51275006)
文摘In this paper, in situ （Ti, Nb）C particle （（Ti, Nb）Cp） reinforced Fe-based composite coatings were produced by laser cladding on the surface of the high carbon steel. The effects of heat input on the microstructure, distribution characteristics of particle, and mechanical properties of the coating were investigated. The results show that （Ti, Nb）C multiple carbide particle is synthesized during solidification of molten pool. The size of particle coarsens gradually, the area ratio of particle increases, and the amount of particles presents a non-monotonous variation with the increase in energy density. The mechanical properties of the coating are improved dramatically compared with those of the substrate, benefiting from its higher hardness and dispersed in situ （Ti, Nb）Cp in it. With the change in heat input, the mechanical performances of the coating vary except the hardness. When energy density is 1 × 10^5 J.mm-2, tensile strength and wear resistance of the coating achieve optimal value due to moderate content and size of the particle in the coating.
基金Item Sponsored by the CITIC-CBMM Niobium Steel Research and Development Program of China(2013-D065)
文摘The influences of nitrogen content and austenitization temperature on Nb（C, N） precipitation in niobium micro-alloyed steels were studied by different methods： optical microscopy, tensile tests, scanning electron mi- croscopy, transmission electron microscopy, physicochemical phase analysis, and small-angle X-ray scattering. The results show that the strength of the steel with high nitrogen content is slightly higher than that of the steel with low nitrogen content. The increase in the nitrogen content does not result in the increase in the amount of Nb（C,N） precipitates, which mainly depends on the niobium content in the steel. The mass fraction of small-sized Nb（C, N） precipitates （1--10 nm） in the steel with high nitrogen content is less than that in the steel with low nitrogen con- tent. After austenitized at 1 150 ℃, a number of large cuboidal and needle-shaped particles are detected in the steel with high nitrogen content, whereas they dissolve after austenitized at 1 200 ℃ and the Nb（C,N） precipitates become finer in both steels. Furthermore, the results also show that part of the nitrogen in steel involves the formation of al- loyed cementite.
