Hot tearing is often a major casting defect in magnesium alloys and has a significant impact on the quality of their casting products.Hot tearing of magnesium alloys is a complex solidification phenomenon which is sti...Hot tearing is often a major casting defect in magnesium alloys and has a significant impact on the quality of their casting products.Hot tearing of magnesium alloys is a complex solidification phenomenon which is still not fully understood,it is of great importance to investigate the hot tearing behaviour of magnesium alloys.This review attempts to summarize the investigations on hot tearing of magnesium alloys over the past decades.The hot tearing criteria including recently developed Kou’s criterion are summarized and compared.The numeric simulation and assessing methods of hot tearing,factors influencing hot tearing,and hot tearing susceptibility(HTS)of magnesium alloys are discussed.展开更多
由于镁合金凝固温度区间很长,所以容易产生热裂。作为新型的高强度变形镁合金,Mg-Zn-Y(ZW系)合金在半连续铸造过程中极易发生热裂。采用"CRC"(Constrained Rod Casting)铸造热裂试验及冷却曲线热分析方法研究了ZW系中ZW22、Z...由于镁合金凝固温度区间很长,所以容易产生热裂。作为新型的高强度变形镁合金,Mg-Zn-Y(ZW系)合金在半连续铸造过程中极易发生热裂。采用"CRC"(Constrained Rod Casting)铸造热裂试验及冷却曲线热分析方法研究了ZW系中ZW22、ZW42、ZW44、ZW26、ZW62合金的凝固路径,凝固最后阶段剩余液相分数以及锆细化等因素和其热裂倾向的关系。热裂纹位置因子、宽度因子等热裂敏感性因子的表征结果表明,合金的热裂倾向从大到小顺序为:无Zr的ZW62>ZW62>ZW22,ZW42和ZW44>ZW26合金。无Zr的ZW62合金比其他合金具有更大热裂倾向与几方面因素有关:具有最长的凝固温度区间;从枝晶干涉点到凝固终了温度间形成W相,阻碍枝晶间剩余液体的流动性,不利于枝晶间补缩;最后凝固阶段剩余液相最少,且该阶段固相分数随温度降低增长缓慢;粗大组织和发达的枝晶。展开更多
The effects of Cu and Zr additions, on the microstructure formation, precipitation and ingot cracking, in commercial 3003 Al alloys have been studied. The investigation was carried out by characterizing the grain stru...The effects of Cu and Zr additions, on the microstructure formation, precipitation and ingot cracking, in commercial 3003 Al alloys have been studied. The investigation was carried out by characterizing the grain structure in DC-cast rolling ingots, and studying the solidification microstructure of Bridgman directionally solidified samples. To better understand the influence of the different Cu and Zr contents on the phase precipitations, differential thermal analysis （DTA） experiments were performed. Results from the ingot microstructure analysis show that in commercial alloys with relatively high contents of Cu and Zr, no significant differences in measured grain sizes compared to conventional 3003 Al alloys could be found. However, only Zr containing alloys exhibited significantly larger grain sizes. Increased grain refiner and/or titanium additions could compensate for the negative effects on nucleation normally following Zr alloying. Different types of precipitates were observed. Based on DTA experiments, increased Cu and Zr contents resulted in the formation of Al2Cu phase, and increased solidification range. It was also found that increased Mn content favors an early precipitation of Al6（Mn,Fe） giving relatively coarse precipitates. It was concluded that the Cu alloying has a detrimental effect on hot tearing.展开更多
The hot tearing susceptibility of MgZn2.5YxZr0.5 （x=0.5, 1, 2, 4, 6） alloys was evaluated by thermodynamic calculations based on Clyne-Davies model. The microstructure and morphology of hot tearing regions of the al...The hot tearing susceptibility of MgZn2.5YxZr0.5 （x=0.5, 1, 2, 4, 6） alloys was evaluated by thermodynamic calculations based on Clyne-Davies model. The microstructure and morphology of hot tearing regions of the alloys were observed by X-ray diffraction and scanning electron microscopy. The solidification temperature and shrinkage stress during the solidification of MgZn2.5YxZr0.5 alloys in the“T”type hot tearing permanent-mold were acquired with the attached computer. The effect factors of hot tearing susceptibility of MgZn2.5YxZr0.5 alloys, such as the solidification temperature interval, the variation of solid fraction in vulnerable region, the residual liquid fraction in the final stage, the type of the second phase of the alloys were discussed based on the above calculation and observation. The results demonstrated that the hot tearing susceptibility in the investigated alloys was found as follows：MgZn2.5Y2Zr0.5＆gt;MgZn2.5Y0.5Zr0.5＆gt;MgZn2.5Y4Zr0.5＆gt;MgZn2.5Y6Zr0.5＆gt;MgZn2.5Y1Zr0.5. The highest hot tearing susceptibility of MgZn2.5Y2Zr0.5 alloy related to the following reasons： the largest freezing range, the biggest changing of the variation of solid fraction in vulnerable region, the least liquid film in the final stage of solidification, the formation of the second phase which worsens the liquid flow and interdendritic feeding after dendrite coherency.展开更多
Pouring and mold temperatures are two important parameters during casting magnesium components. The present study examined their influence on hot tearing susceptibility （HTS） of commercial AZ91D and newly developed ...Pouring and mold temperatures are two important parameters during casting magnesium components. The present study examined their influence on hot tearing susceptibility （HTS） of commercial AZ91D and newly developed Mg-3Nd-0.2Zn-Zr （mass fraction, %; NZ30K） magnesium alloys in gravity permanent mold casting condition. The results indicate that mold temperature shows much more significant influence on the HTS of both alloys than pouring temperature whose influence only can be distinguished at low mold temperature （341 K for AZ91D alloy and 423 K for NZ30K alloy）. Hot tearing susceptibility prediction model concerning feeding parameters, grain size and solidification range, is more suitable to estimate the HTS of different magnesium alloys than the model only concerning feeding parameters. In order to achieve better hot tearing resistance, the ranges of pouring and mold temperatures are suggested to be 961-991 K and≥641 K for AZ91D alloy, 1003-1033 K and≥623 K for NZ30K alloy, respectively.展开更多
The development of a modified 206 alloy whose composition was optimized to minimize hot tearing during semi-solid forming was reported. The effect of varying silicon, copper and iron contents was investigated using a ...The development of a modified 206 alloy whose composition was optimized to minimize hot tearing during semi-solid forming was reported. The effect of varying silicon, copper and iron contents was investigated using a design of experiment (DOE) approach. Semi-solid slurries were prepared using the SEED process and injected into a high pressure die casting press. The hot tearing sensitivity results were reported for different alloy variants. The microstructure evolution during the semi-solid preparation was presented along with actual die cast components. The effects of silicon, copper and iron on mechanical properties in the T7 condition were also analyzed. Beyond the benefit of reducing hot tearing, it is shown that the tensile and fatigue properties remain compatible with the automotive industry requirements.展开更多
基金the National Natural Science Foundation of China(Project 51531002,51474043)the Ministry of Science&Technology of China(2013DFA71070)+1 种基金the Ministry of Education of China(SRFDR 20130191110018)Chongqing Municipal Government(CSTC2013JCYJC60001,CEC project,Two River Scholar Project and The Chief Scientist Studio Project).
文摘Hot tearing is often a major casting defect in magnesium alloys and has a significant impact on the quality of their casting products.Hot tearing of magnesium alloys is a complex solidification phenomenon which is still not fully understood,it is of great importance to investigate the hot tearing behaviour of magnesium alloys.This review attempts to summarize the investigations on hot tearing of magnesium alloys over the past decades.The hot tearing criteria including recently developed Kou’s criterion are summarized and compared.The numeric simulation and assessing methods of hot tearing,factors influencing hot tearing,and hot tearing susceptibility(HTS)of magnesium alloys are discussed.
文摘由于镁合金凝固温度区间很长,所以容易产生热裂。作为新型的高强度变形镁合金,Mg-Zn-Y(ZW系)合金在半连续铸造过程中极易发生热裂。采用"CRC"(Constrained Rod Casting)铸造热裂试验及冷却曲线热分析方法研究了ZW系中ZW22、ZW42、ZW44、ZW26、ZW62合金的凝固路径,凝固最后阶段剩余液相分数以及锆细化等因素和其热裂倾向的关系。热裂纹位置因子、宽度因子等热裂敏感性因子的表征结果表明,合金的热裂倾向从大到小顺序为:无Zr的ZW62>ZW62>ZW22,ZW42和ZW44>ZW26合金。无Zr的ZW62合金比其他合金具有更大热裂倾向与几方面因素有关:具有最长的凝固温度区间;从枝晶干涉点到凝固终了温度间形成W相,阻碍枝晶间剩余液体的流动性,不利于枝晶间补缩;最后凝固阶段剩余液相最少,且该阶段固相分数随温度降低增长缓慢;粗大组织和发达的枝晶。
基金The Swedish KK-foundation, and the European Regional Development Fund supported this research financially
文摘The effects of Cu and Zr additions, on the microstructure formation, precipitation and ingot cracking, in commercial 3003 Al alloys have been studied. The investigation was carried out by characterizing the grain structure in DC-cast rolling ingots, and studying the solidification microstructure of Bridgman directionally solidified samples. To better understand the influence of the different Cu and Zr contents on the phase precipitations, differential thermal analysis （DTA） experiments were performed. Results from the ingot microstructure analysis show that in commercial alloys with relatively high contents of Cu and Zr, no significant differences in measured grain sizes compared to conventional 3003 Al alloys could be found. However, only Zr containing alloys exhibited significantly larger grain sizes. Increased grain refiner and/or titanium additions could compensate for the negative effects on nucleation normally following Zr alloying. Different types of precipitates were observed. Based on DTA experiments, increased Cu and Zr contents resulted in the formation of Al2Cu phase, and increased solidification range. It was also found that increased Mn content favors an early precipitation of Al6（Mn,Fe） giving relatively coarse precipitates. It was concluded that the Cu alloying has a detrimental effect on hot tearing.
基金Project (2011BAE22B01) supported by the National Key Technologies R&D Program,ChinaProject (2013CB632203) supported by the National Basic Research Program of China
文摘The hot tearing susceptibility of MgZn2.5YxZr0.5 （x=0.5, 1, 2, 4, 6） alloys was evaluated by thermodynamic calculations based on Clyne-Davies model. The microstructure and morphology of hot tearing regions of the alloys were observed by X-ray diffraction and scanning electron microscopy. The solidification temperature and shrinkage stress during the solidification of MgZn2.5YxZr0.5 alloys in the“T”type hot tearing permanent-mold were acquired with the attached computer. The effect factors of hot tearing susceptibility of MgZn2.5YxZr0.5 alloys, such as the solidification temperature interval, the variation of solid fraction in vulnerable region, the residual liquid fraction in the final stage, the type of the second phase of the alloys were discussed based on the above calculation and observation. The results demonstrated that the hot tearing susceptibility in the investigated alloys was found as follows：MgZn2.5Y2Zr0.5＆gt;MgZn2.5Y0.5Zr0.5＆gt;MgZn2.5Y4Zr0.5＆gt;MgZn2.5Y6Zr0.5＆gt;MgZn2.5Y1Zr0.5. The highest hot tearing susceptibility of MgZn2.5Y2Zr0.5 alloy related to the following reasons： the largest freezing range, the biggest changing of the variation of solid fraction in vulnerable region, the least liquid film in the final stage of solidification, the formation of the second phase which worsens the liquid flow and interdendritic feeding after dendrite coherency.
基金Project (2009AA033501) supported by the High-tech Research and Development Program of China
文摘Pouring and mold temperatures are two important parameters during casting magnesium components. The present study examined their influence on hot tearing susceptibility （HTS） of commercial AZ91D and newly developed Mg-3Nd-0.2Zn-Zr （mass fraction, %; NZ30K） magnesium alloys in gravity permanent mold casting condition. The results indicate that mold temperature shows much more significant influence on the HTS of both alloys than pouring temperature whose influence only can be distinguished at low mold temperature （341 K for AZ91D alloy and 423 K for NZ30K alloy）. Hot tearing susceptibility prediction model concerning feeding parameters, grain size and solidification range, is more suitable to estimate the HTS of different magnesium alloys than the model only concerning feeding parameters. In order to achieve better hot tearing resistance, the ranges of pouring and mold temperatures are suggested to be 961-991 K and≥641 K for AZ91D alloy, 1003-1033 K and≥623 K for NZ30K alloy, respectively.
文摘The development of a modified 206 alloy whose composition was optimized to minimize hot tearing during semi-solid forming was reported. The effect of varying silicon, copper and iron contents was investigated using a design of experiment (DOE) approach. Semi-solid slurries were prepared using the SEED process and injected into a high pressure die casting press. The hot tearing sensitivity results were reported for different alloy variants. The microstructure evolution during the semi-solid preparation was presented along with actual die cast components. The effects of silicon, copper and iron on mechanical properties in the T7 condition were also analyzed. Beyond the benefit of reducing hot tearing, it is shown that the tensile and fatigue properties remain compatible with the automotive industry requirements.
