针对AZ31镁合金作为镁电池负极时存在自腐蚀速率大、阳极极化、电位滞后等问题,寻找合适的缓蚀剂及其用量调配电解液以提高电池的放电性能。通过腐蚀浸泡试验表征了缓蚀剂Li_(2)CrO_(4)的缓蚀效果,然后通过极化曲线、电化学阻抗谱研究了...针对AZ31镁合金作为镁电池负极时存在自腐蚀速率大、阳极极化、电位滞后等问题,寻找合适的缓蚀剂及其用量调配电解液以提高电池的放电性能。通过腐蚀浸泡试验表征了缓蚀剂Li_(2)CrO_(4)的缓蚀效果,然后通过极化曲线、电化学阻抗谱研究了Mg(ClO_(4))_(2)溶液中Li_(2)CrO_(4)用量对AZ31镁合金电化学性能的影响,最后通过组装水系镁锰电池进行恒流放电作为应用端测试。结果表明:Li_(2)CrO_(4)能够使AZ31镁合金的腐蚀电位正移,最大正移量达到150 m V,在水系镁锰电池应用中能够提高镁电池的放电平台,当Li_(2)CrO_(4)质量分数为0.7%时放电平台提高0.15 V左右;当Li_(2)CrO_(4)质量分数为1.2%时,其能够显著改善AZ31镁合金在Mg(ClO_(4))_(2)溶液中的腐蚀,水系镁锰电池放电容量达最大,为196.9 m A·h,相对空白溶液,电池的放电容量提高约64%,工作电压高达1.39 V且放电曲线稳定。展开更多
OH radicals and O atoms are two of the most important reactive species of non-equilibrium atmospheric pressure plasma(NAPP),which plays an important role in applications such as plasma medicine.However,experimental st...OH radicals and O atoms are two of the most important reactive species of non-equilibrium atmospheric pressure plasma(NAPP),which plays an important role in applications such as plasma medicine.However,experimental studies on how the gas content affects the postdischarge temporal evolutions of OH and O in the noble gas ns-NAPP are very limited.In this work,the effect of the percentages of O_(2),N_(2),and H_(2)O on the amounts of OH and O productions and their post-discharge temporal behaviors in ns-NAPP is investigated by laser-induced fluorescence(LIF)method.The results show that the productions of OH and O increase and then decrease with the increase of O_(2)percentage.Both OH and O densities reach their maximum when about 0.8%O_(2)is added.Further increase of the O_(2)concentration results in a decrease of the initial densities of both OH and O,and leads to their faster decay.The increase of N_(2)percentage also results in the increase and then decrease of the OH and O densities,but the change is smaller.Furthermore,when the H_(2)O concentration is increased from 100 to 3000 ppm,the initial OH density increases slightly,but the OH density decays much faster,while the initial density of O decreases with the increase of the H_(2)O concentration.After analysis,it is found that OH and O are mainly produced through electron collisional dissociation.O(^(1)D)is critical for OH generation.O_(3)accelerates the consumption processes of OH and O at high O_(2)percentage.The addition of H_(2)O in the NAPP considerably enhances the electronegativity,while it decreases the overall plasma reactivity,accelerates the decay of OH,and reduces the O atom density.展开更多
The effects of yttrium(Y)and yttrium+calcium(Y+Ca)additions on the electrochemical properties and discharge performance of the as-extruded Mg−8Al−0.5Zn−0.2Mn(AZ80)anodes for Mg−air batteries were investigated.The resu...The effects of yttrium(Y)and yttrium+calcium(Y+Ca)additions on the electrochemical properties and discharge performance of the as-extruded Mg−8Al−0.5Zn−0.2Mn(AZ80)anodes for Mg−air batteries were investigated.The results show that the addition of 0.2 wt.%Y increased the corrosion resistance and discharge activity of AZ80 anode.This was attributed to the fine and sphericalβ-Mg_17)Al_(12) phases dispersing evenly in AZ80+0.2Y alloy,which suppressed the localized corrosion and severe“chunk effect”,and facilitated the rapid activation ofα-Mg.Combinative addition of 0.2 wt.%Y and 0.15 wt.%Ca generated grain refinement and a reduction of theβ-Mg_17)Al_(12) phase,resulting in a further enhancement in discharge voltage.However,the incorporation of Ca in Mg_17)Al_(12) and Al_(2)Y compounds compromised the corrosion resistance and anodic efficiency of AZ80+0.2Y+0.15Ca anode.Consequently,AZ80+0.2Y anode exhibited excellent overall discharge performance,with the peak discharge capacity and anodic efficiency of 1525 mA·h·g^(−1) and 67%at 80 mA/cm^(2),13%and 14%higher than those of AZ80 anode,respectively.展开更多
The self-corrosion, electrochemical and discharge behavior of commercial purity Al anode via Mn modification in Al-air battery was studied by the hydrogen evolution, weight loss, electrical conductivity, electrochemic...The self-corrosion, electrochemical and discharge behavior of commercial purity Al anode via Mn modification in Al-air battery was studied by the hydrogen evolution, weight loss, electrical conductivity, electrochemical and discharge tests. Results show that the synergetic effects of the dissolved Mn and Mn-modifying Al_(3)Fe intermetallic decrease the weight loss and inhibit the hydrogen evolution of commercial purity Al in Na OH solution when minor Mn is introduced. However, more Mn addition leads to the formation of Al_6Mn intermetallic,which has little effect on the weight loss, but accelerates the hydrogen evolution. Mn introduction plays a positive role in activating Al anodes, resulting in a decrease in the anodic polarization and an increase in the discharge voltage. Among all the commercial purity Al-x Mn anodes, 0.1 wt% Mn addition exhibits the best discharge efficiency for Al-air battery.展开更多
A series of extensive laboratory experiments were conducted to investigate the transport and mixing of instantaneous discharge of unsorted particle cloud in cross-flow. The following experimental results were obtained...A series of extensive laboratory experiments were conducted to investigate the transport and mixing of instantaneous discharge of unsorted particle cloud in cross-flow. The following experimental results were obtained： （1） the vertical frontal position and the longitudinal width of the particle cloud in the cross-flow is much larger than those in stagnant water, （2） the smaller cross-flow velocity will normally cause the larger non-dimensional frontal position for the same particle size range and initial volume, （3） the non-dimensional longitudinal width of the particle cloud in the cross-flow increases with the increase of cross-flow velocity. The empirical constants （α1, α3 and α2） and their variance range, which can be used to determine the relationships of non-dimensional vertical frontal position and time, longitudinal width and time, and vertical frontal position and longitudinal width were also obtained through the analysis of experimental data.展开更多
文摘目的分析出院计划在老年类风湿性关节炎(rheumatoid arthritis,RA)患者中的应用效果。方法便利抽样法选择2015年6月至2016年12月在某医院治疗的老年RA患者120例为研究对象。采用随机数字表法将其分为对照组和观察组,每组60例。对照组患者给予常规护理干预和健康宣教,观察组患者给予常规护理干预和出院计划干预。下一级社区医院对两组患者进行随访,比较2组患者遵医行为、不自主运动评定量表(abnormal involuntary movement scale,AIMS)评分及RA慢性期急性发作发生率和再次住院率的差异。结果出院后1周、1个月和6个月,观察组AIMS评分明显低于对照组,差异均有统计学意义(t=23.56,13,64和20.08,P<0.05)。在出院后1周、1个月和6个月,观察组遵医行为评分明显高于对照组,差异均有统计学意义(P<0.05);两组患者遵医行为评分随时间变化趋势不同(P<0.05);观察组RA患者慢性期急性发作发生率及再次住院率明显明显低于对照组,差异均有统计学意义(均P<0.05)。结论出院计划应用于类风湿性关节炎患者的康复中,能够改善患者的遵医行为,降低急性发作发生率,提高患者的生活质量,值得进一步推广应用。
文摘针对AZ31镁合金作为镁电池负极时存在自腐蚀速率大、阳极极化、电位滞后等问题,寻找合适的缓蚀剂及其用量调配电解液以提高电池的放电性能。通过腐蚀浸泡试验表征了缓蚀剂Li_(2)CrO_(4)的缓蚀效果,然后通过极化曲线、电化学阻抗谱研究了Mg(ClO_(4))_(2)溶液中Li_(2)CrO_(4)用量对AZ31镁合金电化学性能的影响,最后通过组装水系镁锰电池进行恒流放电作为应用端测试。结果表明:Li_(2)CrO_(4)能够使AZ31镁合金的腐蚀电位正移,最大正移量达到150 m V,在水系镁锰电池应用中能够提高镁电池的放电平台,当Li_(2)CrO_(4)质量分数为0.7%时放电平台提高0.15 V左右;当Li_(2)CrO_(4)质量分数为1.2%时,其能够显著改善AZ31镁合金在Mg(ClO_(4))_(2)溶液中的腐蚀,水系镁锰电池放电容量达最大,为196.9 m A·h,相对空白溶液,电池的放电容量提高约64%,工作电压高达1.39 V且放电曲线稳定。
基金supported by National Natural Science Foundation of China(Nos.52130701 and 51977096)the National Key Research and Development Program of China(No.2021YFE0114700)。
文摘OH radicals and O atoms are two of the most important reactive species of non-equilibrium atmospheric pressure plasma(NAPP),which plays an important role in applications such as plasma medicine.However,experimental studies on how the gas content affects the postdischarge temporal evolutions of OH and O in the noble gas ns-NAPP are very limited.In this work,the effect of the percentages of O_(2),N_(2),and H_(2)O on the amounts of OH and O productions and their post-discharge temporal behaviors in ns-NAPP is investigated by laser-induced fluorescence(LIF)method.The results show that the productions of OH and O increase and then decrease with the increase of O_(2)percentage.Both OH and O densities reach their maximum when about 0.8%O_(2)is added.Further increase of the O_(2)concentration results in a decrease of the initial densities of both OH and O,and leads to their faster decay.The increase of N_(2)percentage also results in the increase and then decrease of the OH and O densities,but the change is smaller.Furthermore,when the H_(2)O concentration is increased from 100 to 3000 ppm,the initial OH density increases slightly,but the OH density decays much faster,while the initial density of O decreases with the increase of the H_(2)O concentration.After analysis,it is found that OH and O are mainly produced through electron collisional dissociation.O(^(1)D)is critical for OH generation.O_(3)accelerates the consumption processes of OH and O at high O_(2)percentage.The addition of H_(2)O in the NAPP considerably enhances the electronegativity,while it decreases the overall plasma reactivity,accelerates the decay of OH,and reduces the O atom density.
基金financial supports from the Key Development Project of Sichuan Province,China (No.2017GZ0399)the National Natural Science Foundation of China (No.52061040)the Open Projects of the Key Laboratory of Advanced Technologies of Materials,Ministry of Education,Southwest Jiaotong University,China (No.KLATM202003)。
文摘The effects of yttrium(Y)and yttrium+calcium(Y+Ca)additions on the electrochemical properties and discharge performance of the as-extruded Mg−8Al−0.5Zn−0.2Mn(AZ80)anodes for Mg−air batteries were investigated.The results show that the addition of 0.2 wt.%Y increased the corrosion resistance and discharge activity of AZ80 anode.This was attributed to the fine and sphericalβ-Mg_17)Al_(12) phases dispersing evenly in AZ80+0.2Y alloy,which suppressed the localized corrosion and severe“chunk effect”,and facilitated the rapid activation ofα-Mg.Combinative addition of 0.2 wt.%Y and 0.15 wt.%Ca generated grain refinement and a reduction of theβ-Mg_17)Al_(12) phase,resulting in a further enhancement in discharge voltage.However,the incorporation of Ca in Mg_17)Al_(12) and Al_(2)Y compounds compromised the corrosion resistance and anodic efficiency of AZ80+0.2Y+0.15Ca anode.Consequently,AZ80+0.2Y anode exhibited excellent overall discharge performance,with the peak discharge capacity and anodic efficiency of 1525 mA·h·g^(−1) and 67%at 80 mA/cm^(2),13%and 14%higher than those of AZ80 anode,respectively.
基金financially supported by Anhui Provincial Natural Science Foundation (No. 1808085ME123)the Projects of International Cooperation and Exchanges in Anhui Provincial Key Project of Research and Development Plan (No.1804b06020363)the Priority Funding Scheme for Innovative Projects for Overseas Chinese Students in Anhui Province。
文摘The self-corrosion, electrochemical and discharge behavior of commercial purity Al anode via Mn modification in Al-air battery was studied by the hydrogen evolution, weight loss, electrical conductivity, electrochemical and discharge tests. Results show that the synergetic effects of the dissolved Mn and Mn-modifying Al_(3)Fe intermetallic decrease the weight loss and inhibit the hydrogen evolution of commercial purity Al in Na OH solution when minor Mn is introduced. However, more Mn addition leads to the formation of Al_6Mn intermetallic,which has little effect on the weight loss, but accelerates the hydrogen evolution. Mn introduction plays a positive role in activating Al anodes, resulting in a decrease in the anodic polarization and an increase in the discharge voltage. Among all the commercial purity Al-x Mn anodes, 0.1 wt% Mn addition exhibits the best discharge efficiency for Al-air battery.
基金the Key Subject of Shanghai Education Committee (Grant No. J50702).
文摘A series of extensive laboratory experiments were conducted to investigate the transport and mixing of instantaneous discharge of unsorted particle cloud in cross-flow. The following experimental results were obtained： （1） the vertical frontal position and the longitudinal width of the particle cloud in the cross-flow is much larger than those in stagnant water, （2） the smaller cross-flow velocity will normally cause the larger non-dimensional frontal position for the same particle size range and initial volume, （3） the non-dimensional longitudinal width of the particle cloud in the cross-flow increases with the increase of cross-flow velocity. The empirical constants （α1, α3 and α2） and their variance range, which can be used to determine the relationships of non-dimensional vertical frontal position and time, longitudinal width and time, and vertical frontal position and longitudinal width were also obtained through the analysis of experimental data.
