Based on the investigation of mid-span local boundary layer suction and positive bowed cascade, a coupled local tailored boundary layer suction and positive bowed blade method is developed to improve the performance o...Based on the investigation of mid-span local boundary layer suction and positive bowed cascade, a coupled local tailored boundary layer suction and positive bowed blade method is developed to improve the performance of a highly loaded diffusion cascade with less suction slot. The effectiveness of the coupled method under different inlet boundary layers is also investigated.Results show that mid-span local boundary layer suction can effectively remove trailing edge separation, but deteriorate the flow fields near the endwall. The positive bowed cascade is beneficial for reducing open corner separation, but is detrimental to mid-span flow fields. The coupled method can further improve the performance and flow field of the cascade. The mid-span trailing edge separation and open corner separation are eliminated. Compared with linear cascade with suction, the coupled method reduces overall loss of the cascade by 31.4% at most. The mid-span loss of the cascade decreases as the suction coefficient increases, but increases as bow angle increases. The endwall loss increases as the suction coefficient increases. By contrast, the endwall loss decreases significantly as the bow angle increases. The endwall loss of coupled controlled cascade is higher than that of bowed cascade with the same bow angle because of the spanwise inverse ‘‘C＂ shaped static pressure distribution. Under different inlet boundary layer conditions, the coupled method can also improve the cascade effectively.展开更多
Corner stall receives noticeable attention in the aeroengine field as an important phenomenon in highly-load compressors.Non-uniform leading-edge tubercles,as an effective method to delay stall,are introduced into the...Corner stall receives noticeable attention in the aeroengine field as an important phenomenon in highly-load compressors.Non-uniform leading-edge tubercles,as an effective method to delay stall,are introduced into the compressor.In this paper,the shape of leading-edge tubercles was controlled by a third-order Fourier function.To judge corner stall,a more precise stall indicator for compressor cascade with flow control methods was defined.Besides,the total kinetic energy of the secondary flow at large incidence was adopted as a parameter for stall evaluation to save computing resources.The results of multiobjective optimization reveal that the loss coefficient exhibited negligible variation at design incidence,while the total kinetic energy of secondary flow showed a significant reduction at large incidence,resulting in a substantial increase in stall incidence.In the optimal profiling cases,the stall incidencewas delayed from 7.9°to 11.6°.The major purpose of the research is to provide proper design guidelines for nonuniformleading-edge tubercles and uncover the flow controlmechanisms of leading-edge profiling.Hence,the geometric features that meet different optimization objectives were extracted through geometric analysis near the Pareto Front and through Self-OrganizingMap(SOM)dataminingmethods in the optimization database.Besides,flow field analysis reveals the flow control mechanism of leading-edge tubercles.The convex-concave-convex structure at the 0%-70%blade height region can form two branches of leading-edge vortex pairs that are opposite in the rotation direction to the passage vortex.The two branches of leading-edge vortex pairs mixed with the leading-edge separation vortex to form two stronger mixed vortices,which can effectively suppress the development of passage vortex and delay stall incidence.展开更多
It is well known that riblet applied on compressor blades is a promising flow control technique. However, detailed investigation of its effects on the flow field of turbomachinery is rare in existing literatures. This...It is well known that riblet applied on compressor blades is a promising flow control technique. However, detailed investigation of its effects on the flow field of turbomachinery is rare in existing literatures. This paper presents a detailed experimental investigation of effects of distributed riblet on the flow field of an axial compressor iso- lated-rotor stage. The research was performed in a large-scale facility respectively with two configurations, in- eluding grooved hub, and grooved surface on both hub and partial suction surface. The riblet film is rectangle grooved type with a height of 0.1 ram. The flow field at 10% chord downstream from the cascade trailing edge was measured using a mini five-hole pressure probe and a total pressure probe. The testing was conducted at sev- eral operational points under two reduced rotational speeds. Stagnation pressure loss in rotational frame was cal- culated and compared with the control test in which a smooth film was applied to the corresponding position. Results show that with the grooved hub configuration at the design operation point of the lower rotational speed, the riblet film provides an obvious improvement of a 48% reduction of total pressure loss in rotational frame. Also, a distinct weaken hub comer vortex was identified. In the meantime, there exists a deviation of flow angle about 5 degrees at 20%-80% span which previously was not considered to be the affected region.展开更多
The vortex pump has increasingly become an important alternative or supplement to the centrifugal pump, the positive displacement pump and the diffusion pump due to its capacity of developing a high head at a small fl...The vortex pump has increasingly become an important alternative or supplement to the centrifugal pump, the positive displacement pump and the diffusion pump due to its capacity of developing a high head at a small flow rate within a single stage. However, the vortex pumps with various blade shapes such as the twisted blades or the 3-D blades are not well studied. In this paper, some new concepts of the 2-D and 3-D corner blades are introduced for the design of the vortex pumps. The mechanism behind the effect of the corner blade shapes on the pump hydraulic performance is numerically investigated and elucidated in terms of the internal vortex structures. The results show that both 2-D and 3-D forward corner blades can induce stronger well-organized longitudinal vortices as well as smaller axial and radial vortices within the impeller blade passage, which benefit a higher pump head and a higher efficiency in comparison with the traditional radial straight blade. This study provides useful guidelines for the design of advanced vortex pumps.展开更多
Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investi...Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investigated the influence on details of the flow fields,especially vortexes in compressors. CFD method is validated with experi?mental data firstly. Three single?slot and one double?slot endwall boundary layer suction schemes are designed and investigated. In addition to the investigation of aerodynamic performance of the cascades with and without suction,variations in corner open separation,passage vortex,and concentration shedding vortex,which are rarely seen for the flow controlled blades in published literatures,are analyzed. Then,flow models,which are the ultimate aim,of both baseline and aspirated cascades are established. Results show that single?slot endwall suction scheme adjacent to the suction surface can e ectively remove the corner open separation. With suction mass flow rate of 0.85%,the overall loss coe cient and endwall loss coe cient of the cascade are reduced by 25.2% and 48.6%,respectively. Besides,this scheme increases the static pressure rise coe cient of the cascade by 3.2% and the flow turning angle of up to 3.3° at 90% span. The concentration shedding vortex decreases,whereas the passage vortex increases. For single?slot suction schemes near the middle pitchwise of the passage,the concentration shedding vortex increases and the passage vortex is divided into two smaller passage vortexes,which converge into a single?passage vortex near the trailing edge section of the cascade. For the double?slot suction scheme,triple?passage vortexes are presented in the blade passage. Some new vortex structures are discovered,and the novel flow models of aspirated compressor cascade are proposed,which are important to improve the design of multi?stage aspirated compressors.展开更多
This paper presents the effect of wind tunnel sidewalls on the wind turbine airfoils with experimental and numerical methods.The test is carried out in a low-speed wind tunnel at Re=2.62×10^(5).Pressures acting o...This paper presents the effect of wind tunnel sidewalls on the wind turbine airfoils with experimental and numerical methods.The test is carried out in a low-speed wind tunnel at Re=2.62×10^(5).Pressures acting on the airfoil surface are measured by a multiport pressure device.And,the oil flow visualization technique is used to investigate the flow field characteristics of the airfoil surface.Then,a numerical simulation was conducted with the measurement results.As a result,it is clarified the flow structures on the airfoil surface depend strongly on the angles of attack and the sidewalls.At small angles of attack,the three-dimensional separation caused by the interaction between the sidewall boundary layer and the airfoil boundary layer is very small,and only appears near the junction of the airfoil model and the sidewall.This corner separation becomes large with the increase of the angle of attack.At the middle part of the testing model,the boundary layer flow evolves into three-dimensional separation,i.e.,stall cell,when the separation develops to an appreciate extent.The stall phenomenon will further spread from the center line to sidewalls with the increase of the angle of attack;and then,its development will be limited by the sidewall boundary layer separation.Comparably,the simulation shows that the sidewall make the pressure coefficient Cpdecrease,and proper boundary condition can maintain two-dimensional flow at large angles of attack by eliminating the influence of corner vortices.展开更多
It has been recently shown that Sub Boundary layer Vortex Generator(SBVG,abbreviated as VG hereafter)can suppress the Cross-Flow(CF),and therefore,can eliminate corner separation and increase aerodynamic loading when ...It has been recently shown that Sub Boundary layer Vortex Generator(SBVG,abbreviated as VG hereafter)can suppress the Cross-Flow(CF),and therefore,can eliminate corner separation and increase aerodynamic loading when installed on the end wall inside middle-load compressor passages.However,when VGs are applied in high-load compressors,it is difficult to achieve ideal results.This is because the definition of the VG attack angle in the presence of CF in existing research is confusing,and the stronger CF in high-load compressors worsens the problem and results in an improper design and optimization range of VG attack angle.Therefore,this paper clarifies the definition of the VG attack angle in the presence of CF and reveals the CF controlling mechanism of VG on a flat plate.The differences in the flow phenomena around a VG both with and without CF are also studied.The numerical results show that a larger height or attack angle of the VG generates a greater CF suppression effect.However,the cross velocity increases when surmounting the primary vortex induced by the VG,except that this enhanced CF is less conspicuous for larger VG heights.Compared to the cases without CF,the VG suffers an additional loss because of the stronger separation and primary vortex loss caused by the CF.展开更多
基金supported by China Postdoctoral Science Foundationa key project of the National Natural Science Foundation of China (No. 51236006)
文摘Based on the investigation of mid-span local boundary layer suction and positive bowed cascade, a coupled local tailored boundary layer suction and positive bowed blade method is developed to improve the performance of a highly loaded diffusion cascade with less suction slot. The effectiveness of the coupled method under different inlet boundary layers is also investigated.Results show that mid-span local boundary layer suction can effectively remove trailing edge separation, but deteriorate the flow fields near the endwall. The positive bowed cascade is beneficial for reducing open corner separation, but is detrimental to mid-span flow fields. The coupled method can further improve the performance and flow field of the cascade. The mid-span trailing edge separation and open corner separation are eliminated. Compared with linear cascade with suction, the coupled method reduces overall loss of the cascade by 31.4% at most. The mid-span loss of the cascade decreases as the suction coefficient increases, but increases as bow angle increases. The endwall loss increases as the suction coefficient increases. By contrast, the endwall loss decreases significantly as the bow angle increases. The endwall loss of coupled controlled cascade is higher than that of bowed cascade with the same bow angle because of the spanwise inverse ‘‘C＂ shaped static pressure distribution. Under different inlet boundary layer conditions, the coupled method can also improve the cascade effectively.
基金support by the National Natural Science Foundation of China(No.52076179).
文摘Corner stall receives noticeable attention in the aeroengine field as an important phenomenon in highly-load compressors.Non-uniform leading-edge tubercles,as an effective method to delay stall,are introduced into the compressor.In this paper,the shape of leading-edge tubercles was controlled by a third-order Fourier function.To judge corner stall,a more precise stall indicator for compressor cascade with flow control methods was defined.Besides,the total kinetic energy of the secondary flow at large incidence was adopted as a parameter for stall evaluation to save computing resources.The results of multiobjective optimization reveal that the loss coefficient exhibited negligible variation at design incidence,while the total kinetic energy of secondary flow showed a significant reduction at large incidence,resulting in a substantial increase in stall incidence.In the optimal profiling cases,the stall incidencewas delayed from 7.9°to 11.6°.The major purpose of the research is to provide proper design guidelines for nonuniformleading-edge tubercles and uncover the flow controlmechanisms of leading-edge profiling.Hence,the geometric features that meet different optimization objectives were extracted through geometric analysis near the Pareto Front and through Self-OrganizingMap(SOM)dataminingmethods in the optimization database.Besides,flow field analysis reveals the flow control mechanism of leading-edge tubercles.The convex-concave-convex structure at the 0%-70%blade height region can form two branches of leading-edge vortex pairs that are opposite in the rotation direction to the passage vortex.The two branches of leading-edge vortex pairs mixed with the leading-edge separation vortex to form two stronger mixed vortices,which can effectively suppress the development of passage vortex and delay stall incidence.
基金funded by the National Natural Science Foundation of China,Grant No.51161130525 and 51136003supported by the 111 Project,No.B07009
文摘It is well known that riblet applied on compressor blades is a promising flow control technique. However, detailed investigation of its effects on the flow field of turbomachinery is rare in existing literatures. This paper presents a detailed experimental investigation of effects of distributed riblet on the flow field of an axial compressor iso- lated-rotor stage. The research was performed in a large-scale facility respectively with two configurations, in- eluding grooved hub, and grooved surface on both hub and partial suction surface. The riblet film is rectangle grooved type with a height of 0.1 ram. The flow field at 10% chord downstream from the cascade trailing edge was measured using a mini five-hole pressure probe and a total pressure probe. The testing was conducted at sev- eral operational points under two reduced rotational speeds. Stagnation pressure loss in rotational frame was cal- culated and compared with the control test in which a smooth film was applied to the corresponding position. Results show that with the grooved hub configuration at the design operation point of the lower rotational speed, the riblet film provides an obvious improvement of a 48% reduction of total pressure loss in rotational frame. Also, a distinct weaken hub comer vortex was identified. In the meantime, there exists a deviation of flow angle about 5 degrees at 20%-80% span which previously was not considered to be the affected region.
基金Project supported by the National Key Research and Development Project of China(Grant No.2016YFB0200903)the National Natural Science Foundation of China(Grant No.51776154)
文摘The vortex pump has increasingly become an important alternative or supplement to the centrifugal pump, the positive displacement pump and the diffusion pump due to its capacity of developing a high head at a small flow rate within a single stage. However, the vortex pumps with various blade shapes such as the twisted blades or the 3-D blades are not well studied. In this paper, some new concepts of the 2-D and 3-D corner blades are introduced for the design of the vortex pumps. The mechanism behind the effect of the corner blade shapes on the pump hydraulic performance is numerically investigated and elucidated in terms of the internal vortex structures. The results show that both 2-D and 3-D forward corner blades can induce stronger well-organized longitudinal vortices as well as smaller axial and radial vortices within the impeller blade passage, which benefit a higher pump head and a higher efficiency in comparison with the traditional radial straight blade. This study provides useful guidelines for the design of advanced vortex pumps.
基金Supported by China Postdoctoral Science Foundation(Grant No.2016M600015)National Natural Science Foundation of China(Grant Nos.51741601,51236006)
文摘Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investigated the influence on details of the flow fields,especially vortexes in compressors. CFD method is validated with experi?mental data firstly. Three single?slot and one double?slot endwall boundary layer suction schemes are designed and investigated. In addition to the investigation of aerodynamic performance of the cascades with and without suction,variations in corner open separation,passage vortex,and concentration shedding vortex,which are rarely seen for the flow controlled blades in published literatures,are analyzed. Then,flow models,which are the ultimate aim,of both baseline and aspirated cascades are established. Results show that single?slot endwall suction scheme adjacent to the suction surface can e ectively remove the corner open separation. With suction mass flow rate of 0.85%,the overall loss coe cient and endwall loss coe cient of the cascade are reduced by 25.2% and 48.6%,respectively. Besides,this scheme increases the static pressure rise coe cient of the cascade by 3.2% and the flow turning angle of up to 3.3° at 90% span. The concentration shedding vortex decreases,whereas the passage vortex increases. For single?slot suction schemes near the middle pitchwise of the passage,the concentration shedding vortex increases and the passage vortex is divided into two smaller passage vortexes,which converge into a single?passage vortex near the trailing edge section of the cascade. For the double?slot suction scheme,triple?passage vortexes are presented in the blade passage. Some new vortex structures are discovered,and the novel flow models of aspirated compressor cascade are proposed,which are important to improve the design of multi?stage aspirated compressors.
基金funded by the National Natural Science Foundation of China(No.51776204)。
文摘This paper presents the effect of wind tunnel sidewalls on the wind turbine airfoils with experimental and numerical methods.The test is carried out in a low-speed wind tunnel at Re=2.62×10^(5).Pressures acting on the airfoil surface are measured by a multiport pressure device.And,the oil flow visualization technique is used to investigate the flow field characteristics of the airfoil surface.Then,a numerical simulation was conducted with the measurement results.As a result,it is clarified the flow structures on the airfoil surface depend strongly on the angles of attack and the sidewalls.At small angles of attack,the three-dimensional separation caused by the interaction between the sidewall boundary layer and the airfoil boundary layer is very small,and only appears near the junction of the airfoil model and the sidewall.This corner separation becomes large with the increase of the angle of attack.At the middle part of the testing model,the boundary layer flow evolves into three-dimensional separation,i.e.,stall cell,when the separation develops to an appreciate extent.The stall phenomenon will further spread from the center line to sidewalls with the increase of the angle of attack;and then,its development will be limited by the sidewall boundary layer separation.Comparably,the simulation shows that the sidewall make the pressure coefficient Cpdecrease,and proper boundary condition can maintain two-dimensional flow at large angles of attack by eliminating the influence of corner vortices.
基金sponsored by the National Natural Science Foundation of China(Nos.51976010,52006011)National Major Science and Technology Projects of China(Nos.2017Ⅱ-0006-0020,2017-Ⅱ-0001-0013,J2019-Ⅱ-0003-0023)Beijing Institute of Technology Research Fund Program for Young Scholars,China。
文摘It has been recently shown that Sub Boundary layer Vortex Generator(SBVG,abbreviated as VG hereafter)can suppress the Cross-Flow(CF),and therefore,can eliminate corner separation and increase aerodynamic loading when installed on the end wall inside middle-load compressor passages.However,when VGs are applied in high-load compressors,it is difficult to achieve ideal results.This is because the definition of the VG attack angle in the presence of CF in existing research is confusing,and the stronger CF in high-load compressors worsens the problem and results in an improper design and optimization range of VG attack angle.Therefore,this paper clarifies the definition of the VG attack angle in the presence of CF and reveals the CF controlling mechanism of VG on a flat plate.The differences in the flow phenomena around a VG both with and without CF are also studied.The numerical results show that a larger height or attack angle of the VG generates a greater CF suppression effect.However,the cross velocity increases when surmounting the primary vortex induced by the VG,except that this enhanced CF is less conspicuous for larger VG heights.Compared to the cases without CF,the VG suffers an additional loss because of the stronger separation and primary vortex loss caused by the CF.
