Electro-oxidation of Ce （ Ⅲ ） to Ce （ Ⅳ ） in parallel plate flow type electrolyzer divided with cation exchange membrane was carried out in nitric acid media at carbon felt anode under galvanostatic conditions. ...Electro-oxidation of Ce （ Ⅲ ） to Ce （ Ⅳ ） in parallel plate flow type electrolyzer divided with cation exchange membrane was carried out in nitric acid media at carbon felt anode under galvanostatic conditions. Carbon felt was used as an anode for its high specific surface area and high oxygen evolution overpotential. Pt coated Ti plates were used as cathode and anode current feeder. The oxidation of 1 mol· L^-1 Ce（ Ⅲ ） solution in 2 mol· L^- 1 HNO3 was proceeding with a high current efficiency （92%） until about 80% of Ce（ Ⅲ ） was oxidized. Then, oxygen evolution, accompanied by terminal voltage jump, took place, lowering current efficiency. Ce（ Ⅲ ） was oxidized up to 90% with current efficiency of 62%. In this mode, strong carbon felt anode oxidation was observed. The wear out of carbon felt was 46% in six consequent runs （6 h of operation）. After each run, carbon felt surface had to be renewed with slightly alkaline solution to remove carbon oxidation products and ensure regular operational conditions. When anode surface was blocked, oxygen evolution took place from the beginning of electrolysis due to higher actual current density. The wear out of carbon felt anode could be minimized by means of oxygen evolution prevention. In the case when electrolysis had been stopped before oxygen evolution started （at Ce（ Ⅳ ） conversion of about 80% ）, the wear out of anode was less than 2% during 6 consequent runs （4 h of operation）.展开更多
A monolithic series of Cu-Mn-Ce oxides supported on cordierites with different Cu/Mn/Ce molar ratios were prepared by the in-situ sol-gel method without any binder. The catalysts were characterized by scanning electro...A monolithic series of Cu-Mn-Ce oxides supported on cordierites with different Cu/Mn/Ce molar ratios were prepared by the in-situ sol-gel method without any binder. The catalysts were characterized by scanning electron microscopy （SEM）, energy dispersive spectrometer （EDS）, X-ray diffraction （XRD）, and Brunauer-Emmett-Teller method （BET） and examined in the catalytic combustion of volatile organic compounds （VOCs）. The results showed that the well-dispersed nanometer particles of mixed oxides adhered firmly to the cordierite surface. Cu0.15Mn0.3Ce55/cordierite was identified as the most active catalyst. Compared with commercial Pd/Al2O3, Cu0.15Mn0.3Ce55/cordierite showed higher activities for the combustion of various types of VOCs, especially for oxy-derivative compounds which could be lighted off below 200 ℃.展开更多
Samples of cerium-manganese oxides supported on modified glass-fiber with different Ce/Mn molar ratios （Ce-Mn/GF） were prepared by an impregnation method and tested for low-temperature （80 180 ℃） selective cataly...Samples of cerium-manganese oxides supported on modified glass-fiber with different Ce/Mn molar ratios （Ce-Mn/GF） were prepared by an impregnation method and tested for low-temperature （80 180 ℃） selective catalytic reduction （SCR） of NO with ammonia. This brand-new technology could remove NO and particles matter from coal-fired flue gas. The surface properties of the catalysts were examined by means of Bmnauer-Emmett-Teller （BET）, X-ray photoelectron spectroscopy （XPS）, X-ray diffraction （XRD）, and scanning electron microscopy （SEM）. The experimental results showed that the catalyst with a Ce/Mn molar ratio of 0.2 obtained high activity of 87.4% NO conversion at 150 ℃ under a high space velocity of 50000 h1. Deactivation poisoned by SO2 still occurred, but the Ce-Mn/GF（0.2） catalyst performed desirable tolerance to SO2 with decreasing 50% in 40 min and then maintaining at about 30% NO conversion. Characterization results indicated that the excellent low-temperature catalytic activity was related to the high specific surface area, pore structure, and amorphous phase.展开更多
文摘Electro-oxidation of Ce （ Ⅲ ） to Ce （ Ⅳ ） in parallel plate flow type electrolyzer divided with cation exchange membrane was carried out in nitric acid media at carbon felt anode under galvanostatic conditions. Carbon felt was used as an anode for its high specific surface area and high oxygen evolution overpotential. Pt coated Ti plates were used as cathode and anode current feeder. The oxidation of 1 mol· L^-1 Ce（ Ⅲ ） solution in 2 mol· L^- 1 HNO3 was proceeding with a high current efficiency （92%） until about 80% of Ce（ Ⅲ ） was oxidized. Then, oxygen evolution, accompanied by terminal voltage jump, took place, lowering current efficiency. Ce（ Ⅲ ） was oxidized up to 90% with current efficiency of 62%. In this mode, strong carbon felt anode oxidation was observed. The wear out of carbon felt was 46% in six consequent runs （6 h of operation）. After each run, carbon felt surface had to be renewed with slightly alkaline solution to remove carbon oxidation products and ensure regular operational conditions. When anode surface was blocked, oxygen evolution took place from the beginning of electrolysis due to higher actual current density. The wear out of carbon felt anode could be minimized by means of oxygen evolution prevention. In the case when electrolysis had been stopped before oxygen evolution started （at Ce（ Ⅳ ） conversion of about 80% ）, the wear out of anode was less than 2% during 6 consequent runs （4 h of operation）.
基金Project supported by National Natural Science Foundation of China (21107096)Zhejiang Provincial Natural Science Foundation (Y5090202)
文摘A monolithic series of Cu-Mn-Ce oxides supported on cordierites with different Cu/Mn/Ce molar ratios were prepared by the in-situ sol-gel method without any binder. The catalysts were characterized by scanning electron microscopy （SEM）, energy dispersive spectrometer （EDS）, X-ray diffraction （XRD）, and Brunauer-Emmett-Teller method （BET） and examined in the catalytic combustion of volatile organic compounds （VOCs）. The results showed that the well-dispersed nanometer particles of mixed oxides adhered firmly to the cordierite surface. Cu0.15Mn0.3Ce55/cordierite was identified as the most active catalyst. Compared with commercial Pd/Al2O3, Cu0.15Mn0.3Ce55/cordierite showed higher activities for the combustion of various types of VOCs, especially for oxy-derivative compounds which could be lighted off below 200 ℃.
基金Project supported by the National High Technology Research and Development Program of China(863 Program)(2008AA05Z305)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministry(201109)+2 种基金the Master Dissertation Innovation Funded Projects(EG2013015)the Fundamental Research Funds for the Central Universities Special Fund Project(11D11315)Program of Shanghai Subject Chief Scientist(14XD1424700)
文摘Samples of cerium-manganese oxides supported on modified glass-fiber with different Ce/Mn molar ratios （Ce-Mn/GF） were prepared by an impregnation method and tested for low-temperature （80 180 ℃） selective catalytic reduction （SCR） of NO with ammonia. This brand-new technology could remove NO and particles matter from coal-fired flue gas. The surface properties of the catalysts were examined by means of Bmnauer-Emmett-Teller （BET）, X-ray photoelectron spectroscopy （XPS）, X-ray diffraction （XRD）, and scanning electron microscopy （SEM）. The experimental results showed that the catalyst with a Ce/Mn molar ratio of 0.2 obtained high activity of 87.4% NO conversion at 150 ℃ under a high space velocity of 50000 h1. Deactivation poisoned by SO2 still occurred, but the Ce-Mn/GF（0.2） catalyst performed desirable tolerance to SO2 with decreasing 50% in 40 min and then maintaining at about 30% NO conversion. Characterization results indicated that the excellent low-temperature catalytic activity was related to the high specific surface area, pore structure, and amorphous phase.
