A 3D bounding surface model is established for rockfill materials,which can be applied to appropriately predict the deformation and the stabilization of rockfill dams.Firstly,an associated plastic flow rule for rockfi...A 3D bounding surface model is established for rockfill materials,which can be applied to appropriately predict the deformation and the stabilization of rockfill dams.Firstly,an associated plastic flow rule for rockfill materials is investigated based on the elaborate data from the large-style triaxial compression tests and the true triaxial tests.Secondly,the constitutive equations of the 3D bounding surface model are established by several steps.These steps include the bounding surface incorporating the general nonlinear strength criterion,stress-dilatancy equations,the evolution of the bounding surface and the bounding surface plasticity.Finally,the 3D bounding surface model is used to predict the mechanical behaviors of rockfill materials from the large-style triaxial compression tests and the true triaxial tests.Consequently,the proposed 3D bounding surface model can well capture such behaviors of rockfill materials as the strain hardening,the post-peak strain softening,and the volumetric strain contraction and expansion in both two-and three-dimensional stress spaces.展开更多
Particle size distribution significantly influences the mechanical response of the ballast under low confining pressure.However,particle breakage usually occurs and unfavorably degrades the particle size distribution ...Particle size distribution significantly influences the mechanical response of the ballast under low confining pressure.However,particle breakage usually occurs and unfavorably degrades the particle size distribution of the ballast when sufficient load is applied.To model the triaxial stress-strain behavior and its associated evolution of particle size distribution of the ballast,a specific bounding surface model is proposed.The proposed model is based on the traditional bounding surface plasticity and a modified particle breakage index,which correlates the initial gradation and the ultimate gradation together with the current gradation.Simulation of the experimental results from the triaxial compression tests shows that the proposed model can predict the strain softening and volumetric expansion of the ballast under relatively lower confining pressure.It is also able to simulate the strain hardening and volumetric compression of the ballast under relatively higher confining pressure.Most importantly,the proposed approach was observed to have a great potential in predicting the evolution of the particle size distribution of the ballast.展开更多
A bounding surface model incorporating a unified nonlinear strength criterion is proposed.The proposed bounding surface model contains 9 model parameters,which can be determined from the conventional triaxial tests.Th...A bounding surface model incorporating a unified nonlinear strength criterion is proposed.The proposed bounding surface model contains 9 model parameters,which can be determined from the conventional triaxial tests.The bounding surface model can reproduce such behaviours as the strain hardening,the post-peak strain softening,and the volumetric strain contraction and expansion.Based on the comparisons between the predictions and the test results,the proposed strength criterion and model can well reproduce the experimental results of the strength and stress-strain behaviours of rockfill material in three-dimensional stress space.The strength behaviour of rockfill material is summarized as:(a) the failure stress ratio decreases with the initial confining pressure on the meridian plane;(b) the failure deviatoric stress decreases with the Lode angle from 0o to 60o on the deviatoric plane.The stress ratio decreases with increasing one of such factors as the initial void ratio,the intermediate principal stress ratio and the minor principal stress at the same strain when the other factors are given.展开更多
基金supported by the National Natural Science Foundation for Distinguished Young Scholar (Grant No. 50825901)the Key Project of National Natural Science Foundation of China and Yalongjiang Hydro-electric Development Joint Research Fund (Grant No. 50639050)+2 种基金the Public Service Sector R&D Project of Ministry of Water Resource of China(Grant No. 200801014)the Fundamental Research Funds for the Central Universities (Grant No. 2010B15014)Scientific Innovation Research Scheme for Jiangsu University Graduate (Grant No. CX10B_207Z)
文摘A 3D bounding surface model is established for rockfill materials,which can be applied to appropriately predict the deformation and the stabilization of rockfill dams.Firstly,an associated plastic flow rule for rockfill materials is investigated based on the elaborate data from the large-style triaxial compression tests and the true triaxial tests.Secondly,the constitutive equations of the 3D bounding surface model are established by several steps.These steps include the bounding surface incorporating the general nonlinear strength criterion,stress-dilatancy equations,the evolution of the bounding surface and the bounding surface plasticity.Finally,the 3D bounding surface model is used to predict the mechanical behaviors of rockfill materials from the large-style triaxial compression tests and the true triaxial tests.Consequently,the proposed 3D bounding surface model can well capture such behaviors of rockfill materials as the strain hardening,the post-peak strain softening,and the volumetric strain contraction and expansion in both two-and three-dimensional stress spaces.
基金supported by the China Scholarship Council in the University of Wollongong(Grant No.201306710022)
文摘Particle size distribution significantly influences the mechanical response of the ballast under low confining pressure.However,particle breakage usually occurs and unfavorably degrades the particle size distribution of the ballast when sufficient load is applied.To model the triaxial stress-strain behavior and its associated evolution of particle size distribution of the ballast,a specific bounding surface model is proposed.The proposed model is based on the traditional bounding surface plasticity and a modified particle breakage index,which correlates the initial gradation and the ultimate gradation together with the current gradation.Simulation of the experimental results from the triaxial compression tests shows that the proposed model can predict the strain softening and volumetric expansion of the ballast under relatively lower confining pressure.It is also able to simulate the strain hardening and volumetric compression of the ballast under relatively higher confining pressure.Most importantly,the proposed approach was observed to have a great potential in predicting the evolution of the particle size distribution of the ballast.
基金supported by the National Natural Science Foundation of China for Distinguished Young Scholar (Grant No. 50825901)the Public Service Sector R&D Project of Ministry of Water Resource of China(Grant No. 200801014)+1 种基金the Fundamental Research Funds for the Central Universities (Grant No. 2011B14514)Jiangsu Civil Engineering Graduate Center for Innovation and Academic Communication Foundation
文摘A bounding surface model incorporating a unified nonlinear strength criterion is proposed.The proposed bounding surface model contains 9 model parameters,which can be determined from the conventional triaxial tests.The bounding surface model can reproduce such behaviours as the strain hardening,the post-peak strain softening,and the volumetric strain contraction and expansion.Based on the comparisons between the predictions and the test results,the proposed strength criterion and model can well reproduce the experimental results of the strength and stress-strain behaviours of rockfill material in three-dimensional stress space.The strength behaviour of rockfill material is summarized as:(a) the failure stress ratio decreases with the initial confining pressure on the meridian plane;(b) the failure deviatoric stress decreases with the Lode angle from 0o to 60o on the deviatoric plane.The stress ratio decreases with increasing one of such factors as the initial void ratio,the intermediate principal stress ratio and the minor principal stress at the same strain when the other factors are given.
