Microstructure and tensile properties of TC21 titanium alloy after near-isothermal forging with different parameters plus solution treatment and aging were investigated. It is found that the residual β matrix, which ...Microstructure and tensile properties of TC21 titanium alloy after near-isothermal forging with different parameters plus solution treatment and aging were investigated. It is found that the residual β matrix, which was strengthened by fine secondary α platelets forming during aging, exists in all the samples; while primary equiaxed α phase, bent lamellar α phase and α plates are simultaneously or individually present in one sample. The strength of alloy increases proportionally with increasing the content of residual β matrix, which is the result of increasing α/β interphase boundary. The plasticity of alloy has a downward trend as the content of residual β matrix increases. This attributes to the increase of fine secondary α platelets, which are cut by dislocations during the deformation. Additionally, coarse α plates with long axis parallel to the maximum resolved shear stress（MRSS） also reduce the plasticity of TC21 alloy.展开更多
The quench sensitivity and their influential factors of 7,021, 7,085, and 7,050 alloys were investigated by the end quenching test method and the measurement of electrical conductivity, hardness, and microstructure af...The quench sensitivity and their influential factors of 7,021, 7,085, and 7,050 alloys were investigated by the end quenching test method and the measurement of electrical conductivity, hardness, and microstructure after aging. The results indicate that 7,050 alloy has the largest changes with hardness decreasing from HV 199 to HV 167,and electrical conductivity increases from 16.6 to18.2 MS m-1when the distance from quenched end increases from 2 to 100 mm. Alloys 7,085 and 7,021 have relatively smaller changes. According to the relationship between the hardness and electrical conductivity of a supersaturated solid solution, 7,050 alloy has higher quench sensitivity than 7,085 and 7,021 alloys. The microstructure of 7,050 alloy with higher major alloy element（Zn ？ Mg ？ Cu） addition and Cu element addition is mostly affected by the changes of distance from quenched end. In 7,050 alloy, the size of intragranular precipitates is from about 10-200 nm, and the（sub） grain boundary precipitates are about 20-300 nm. Alloy 7,085 with lower Cu content is moderately affected, while 7,021 is least affected. It is found that with the increase of distance from quenched end, quenched-induced precipitate preferentially nucleates and grows in the（sub） grain boundary and then on the pre-existing Al3 Zr particles.展开更多
Magnesium alloy(AZ91D)composites reinforced with silicon carbide particle with different volume percentage were fabricated by two step stir casting process.The effect of changes in particle size and volume fraction of...Magnesium alloy(AZ91D)composites reinforced with silicon carbide particle with different volume percentage were fabricated by two step stir casting process.The effect of changes in particle size and volume fraction of SiC particles on physical and mechanical properties of composites were evaluated under as cast and heat treated(T6)conditions.The experimental results were compared with the standard theoretical models.The results reveal that the mechanical properties of composites increased with increasing SiC particles and decrease with increasing particle size.Distribution of particles and fractured surface were studied through SEM and the presence of elements is revealed by EDS study.展开更多
In order to improve mechanical properties of 6082 aluminum alloy,the SiC_(p)/Al 6082 composites were prepared by the addition of the micron-sized SiC_(p)articles combined with the squeeze casting.The effects of the Si...In order to improve mechanical properties of 6082 aluminum alloy,the SiC_(p)/Al 6082 composites were prepared by the addition of the micron-sized SiC_(p)articles combined with the squeeze casting.The effects of the SiC_(p)content and squeeze casting on the microstructure and mechanical properties of the 6082 aluminum alloy were investigated by SEM,EDS,TEM,tensile testing and hardness testing analysis methods.Research results exhibited that the SiC_(p)content and squeeze casting had a significant impact on the microstructure and mechanical properties of the 6082 aluminum alloy.The addition of the SiC_(p)refined the grain size of the 6082 aluminum alloy while caused the increase of the porosity with increasing the SiC_(p)content,especially in the permanent mold casting condition.Compared to the permanent mold casting,the squeeze casting obviously reduced pore defects,refined grain size and made the SiC_(p)distribute evenly as well as bond tightly with the Al matrix.The tensile strength,yield strength,elongation,elastic modulus and hardness of the 6082 aluminum alloy obtained with the SiC_(p)and squeeze casting were remarkably improved,and the optimal mechanical properties were obtained with a 2 wt.%SiC_(p),and they increased 10.73%,72.7%,193.9%,23.5%and 25.2%,respectively,compared to those of the6082 aluminum alloy obtained without SiC_(p)and squeeze casting.The fracture surface of the SiC_(p)/Al 6082 composites obtained with the squeeze casting was dense and exhibited a ductile fracture mode.展开更多
Three types of in-situ TiC(5 vol%,10 vol%and 15 vol%)reinforced high entropy alloy CoCrFeNi matrix composites were produced by vacuum induction smelting.The effect of two extreme cooling conditions(i.e.,slow cooling i...Three types of in-situ TiC(5 vol%,10 vol%and 15 vol%)reinforced high entropy alloy CoCrFeNi matrix composites were produced by vacuum induction smelting.The effect of two extreme cooling conditions(i.e.,slow cooling in fu rnace and rapid cooling in copper crucible)upon the microstructure and mechanical properties was examined.In the case of slow cooling in the furnace,TiC was found to form mostly along the grain boundaries for the 5 vol%samples.With the increase of TiC reinforcements,fibrous TiC appeared and extended into the matrix,leading to an increase in hardness.The ultimate tensile strength of the composites shows a marked variation with increasing TiC content;that is,425.6 MPa(matrix),372.8 MPa(5 vol%),550.4 MPa(10 vol%)and 334.3 MPa(15 vol%),while the elongation-to-failure(i.e.,ductility)decreases.The fracture pattern was found to transit from the ductile to cleavage fracture,as the TiC content increased.When the samples cooled rapidly in copper crucible,the TiC particles formed both along the grain boundaries and within the grains.With the increase of TiC volume fraction,both the hardness and ultimate tensile strength of the resulting composites improved steadily while the elongation-to-failure declined.Therefore,the fast cooling can be used to drastically improve the strength of in-situ TiC reinforced CoCrFeNi.For example,for the 15 vol%TiC/CoCrFeNi composite cooled in the copper crucible,the hardness and ultimate tensile strength can reach as high as 595 HV and 941.7 MPa,respectively.展开更多
CrMnFeCoNi high-entropy alloys(HEAs)exhibit an excellent combination of tensile strength and ductility at cryogenic temperatures.This study led to the introduction of a new method for the development of high-performan...CrMnFeCoNi high-entropy alloys(HEAs)exhibit an excellent combination of tensile strength and ductility at cryogenic temperatures.This study led to the introduction of a new method for the development of high-performance CrMnFeCoNi HEAs at cryogenic temperatures by jointly utilizing additive manufacturing(AM)and the addition of interstitial atoms.The interstitial oxygen present in the powder feedstock was transformed into beneficial nano-sized oxides during AM processing.The HEA nanocomposite fabricated using laser powder bed fusion(L-PBF)not only contains heterogeneous grains and substructures but also a high number density of nano-sized oxides.The tensile results revealed that the L-PBF HEA nanocomposite has superior yield strengths of 0.77 GPa and 1.15 GPa,and tensile strengths of 0.92 GPa and 1.45 GPa at 298 K and 77 K,respectively.In addition,the Charpy impact energies of the samples tested at 298 K and 77 K were measured as 176.2 J and 103.7 J,respectively.These results indicate that the L-PBF HEA nanocomposite successfully overcomes the well-known strength-toughness trade-off.The tensile deformation microstructure contained a relatively large number of deformation twins(DTs)at cryogenic temperature,a possible consequence of the decrease in the stacking fault energy with decreasing temperature.On the other hand,cracks were found to propagate along the grain boundaries at room temperature,whereas a transgranular crack was observed at cryogenic temperature in the specimens fractured as a result of the Charpy impact.展开更多
The squeeze cast process parameters of AZ80 magnesium alloy were optimized by morphological matrix. Experiments were conducted by varying squeeze pressure, die pre-heat temperature and pressure duration using L9（33）...The squeeze cast process parameters of AZ80 magnesium alloy were optimized by morphological matrix. Experiments were conducted by varying squeeze pressure, die pre-heat temperature and pressure duration using L9（33） orthogonal array of Taguchi method. In Taguchi method, a 3-level orthogonal array was used to determine the signal/noise ratio. Analysis of variance was used to determine the most significant process parameters affecting the mechanical properties. Mechanical properties such as ultimate tensile strength, elongation and hardness of the components were ascertained using multi variable linear regression analysis. Optimal squeeze cast process parameters were obtained.展开更多
Lightweight,high-modulus structural materials are highly desired in many applications like aerospace,automobile and biomedical instruments.As the lightest metallic structural material,magnesium(Mg)has great potential ...Lightweight,high-modulus structural materials are highly desired in many applications like aerospace,automobile and biomedical instruments.As the lightest metallic structural material,magnesium(Mg)has great potential but is limited by its low intrinsic Young’s modulus.This paper reviews the investigations on high-modulus Mg-based materials during the last decades.The nature of elastic modulus is introduced,and typical high-modulus Mg alloys and Mg matrix composites are reviewed.Specifically,Mg alloys enhance Young’s modulus of pure Mg mainly by introducing suitable alloying elements to promote the precipitation of high-modulus second phases in the alloy system.Differently,Mg matrix composites improve Young’s modulus by incorporating high-modulus particles,whiskers and fibers into the Mg matrix.The modulus strengthening effectiveness brought by the two approaches is compared,and Mg matrix composites stand out as a more promising solution.In addition,two well-accepted modulus prediction models(Halpin-Tsai and Rule of mixtures(ROM))for different Mg matrix composites are reviewed.The effects of reinforcement type,size,volume fraction and interfacial bonding condition on the modulus of Mg matrix composites are discussed.Finally,the existing challenges and development trends of high-modulus Mg-based materials are proposed and prospected.展开更多
The hot deformation behavior and microstructure evolution of GH3536-TiB2composites fabricated by powder metallurgy(PM)were examined in the temperature range of 950–1150℃ and strain rate range of 0.001–1 s^(-1). The...The hot deformation behavior and microstructure evolution of GH3536-TiB2composites fabricated by powder metallurgy(PM)were examined in the temperature range of 950–1150℃ and strain rate range of 0.001–1 s^(-1). The hot compression stress-strain curves and the constitutive equation were obtained. In addition, the hot processing map was drawn, which indicated that the appropriate hot working window was 950–1050℃/0.001–0.1 s^(-1)and 1050–1100℃/0.001–0.01 s^(-1). The microstructure analysis showed that the splitting and spheroidization of M3B2led to a decrease in size and volume fraction at 950–1100℃. At 1150℃,the eutectic microstructure of M_(3)B_(2)+ γ was formed due to the dissolution of M_(3)B_(2), which caused macroscopic cracking of the deformed sample. Additionally, the deformation temperature and the strain rate had little effect on the size and volume fraction of M_(3)B_(2). Besides, discontinuous dynamic recrystallization(DDRX) and continuous dynamic recrystallization(CDRX) were found in the deformed microstructure, while the former was dominant. Within the test range of this work, the dynamic recrystallization(DRX) fraction of the deformed composites was high due to the bulging nucleation of numerous interfaces. The DRX grain size increased with increasing deformation temperature or decreasing strain rate. Texture analysis showed that the deformation texture of <101>//compression direction RD existed in the matrix when the deformation temperature was below 1100℃, and the texture type became <001>//RD at 1100℃. Additionally, it was also found that the <001>//RD texture was formed in M3B2under the strain rates of 0.1 and 0.01 s^(-1).展开更多
High-cost pre-alloyed powder is the bottleneck problem that limits the widespread application of additivemanufactured shape memory alloys.In this work,the lowcost ternary NiTiFe shape memory alloy is fabricated by las...High-cost pre-alloyed powder is the bottleneck problem that limits the widespread application of additivemanufactured shape memory alloys.In this work,the lowcost ternary NiTiFe shape memory alloy is fabricated by laser powder bed fusion(LPBF)technique via mechanically mixed pre-alloy NiTi powder and varying contents pure Fe powder(1,2,3 wt%).All NiTiFe alloys show a relative density of up to 99.8%by optimizing the LPBF processing parameters.Owing to the heterogeneous nucleation effect of micron-sized Fe particles,both grain refinement and texture weakening are generated in the NiTiFe alloys,accompanied by the reduction of dislocation density.For the room-temperature mechanical properties,the NiTi-3Fe alloy shows the highest microhardness of HV370,but the fracture strength and elongation reduce to1701 MPa and 23%simultaneously.The evolution of mechanical properties is attributed to the high internal defects,low dislocation density and the incoherent oxide.Moreover,the NiTi-3Fe alloy shows the quasi-linear superelasticity behavior;the superelastic recoverable strain of NiTi-1Fe and NiTi-2Fe decreased with the increase in Fe content.This study provided a new-fangled insight for the development of multi-component NiTi-based shape memory alloys by additive manufacturing.展开更多
Copper alloy composite bit matrix was prepared by pressureless vacuum infiltration,using at least one of the three kinds of tungsten carbide particles,for example,irregular cast tungsten carbide,monocrystalline tungst...Copper alloy composite bit matrix was prepared by pressureless vacuum infiltration,using at least one of the three kinds of tungsten carbide particles,for example,irregular cast tungsten carbide,monocrystalline tungsten carbide and sintered reduced tungsten carbide particles.The effects of powder particle morphology,particle size and mass fraction of tungsten carbide on the microstructure and mechanical properties of copper alloy composite were investigated by means of scanning electron microscopy,X-ray diffraction and abrasive wear test in detail.The results show that tungsten carbide morphology and particle size have obvious effects on the mechanical properties of copper alloy composites.Cast tungsten carbide partially dissolved in the copper alloy binding phase,and layers of Cu_(0.3)W_(0.5)Ni_(0.1)Mn_(0.1)C phase with a thickness of around 8–15μm were formed on the edge of the cast tungsten carbide.When 45%irregular crushed fine cast tungsten carbide and 15%monocrystalline cast tungsten carbide were used as the skeleton,satisfactory comprehensive performance of the reinforced copper alloy composite bit matrix was obtained,with the bending strength,impact toughness and hardness reaching 1048 MPa,4.95 J/cm^(2) and 43.6 HRC,respectively.The main wear mechanism was that the tungsten carbide particles firstly protruded from the friction surface after the copper alloy matrix was worn,and then peeled off from the matrix when further wear occurred.展开更多
基金Projects(51205319,51101119)supported by the National Natural Science Foundation of China
文摘Microstructure and tensile properties of TC21 titanium alloy after near-isothermal forging with different parameters plus solution treatment and aging were investigated. It is found that the residual β matrix, which was strengthened by fine secondary α platelets forming during aging, exists in all the samples; while primary equiaxed α phase, bent lamellar α phase and α plates are simultaneously or individually present in one sample. The strength of alloy increases proportionally with increasing the content of residual β matrix, which is the result of increasing α/β interphase boundary. The plasticity of alloy has a downward trend as the content of residual β matrix increases. This attributes to the increase of fine secondary α platelets, which are cut by dislocations during the deformation. Additionally, coarse α plates with long axis parallel to the maximum resolved shear stress（MRSS） also reduce the plasticity of TC21 alloy.
基金financially supported by the National Natural Science Foundation of China (No. 51274046)
文摘The quench sensitivity and their influential factors of 7,021, 7,085, and 7,050 alloys were investigated by the end quenching test method and the measurement of electrical conductivity, hardness, and microstructure after aging. The results indicate that 7,050 alloy has the largest changes with hardness decreasing from HV 199 to HV 167,and electrical conductivity increases from 16.6 to18.2 MS m-1when the distance from quenched end increases from 2 to 100 mm. Alloys 7,085 and 7,021 have relatively smaller changes. According to the relationship between the hardness and electrical conductivity of a supersaturated solid solution, 7,050 alloy has higher quench sensitivity than 7,085 and 7,021 alloys. The microstructure of 7,050 alloy with higher major alloy element（Zn ？ Mg ？ Cu） addition and Cu element addition is mostly affected by the changes of distance from quenched end. In 7,050 alloy, the size of intragranular precipitates is from about 10-200 nm, and the（sub） grain boundary precipitates are about 20-300 nm. Alloy 7,085 with lower Cu content is moderately affected, while 7,021 is least affected. It is found that with the increase of distance from quenched end, quenched-induced precipitate preferentially nucleates and grows in the（sub） grain boundary and then on the pre-existing Al3 Zr particles.
基金This work was supported by Department of Science and Technology,Government of India,under Grant No:RP02197.
文摘Magnesium alloy(AZ91D)composites reinforced with silicon carbide particle with different volume percentage were fabricated by two step stir casting process.The effect of changes in particle size and volume fraction of SiC particles on physical and mechanical properties of composites were evaluated under as cast and heat treated(T6)conditions.The experimental results were compared with the standard theoretical models.The results reveal that the mechanical properties of composites increased with increasing SiC particles and decrease with increasing particle size.Distribution of particles and fractured surface were studied through SEM and the presence of elements is revealed by EDS study.
基金financially supported by the National Key Research and Development Program of China(Nos.2020YFB2008300 and 2020YFB2008304)the State Key Laboratory of High Performance Complex Manufacturing in CSU(No.Kfkt2019-01)the Analytical and Testing Center,HUST。
文摘In order to improve mechanical properties of 6082 aluminum alloy,the SiC_(p)/Al 6082 composites were prepared by the addition of the micron-sized SiC_(p)articles combined with the squeeze casting.The effects of the SiC_(p)content and squeeze casting on the microstructure and mechanical properties of the 6082 aluminum alloy were investigated by SEM,EDS,TEM,tensile testing and hardness testing analysis methods.Research results exhibited that the SiC_(p)content and squeeze casting had a significant impact on the microstructure and mechanical properties of the 6082 aluminum alloy.The addition of the SiC_(p)refined the grain size of the 6082 aluminum alloy while caused the increase of the porosity with increasing the SiC_(p)content,especially in the permanent mold casting condition.Compared to the permanent mold casting,the squeeze casting obviously reduced pore defects,refined grain size and made the SiC_(p)distribute evenly as well as bond tightly with the Al matrix.The tensile strength,yield strength,elongation,elastic modulus and hardness of the 6082 aluminum alloy obtained with the SiC_(p)and squeeze casting were remarkably improved,and the optimal mechanical properties were obtained with a 2 wt.%SiC_(p),and they increased 10.73%,72.7%,193.9%,23.5%and 25.2%,respectively,compared to those of the6082 aluminum alloy obtained without SiC_(p)and squeeze casting.The fracture surface of the SiC_(p)/Al 6082 composites obtained with the squeeze casting was dense and exhibited a ductile fracture mode.
基金This work was supported financially by the National Natural Science Foundation of China(Nos.51571118 and 51371098)the Natural Science Foundation of Jiangsu Province,China(No.BK20141308)Jiangsu province Science and Technology Plan Project,China(No.BE2018753/KJ185629).
文摘Three types of in-situ TiC(5 vol%,10 vol%and 15 vol%)reinforced high entropy alloy CoCrFeNi matrix composites were produced by vacuum induction smelting.The effect of two extreme cooling conditions(i.e.,slow cooling in fu rnace and rapid cooling in copper crucible)upon the microstructure and mechanical properties was examined.In the case of slow cooling in the furnace,TiC was found to form mostly along the grain boundaries for the 5 vol%samples.With the increase of TiC reinforcements,fibrous TiC appeared and extended into the matrix,leading to an increase in hardness.The ultimate tensile strength of the composites shows a marked variation with increasing TiC content;that is,425.6 MPa(matrix),372.8 MPa(5 vol%),550.4 MPa(10 vol%)and 334.3 MPa(15 vol%),while the elongation-to-failure(i.e.,ductility)decreases.The fracture pattern was found to transit from the ductile to cleavage fracture,as the TiC content increased.When the samples cooled rapidly in copper crucible,the TiC particles formed both along the grain boundaries and within the grains.With the increase of TiC volume fraction,both the hardness and ultimate tensile strength of the resulting composites improved steadily while the elongation-to-failure declined.Therefore,the fast cooling can be used to drastically improve the strength of in-situ TiC reinforced CoCrFeNi.For example,for the 15 vol%TiC/CoCrFeNi composite cooled in the copper crucible,the hardness and ultimate tensile strength can reach as high as 595 HV and 941.7 MPa,respectively.
基金supported by a National Research Foundation of Korea(NRF)grant funded by the Korean government(MEST)(No.2019R1A2C1008904)。
文摘CrMnFeCoNi high-entropy alloys(HEAs)exhibit an excellent combination of tensile strength and ductility at cryogenic temperatures.This study led to the introduction of a new method for the development of high-performance CrMnFeCoNi HEAs at cryogenic temperatures by jointly utilizing additive manufacturing(AM)and the addition of interstitial atoms.The interstitial oxygen present in the powder feedstock was transformed into beneficial nano-sized oxides during AM processing.The HEA nanocomposite fabricated using laser powder bed fusion(L-PBF)not only contains heterogeneous grains and substructures but also a high number density of nano-sized oxides.The tensile results revealed that the L-PBF HEA nanocomposite has superior yield strengths of 0.77 GPa and 1.15 GPa,and tensile strengths of 0.92 GPa and 1.45 GPa at 298 K and 77 K,respectively.In addition,the Charpy impact energies of the samples tested at 298 K and 77 K were measured as 176.2 J and 103.7 J,respectively.These results indicate that the L-PBF HEA nanocomposite successfully overcomes the well-known strength-toughness trade-off.The tensile deformation microstructure contained a relatively large number of deformation twins(DTs)at cryogenic temperature,a possible consequence of the decrease in the stacking fault energy with decreasing temperature.On the other hand,cracks were found to propagate along the grain boundaries at room temperature,whereas a transgranular crack was observed at cryogenic temperature in the specimens fractured as a result of the Charpy impact.
基金Project (50975263) supported by the National Natural Science Foundation of ChinaProject (2011DFA50520) supported by International Science Technology Cooperation Program of China
文摘The squeeze cast process parameters of AZ80 magnesium alloy were optimized by morphological matrix. Experiments were conducted by varying squeeze pressure, die pre-heat temperature and pressure duration using L9（33） orthogonal array of Taguchi method. In Taguchi method, a 3-level orthogonal array was used to determine the signal/noise ratio. Analysis of variance was used to determine the most significant process parameters affecting the mechanical properties. Mechanical properties such as ultimate tensile strength, elongation and hardness of the components were ascertained using multi variable linear regression analysis. Optimal squeeze cast process parameters were obtained.
基金supported by“National Key Research&Development Program of China”(Grant No.2021YFB3703300)“National Natural Science Foundation of China”(Grant Nos.51971075,51971078,51871074,and51671066)+1 种基金“National Natural Science Foundation for Young Scientists of China”(Grant No.51801042)“Fundamental Research Funds for the Central Universities”(Grant No.FRFCU5710000918)。
文摘Lightweight,high-modulus structural materials are highly desired in many applications like aerospace,automobile and biomedical instruments.As the lightest metallic structural material,magnesium(Mg)has great potential but is limited by its low intrinsic Young’s modulus.This paper reviews the investigations on high-modulus Mg-based materials during the last decades.The nature of elastic modulus is introduced,and typical high-modulus Mg alloys and Mg matrix composites are reviewed.Specifically,Mg alloys enhance Young’s modulus of pure Mg mainly by introducing suitable alloying elements to promote the precipitation of high-modulus second phases in the alloy system.Differently,Mg matrix composites improve Young’s modulus by incorporating high-modulus particles,whiskers and fibers into the Mg matrix.The modulus strengthening effectiveness brought by the two approaches is compared,and Mg matrix composites stand out as a more promising solution.In addition,two well-accepted modulus prediction models(Halpin-Tsai and Rule of mixtures(ROM))for different Mg matrix composites are reviewed.The effects of reinforcement type,size,volume fraction and interfacial bonding condition on the modulus of Mg matrix composites are discussed.Finally,the existing challenges and development trends of high-modulus Mg-based materials are proposed and prospected.
基金supported by the National Key R&D Program of China (Grant No. 2021YFB3701203)the National Natural Science Foundation of China (Grant Nos. U22A20113, 52171137, 52201156 and 52071116)+2 种基金Heilongjiang Touyan Team Program, Heilongjiang Provincial Natural Science Foundation of China (Grant No. TD2020E001)Heilongjiang Postdoctoral Fund (Grant No. LBH-Z20058)Key Laboratories Foundation (Grant No. 6142910220206)。
文摘The hot deformation behavior and microstructure evolution of GH3536-TiB2composites fabricated by powder metallurgy(PM)were examined in the temperature range of 950–1150℃ and strain rate range of 0.001–1 s^(-1). The hot compression stress-strain curves and the constitutive equation were obtained. In addition, the hot processing map was drawn, which indicated that the appropriate hot working window was 950–1050℃/0.001–0.1 s^(-1)and 1050–1100℃/0.001–0.01 s^(-1). The microstructure analysis showed that the splitting and spheroidization of M3B2led to a decrease in size and volume fraction at 950–1100℃. At 1150℃,the eutectic microstructure of M_(3)B_(2)+ γ was formed due to the dissolution of M_(3)B_(2), which caused macroscopic cracking of the deformed sample. Additionally, the deformation temperature and the strain rate had little effect on the size and volume fraction of M_(3)B_(2). Besides, discontinuous dynamic recrystallization(DDRX) and continuous dynamic recrystallization(CDRX) were found in the deformed microstructure, while the former was dominant. Within the test range of this work, the dynamic recrystallization(DRX) fraction of the deformed composites was high due to the bulging nucleation of numerous interfaces. The DRX grain size increased with increasing deformation temperature or decreasing strain rate. Texture analysis showed that the deformation texture of <101>//compression direction RD existed in the matrix when the deformation temperature was below 1100℃, and the texture type became <001>//RD at 1100℃. Additionally, it was also found that the <001>//RD texture was formed in M3B2under the strain rates of 0.1 and 0.01 s^(-1).
基金financially supported by the National Natural Science Foundation of China(No.52201225)the Post-doctoral Foundation Project of Shenzhen Polytechnic(No.6021330013K0)+4 种基金the Additive Manufacturing Technology R&D Center(No.602331004PQ)Guangdong Provincial General University Innovation Team Project(No.2020KCXTD047)Shenzhen ScienceandTechnologyInnovationCommission(No.JSGG20200701095008016)Shenzhen Science and Technology Program(No.RCBS20221008093241051)the Natural Science Foundation of Guangdong Province(No.2022A1515110389)。
文摘High-cost pre-alloyed powder is the bottleneck problem that limits the widespread application of additivemanufactured shape memory alloys.In this work,the lowcost ternary NiTiFe shape memory alloy is fabricated by laser powder bed fusion(LPBF)technique via mechanically mixed pre-alloy NiTi powder and varying contents pure Fe powder(1,2,3 wt%).All NiTiFe alloys show a relative density of up to 99.8%by optimizing the LPBF processing parameters.Owing to the heterogeneous nucleation effect of micron-sized Fe particles,both grain refinement and texture weakening are generated in the NiTiFe alloys,accompanied by the reduction of dislocation density.For the room-temperature mechanical properties,the NiTi-3Fe alloy shows the highest microhardness of HV370,but the fracture strength and elongation reduce to1701 MPa and 23%simultaneously.The evolution of mechanical properties is attributed to the high internal defects,low dislocation density and the incoherent oxide.Moreover,the NiTi-3Fe alloy shows the quasi-linear superelasticity behavior;the superelastic recoverable strain of NiTi-1Fe and NiTi-2Fe decreased with the increase in Fe content.This study provided a new-fangled insight for the development of multi-component NiTi-based shape memory alloys by additive manufacturing.
基金supported by the National Natural Science Foundation of China(Grant No.52074365)grateful to the Sichuan Science and Technology Program,China(Grant No.2022YFG0289)+2 种基金sponsored by the Funding Project of Key Laboratory of Sichuan Province for comprehensive Utilization of Vanadium and Titanium Resources,China(Grant No.2018FTSZ26)the Project Supported by the Opening Project of Material Corrosion and Protection Key Laboratory of Sichuan province,China(Grant Nos.2021CL26,GK202104,and GK202106)supported by the Ph.D.Programs Foundation of Sichuan University of Science and Engineering,China(Grant No.2021RC18).
文摘Copper alloy composite bit matrix was prepared by pressureless vacuum infiltration,using at least one of the three kinds of tungsten carbide particles,for example,irregular cast tungsten carbide,monocrystalline tungsten carbide and sintered reduced tungsten carbide particles.The effects of powder particle morphology,particle size and mass fraction of tungsten carbide on the microstructure and mechanical properties of copper alloy composite were investigated by means of scanning electron microscopy,X-ray diffraction and abrasive wear test in detail.The results show that tungsten carbide morphology and particle size have obvious effects on the mechanical properties of copper alloy composites.Cast tungsten carbide partially dissolved in the copper alloy binding phase,and layers of Cu_(0.3)W_(0.5)Ni_(0.1)Mn_(0.1)C phase with a thickness of around 8–15μm were formed on the edge of the cast tungsten carbide.When 45%irregular crushed fine cast tungsten carbide and 15%monocrystalline cast tungsten carbide were used as the skeleton,satisfactory comprehensive performance of the reinforced copper alloy composite bit matrix was obtained,with the bending strength,impact toughness and hardness reaching 1048 MPa,4.95 J/cm^(2) and 43.6 HRC,respectively.The main wear mechanism was that the tungsten carbide particles firstly protruded from the friction surface after the copper alloy matrix was worn,and then peeled off from the matrix when further wear occurred.
