The present work involves the development of siliconized epoxy resin to overcome the drawback of epoxy resin like poor impact strength, high rigidity and moisture absorbing nature because of which they are not applied...The present work involves the development of siliconized epoxy resin to overcome the drawback of epoxy resin like poor impact strength, high rigidity and moisture absorbing nature because of which they are not applied as corrosion resistant coating. By embedding silicone into the back bone of polymeric resin the above drawback can be reduced to substantial level. For achieving this, siliconised epoxy resins were prepared by reacting amine terminated silicone resin with novolac epoxy resin and meta-phenylenediamine was used as curing agent. The applied films of coating were baked at 150oC. Cured films were evaluated for their thermal, mechanical, chemical and corrosion resistance properties to ascertain the commercial utility of these eco-friendly resin for use in anti corrosive formulations. The siliconized epoxy resins system was found to exhibit good thermal and anticorrosive properties.展开更多
Electrochemical impedance spectroscopy (EIS) in the l00 kHz-10 mHz frequency range was employed as the main electrochemical technique to study the corrosion protection behaviour of zinc rich epoxy paint in 3% NaCl sol...Electrochemical impedance spectroscopy (EIS) in the l00 kHz-10 mHz frequency range was employed as the main electrochemical technique to study the corrosion protection behaviour of zinc rich epoxy paint in 3% NaCl solution. The EIS results obtained at the open-circuit corrosion potential have been interpreted using a model involving the impedance of particle to particle contact to account for the increasing resistance between zinc particles with immersion period, in addition to the impedance due to the zinc surface oxide layer and the electrical resistivity of the binder. Galvanic current and dc potential measurements allowed us to conclude that the cathodic protection effect of the paint takes some time to be achieved. The loss of cathodic protection is due to a double effect: the decrease of the Zn/Fe area ratio due to Zn corrosion and the loss of electric contact between Zn to Zn particles. Even when the cathodic protection effect by Zn dust become weak, the substrate steel is still protected against corrosion due to the barrier nature of the ZRP film reinforced by Zn.展开更多
Coating slurries for making anodes and cathodes of lithium batteries contain a large percentage of solid particles of different chemicals, sizes and shapes in highly viscous media. A thorough mixing of these slurries ...Coating slurries for making anodes and cathodes of lithium batteries contain a large percentage of solid particles of different chemicals, sizes and shapes in highly viscous media. A thorough mixing of these slurries poses a major challenge in the battery manufacturing process. Several types of mixing devices and mixing methods were examined. The conventional turbine stirrers or ball mill mixers could be adequately used for the preparation of anode slurries, but not suitable for cathode slurries. In this study, a newly three-dimensional mixer, in conjunction with a multi-stage mixing sequence was proposed. The mixing effectiveness was examined by means of rheological measurements and flow visualization techniques. Preliminary electrical performance results indicated that the battery obtained using the 3D mixing device with a multi-stage mixing sequence was more efficient to those obtained from conventional methods.展开更多
This paper describes a concept for an independent and redundant safety concept for Lithium batteries in Electric and Hybrid Electric Vehicles. This concept includes an emergency cooling system based on pressurized car...This paper describes a concept for an independent and redundant safety concept for Lithium batteries in Electric and Hybrid Electric Vehicles. This concept includes an emergency cooling system based on pressurized carbon dioxide (CO2). Since carbon dioxide (CO2) is a possible medium of future mobile air conditioning (MAC) systems, the MAC system can be utilized for the one-time emergency cooling described in this paper. In the first part of the paper, some major safety aspects of automotive Li batteries are highlighted. In the second section, the paper describes a technical approach, how these batteries can be made safer. Pressurized CO2, which is a promising candidate for cooling liquids used in future mobile air conditioning (MAC) systems, is used to effectively cool down an overheating or up-heating battery in a critical state. The safety system thereby is not based on an electrical effect, but on a direct and fast-reacting thermal conduction, avoiding a thermal runaway of individual cells. The application of the proposed system is to act preventively just before the thermal runaway gets uncontrollable. In this case, the limited amount of CO2, which is available in the MAC system, fulfils the emergency cooling requirements. The combination of standard car components for the concept leads to an only moderate increase of the total weight and the additional system costs. Therefore, the described system might be of interest for car, battery and air conditioning system producers. This paper explains that the synergetic combination of CO2-based MAC systems and Li-based batteries is an innovative approach to improve environmental compatibility in future vehicles. The concept is proven experimentally on a lab scale with battery cells and battery packs consisting of four serially connected cells, respectively.展开更多
In this paper we demonstrate that the residual stress introduced by several different surface finishes affects the critical current density for passivation and the passive current density in the anodic polarization cu...In this paper we demonstrate that the residual stress introduced by several different surface finishes affects the critical current density for passivation and the passive current density in the anodic polarization curve of austenitic stainless steel and that those critical current densities can be reduced by controlling the residual stress by applying a cavitating jet to the backs of specimens. The results show that the current density either increased or decreased depending on the surface finish, and that was decreased by introducing compressive residual stress for all surface finishes.展开更多
The performance of a newly designed tri-lobe industrial lobe pump of high capacity is simulated by using commercial CFD solver Ansys Fluent. A combination of user-defined-functions and meshing strategies is employed t...The performance of a newly designed tri-lobe industrial lobe pump of high capacity is simulated by using commercial CFD solver Ansys Fluent. A combination of user-defined-functions and meshing strategies is employed to capture the rotation of the lobes. The numerical model is validated by comparing the simulated results with the literature values. The processes of suction, displacement, compression and exhaust are accurately captured in the transient simulation. The fluid pressure value remains in the range of inlet pressure value till the processes of suction and displacement are over. The instantaneous process of compression is accurately captured in the simulation. The movement of a particular working chamber is traced along the gradual degree of lobe’s rotation. At five different degrees of lobe’s rotation, pressure contour plots are reported which clearly shows the pressure values inside the working chamber. Each pressure value inside the working chamber conforms to the particular process in which the working chamber is operating. Finally, the power requirement at the shaft of rotation is estimated from the simulated values. The estimated value of power requirement is 3.61 BHP FHP whereas the same calculated theoretically is 3 BHP FHP. The discrepancy is attributed to the assumption of symmetry of blower along the thickness.展开更多
Currently a technique widely used for gold extraction is mercury by amalgamation technique, the tailing produced pollutes water of all kinds, so it is necessary to develop a form of selective mitigation, for which it ...Currently a technique widely used for gold extraction is mercury by amalgamation technique, the tailing produced pollutes water of all kinds, so it is necessary to develop a form of selective mitigation, for which it is necessary to use complexing agents based on calixarene functionalized with mercury sequestering agents. These are immobilized by adding supports based on natural silica to form polymers and make them insoluble in all types of solvents, so that they can be used as an extractor and at the same time regenerate to their original properties for continuous reuse.展开更多
Lithium element has attracted remarkable attraction for energy storage devices, over the past 30 years. Lithium is a light element and exhibits the low atomic number 3, just after hydrogen and helium in the periodic t...Lithium element has attracted remarkable attraction for energy storage devices, over the past 30 years. Lithium is a light element and exhibits the low atomic number 3, just after hydrogen and helium in the periodic table. The lithium atom has a strong tendency to release one electron and constitute a positive charge, as Li<sup> </sup>. Initially, lithium metal was employed as a negative electrode, which released electrons. However, it was observed that its structure changed after the repetition of charge-discharge cycles. To remedy this, the cathode mainly consisted of layer metal oxide and olive, e.g., cobalt oxide, LiFePO<sub>4</sub>, etc., along with some contents of lithium, while the anode was assembled by graphite and silicon, etc. Moreover, the electrolyte was prepared using the lithium salt in a suitable solvent to attain a greater concentration of lithium ions. Owing to the lithium ions’ role, the battery’s name was mentioned as a lithium-ion battery. Herein, the presented work describes the working and operational mechanism of the lithium-ion battery. Further, the lithium-ion batteries’ general view and future prospects have also been elaborated.展开更多
A series of six pyrazoles was synthesized by Michael-type addition reaction. The molecules 5-amino-1-aryl-1H-pyrazole-4-carbonitrile (3a-f) were synthesized from (ethoxymethylene)malo-nonitrile (1) and fluorinated and...A series of six pyrazoles was synthesized by Michael-type addition reaction. The molecules 5-amino-1-aryl-1H-pyrazole-4-carbonitrile (3a-f) were synthesized from (ethoxymethylene)malo-nonitrile (1) and fluorinated and non-fluorinated aryl hydrazines (2a-f) using ethanol and fluorinated ethanol as solvents at reflux. An excellent regio-selectivity was found when pyrazole derivatives were formed as an exclusive product. No other regioisomer or uncyclised hydrazide was observed. Their structures were confirmed by spectroscopy data (1H, 13C, 19F, COSY (correlation spectroscopy), HSQC (heteronuclear single-quantum correlation spectroscopy) and HMBC (heteronuclear multiple-bond correlation spectroscopy);MS (mass-spectrometry). The yields ranged from good to excellent (47% - 93%) under mild reaction conditions. It would indicate a high selectivity in the one-step work procedure. These products (3a-f) and derivatives have a potential academic and industrial use as key intermediates, in special, for application in crop protection.展开更多
Large quantities of spent hydrodesulfurization (HDS) catalysts are available from petrochemical industry. Disposal of spent catalyst is a problem as it falls under the category of hazardous industrial waste due to its...Large quantities of spent hydrodesulfurization (HDS) catalysts are available from petrochemical industry. Disposal of spent catalyst is a problem as it falls under the category of hazardous industrial waste due to its vanadium concentration. Most of these catalysts are usually supported on alumina containing a variable percentage of elements such as nickel or molybdenum. Hence these catalysts contain environmentally critical, and economically valuable metals such as molyb denum, vanadium, and, nickel. In this paper, a spent HDS catalyst was treated with caustic soda solution. Parameters such as temperature, time, and NaOH solution concentration have been studied thoroughly, in order to settle the appropriate conditions for the maximum recovery of molybdenum and vanadium. Under the best leaching conditions (20 %w NaOH, room temperature, 2 h) about 95% recovery of Mo and V was achieved, and the recovery of nickel obtained was of 99% in the form of NiAlO4.展开更多
Water is the most abundant liquid on the surface of the earth. It is a liquid whose properties are quite surprising, both as a pure liquid and as a solvent. Water is a very cohesive liquid: its melting and vaporizatio...Water is the most abundant liquid on the surface of the earth. It is a liquid whose properties are quite surprising, both as a pure liquid and as a solvent. Water is a very cohesive liquid: its melting and vaporization temperatures are very high for a liquid that is neither ionic nor metallic, and whose molar mass is low. Thus, water remains liquid at atmospheric pressure up to 100C while similar molecules such as H2S, H2Se, H2Te for example would give a vaporization temperature close to 80C. This cohesion is in fact ensured by hydrogen bonds between water molecules. This type of bonds between neighboring molecules, hydrogen bonds, is quite often found in chemistry [1] [2]. Any change in the state of aggregation of a substance occurs with the absorption or release of a certain amount of latent heat of transformation. Latent heat of fusion, vaporization or sublimation is the ratio of the energy supplied as heat to the mass of the substance that is melted, vaporized or sublimated. As a result of the reversibility of the processes, the fusion heat is equal to the heat released in the reverse process: crystallization and solidification heat. And likewise the heat of vaporization is equal to the heat of condensation. This equality of heat is often used to determine experimentally either of these quantities. There are two main measurement methods: 1) Direct measurement using the calorimeter, 2) Indirect measure based on the use of the VantHoff relationship. The objective of this work is to measure the latent heat of water vaporization and verify the compatibility of the experimental values with the values given by the tables using the indirect method.展开更多
In global industrialization, efforts have been made to increase the rate of heat transfer in heat exchanger, minimizing the size of heat exchanger to reduce cost as well as increasing the effectiveness. Helical coil h...In global industrialization, efforts have been made to increase the rate of heat transfer in heat exchanger, minimizing the size of heat exchanger to reduce cost as well as increasing the effectiveness. Helical coil heat exchanger (HCHE) has been proven to be effective in improving heat transfer due to its large surface area. In this study, HCHE was designed to provide hot air needed for fluidized bed drying processes. The HCHE design model was fabricated and evaluated to study the efficiency of the hot air output for a laboratory fluidized bed dryer. The mathematical model for estimation of the final (output) temperature of air, Taf, passing through the HCHE was developed and validated experimentally. The drying of bitter kola particulates was carried out with a drying temperature of 50C 3C and a bed height-to-bed diameter ratio (H/D) of 1.5. The time taken to dry bitter kola particulates to 0.4% moisture content was 1 hour 45 minutes. Hence, HCHE is recommended for use in the production of hot for laboratory-scale fluidized bed dryers.展开更多
In this study, a homogeneous alkaline catalyst was used in the production of biodiesel from raw and refined castor oil feedstock. The effect of potassium hydroxide (KOH) as a catalyst between the two feedstocks, raw a...In this study, a homogeneous alkaline catalyst was used in the production of biodiesel from raw and refined castor oil feedstock. The effect of potassium hydroxide (KOH) as a catalyst between the two feedstocks, raw and refined castor oil was compared. The transesterification technique was utilized in this study, aiming to investigate the effect of different parameters, which include the reaction temperature, methanol-to-oil mole ratio, and catalyst concentration at a constant period of 90 minutes. The result revealed the performance of the KOH catalyst on raw castor oil yielded 98.49% FAME, which was higher than the refined castor oil which yielded 97.9% FAME. The optimal conditions obtained from refined castor oil were applied to raw castor oil because of the same properties. The fuel quality of castor oil and produced biodiesel were tested for physicochemical properties.展开更多
In the emerging world of biotech innovation, the fast-to-clinic/market strategy has emerged as a critical “mantra” for biotech, investors, and CDMOs. This approach addresses the escalating costs and complexities of ...In the emerging world of biotech innovation, the fast-to-clinic/market strategy has emerged as a critical “mantra” for biotech, investors, and CDMOs. This approach addresses the escalating costs and complexities of research and development by streamlining the path from concept to clinical trials and, ultimately, to market. The article delves into the intricacies of implementing a fast-to-clinic/market strategy, underlining the empowering role of strategic decision-making in preclinical and commercial stages. The plan advocates for a phase-appropriate approach, where the development decision is tailored to each phase of the product’s lifecycle. This ensures that resources are allocated efficiently, risks are managed effectively, and the product can move through the development pipeline accelerated without compromising quality or regulatory compliance. The article also discusses the role of CDMOs in facilitating rapid product development and the essential factors biotech companies must consider when selecting a partner for outsourcing. These factors include the CDMO’s expertise in navigating regulatory landscapes, technological capabilities, and ability to scale processes efficiently. Moreover, the article stresses the importance of agility and flexibility in the fast-to-clinic/market approach. Biotech companies are encouraged to adopt adaptable strategies that respond to the fast-evolving regulatory and market landscapes.展开更多
Organic molecules that exhibit long persistent luminescence (LPL) are rapidly gaining attention for a variety of applications. In this study, organic molecules with simple structures were selected and organic long per...Organic molecules that exhibit long persistent luminescence (LPL) are rapidly gaining attention for a variety of applications. In this study, organic molecules with simple structures were selected and organic long persistent luminescence (OLPL) crystals were prepared. The crystal structure of the prepared OLPL crystal was elucidated and the guideline for the design of OLPL crystal was clarified. LPL was observed in OLPL crystals prepared with TMB as the guest molecule and 1,2-bis(diphenylphosphino)ethane as the host molecule. XRD measurements of the OLPL crystals suggest that the guest molecule is a solid solution substituted in the stable crystal structure of the host molecule in a lattice-shrinking direction.展开更多
In the present study, energetic and entropic changes are investigated on a comparative basis, as they occur in the volume changes of an ideal gas in the Carnot cycle and in the course of the chemical reaction in a lea...In the present study, energetic and entropic changes are investigated on a comparative basis, as they occur in the volume changes of an ideal gas in the Carnot cycle and in the course of the chemical reaction in a lead-acid battery. Differences between reversible and irreversible processes have been worked out, in particular between reversibly exchanged entropy (∆<sub>e</sub>S) and irreversibly produced entropy (∆<sub>i</sub>S). In the partially irreversible case, ∆<sub>e</sub>S and ∆<sub>i</sub>S add up to the sum ∆S for the volume changes of a gas, and only this function has an exact differential. In a chemical reaction, however, ∆<sub>e</sub>S is independent on reversibility. It arises from the different intramolecular energy contents between products and reactants. Entropy production in a partially irreversible Carnot cycle is brought about through work-free expansions, whereas in the irreversible battery reaction entropy is produced via activated complexes, whereby a certain, variable fraction of the available chemical energy becomes transformed into electrical energy and the remaining fraction dissipated into heat. The irreversible reaction process via activated complexes has been explained phenomenologically. For a sufficiently high power output of coupled reactions, it is essential that the input energy is not completely reversibly transformed, but rather partially dissipated, because this can increase the process velocity and consequently its power output. A reduction of the counter potential is necessary for this purpose. This is not only important for man-made machines, but also for the viability of cells.展开更多
With the full growth of energy needs in the world, several studies are now focused on finding renewable sources. The aim of this work is to optimise biofuel formulation from a mixture design by studying physical prope...With the full growth of energy needs in the world, several studies are now focused on finding renewable sources. The aim of this work is to optimise biofuel formulation from a mixture design by studying physical properties, such as specific gravity and kinematic viscosity of various formulated mixtures. Optimization from the mixture plan revealed that in the chosen experimental domain, the optimal conditions are: 40% for used frying oil (UFO), 50% for bioethanol and 10% for diesel. These experimental conditions lead to a biofuel with a density of 0.84 and a kinematic viscosity of 2.97 cSt. These parameters are compliant with the diesel quality certificate in tropical areas. These density and viscosity values were determined according to respective desirability values of 0.68 and 0.75.展开更多
Nano-sized ZnO catalysts were prepared by a direct precipitation method under the optimal conditions (cal-cination of precursors at 550?C for 120 min). The as-synthesized ZnO catalysts were characterized by X-ray diff...Nano-sized ZnO catalysts were prepared by a direct precipitation method under the optimal conditions (cal-cination of precursors at 550?C for 120 min). The as-synthesized ZnO catalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and UV-Vis spectroscopy. The photocatalytic prop-erties of ZnO nanoparticles were investigated via methyl orange (MO) as a model organic compound under UV light irradiation. The influence of operating parameters on MO degradation including the amount of ZnO catalysts, pH value of solutions, and the photodegradation temperature was thoroughly examined. In addition, the kinetic process of photocatalytic degradation of MO using nano-sized ZnO catalyst was also examined, and the degradation of MO follow the first order kinetics.展开更多
Various concepts for oil evaporation prediction are summarized. Models can be divided into those models that use the basis of air-boundary-regulation or those that do not. Experiments were conducted to determine if oi...Various concepts for oil evaporation prediction are summarized. Models can be divided into those models that use the basis of air-boundary-regulation or those that do not. Experiments were conducted to determine if oil and petroleum evaporation is regulated by the saturation of the air boundary layer. Experiments included the examination of the evaporation rate with and without wind, in which case it was found that evaporation rates were similar for all wind conditions and no-wind conditions. Experiments where the area and mass varied showed that boundary-layer regulation was not governing for petroleum products. Under all experimental and environmental conditions, oils or petroleum products were not found to be boundary-layer regulated. Experiments on the rate of evaporation of pure compounds showed that compounds larger than Decane were not boundary-layer regulated. Many oils and petroleum products contain few compounds smaller than decane, and this explains why their evaporation is not air boundary-layer limited. Comparison of the air saturation levels of various oils and petroleum products shows that the saturation concentration of water, which is strongly air boundary-regulated, is significantly less than that of several petroleum hydrocarbons. Lack of air boundary-layer regulation for oils is shown to be a result of both this higher saturation concentration as well as a low (below boundary-layer value) evaporation rate.展开更多
The aim of this work was to investigate the aerobic degradation of high-strength industrial (refinery) wastewaters in the inverse fluidized bed biological reactor, in which polypropylene particles of density 910 kg/m3...The aim of this work was to investigate the aerobic degradation of high-strength industrial (refinery) wastewaters in the inverse fluidized bed biological reactor, in which polypropylene particles of density 910 kg/m3 were fluidized by an upward flow of gas through a bed. Measurements of chemical oxygen demand (COD) versus residence time t were performed for various ratios of settled bed volume to reactor volume (Vb/VR) and air velocities u. The largest COD reduction, namely, from 54,840 to 2,190 mg/l, i.e. a 96% COD decrease, was achieved when the reactor was operated at the ratio (Vb/VR) = 0.55, air velocity u = 0.046 m/s and t = 65 h. Thus, these values of (Vb/VR), u and t can be considered as the optimal operating parameters for a reactor when used in treatment of high-strength refinery wastewaters. In the treatment operation conducted in a reactor optimally controlled at (Vb/VR) = 0.55, u = 0.046 m/s and t = 65 h, the conversions obtained for all phenolic constituents of the wastewater were larger than 95%. The conversions of about 90% were attained for other hydrocarbons.展开更多
文摘The present work involves the development of siliconized epoxy resin to overcome the drawback of epoxy resin like poor impact strength, high rigidity and moisture absorbing nature because of which they are not applied as corrosion resistant coating. By embedding silicone into the back bone of polymeric resin the above drawback can be reduced to substantial level. For achieving this, siliconised epoxy resins were prepared by reacting amine terminated silicone resin with novolac epoxy resin and meta-phenylenediamine was used as curing agent. The applied films of coating were baked at 150oC. Cured films were evaluated for their thermal, mechanical, chemical and corrosion resistance properties to ascertain the commercial utility of these eco-friendly resin for use in anti corrosive formulations. The siliconized epoxy resins system was found to exhibit good thermal and anticorrosive properties.
文摘Electrochemical impedance spectroscopy (EIS) in the l00 kHz-10 mHz frequency range was employed as the main electrochemical technique to study the corrosion protection behaviour of zinc rich epoxy paint in 3% NaCl solution. The EIS results obtained at the open-circuit corrosion potential have been interpreted using a model involving the impedance of particle to particle contact to account for the increasing resistance between zinc particles with immersion period, in addition to the impedance due to the zinc surface oxide layer and the electrical resistivity of the binder. Galvanic current and dc potential measurements allowed us to conclude that the cathodic protection effect of the paint takes some time to be achieved. The loss of cathodic protection is due to a double effect: the decrease of the Zn/Fe area ratio due to Zn corrosion and the loss of electric contact between Zn to Zn particles. Even when the cathodic protection effect by Zn dust become weak, the substrate steel is still protected against corrosion due to the barrier nature of the ZRP film reinforced by Zn.
文摘Coating slurries for making anodes and cathodes of lithium batteries contain a large percentage of solid particles of different chemicals, sizes and shapes in highly viscous media. A thorough mixing of these slurries poses a major challenge in the battery manufacturing process. Several types of mixing devices and mixing methods were examined. The conventional turbine stirrers or ball mill mixers could be adequately used for the preparation of anode slurries, but not suitable for cathode slurries. In this study, a newly three-dimensional mixer, in conjunction with a multi-stage mixing sequence was proposed. The mixing effectiveness was examined by means of rheological measurements and flow visualization techniques. Preliminary electrical performance results indicated that the battery obtained using the 3D mixing device with a multi-stage mixing sequence was more efficient to those obtained from conventional methods.
文摘This paper describes a concept for an independent and redundant safety concept for Lithium batteries in Electric and Hybrid Electric Vehicles. This concept includes an emergency cooling system based on pressurized carbon dioxide (CO2). Since carbon dioxide (CO2) is a possible medium of future mobile air conditioning (MAC) systems, the MAC system can be utilized for the one-time emergency cooling described in this paper. In the first part of the paper, some major safety aspects of automotive Li batteries are highlighted. In the second section, the paper describes a technical approach, how these batteries can be made safer. Pressurized CO2, which is a promising candidate for cooling liquids used in future mobile air conditioning (MAC) systems, is used to effectively cool down an overheating or up-heating battery in a critical state. The safety system thereby is not based on an electrical effect, but on a direct and fast-reacting thermal conduction, avoiding a thermal runaway of individual cells. The application of the proposed system is to act preventively just before the thermal runaway gets uncontrollable. In this case, the limited amount of CO2, which is available in the MAC system, fulfils the emergency cooling requirements. The combination of standard car components for the concept leads to an only moderate increase of the total weight and the additional system costs. Therefore, the described system might be of interest for car, battery and air conditioning system producers. This paper explains that the synergetic combination of CO2-based MAC systems and Li-based batteries is an innovative approach to improve environmental compatibility in future vehicles. The concept is proven experimentally on a lab scale with battery cells and battery packs consisting of four serially connected cells, respectively.
文摘In this paper we demonstrate that the residual stress introduced by several different surface finishes affects the critical current density for passivation and the passive current density in the anodic polarization curve of austenitic stainless steel and that those critical current densities can be reduced by controlling the residual stress by applying a cavitating jet to the backs of specimens. The results show that the current density either increased or decreased depending on the surface finish, and that was decreased by introducing compressive residual stress for all surface finishes.
文摘The performance of a newly designed tri-lobe industrial lobe pump of high capacity is simulated by using commercial CFD solver Ansys Fluent. A combination of user-defined-functions and meshing strategies is employed to capture the rotation of the lobes. The numerical model is validated by comparing the simulated results with the literature values. The processes of suction, displacement, compression and exhaust are accurately captured in the transient simulation. The fluid pressure value remains in the range of inlet pressure value till the processes of suction and displacement are over. The instantaneous process of compression is accurately captured in the simulation. The movement of a particular working chamber is traced along the gradual degree of lobe’s rotation. At five different degrees of lobe’s rotation, pressure contour plots are reported which clearly shows the pressure values inside the working chamber. Each pressure value inside the working chamber conforms to the particular process in which the working chamber is operating. Finally, the power requirement at the shaft of rotation is estimated from the simulated values. The estimated value of power requirement is 3.61 BHP FHP whereas the same calculated theoretically is 3 BHP FHP. The discrepancy is attributed to the assumption of symmetry of blower along the thickness.
文摘Currently a technique widely used for gold extraction is mercury by amalgamation technique, the tailing produced pollutes water of all kinds, so it is necessary to develop a form of selective mitigation, for which it is necessary to use complexing agents based on calixarene functionalized with mercury sequestering agents. These are immobilized by adding supports based on natural silica to form polymers and make them insoluble in all types of solvents, so that they can be used as an extractor and at the same time regenerate to their original properties for continuous reuse.
文摘Lithium element has attracted remarkable attraction for energy storage devices, over the past 30 years. Lithium is a light element and exhibits the low atomic number 3, just after hydrogen and helium in the periodic table. The lithium atom has a strong tendency to release one electron and constitute a positive charge, as Li<sup> </sup>. Initially, lithium metal was employed as a negative electrode, which released electrons. However, it was observed that its structure changed after the repetition of charge-discharge cycles. To remedy this, the cathode mainly consisted of layer metal oxide and olive, e.g., cobalt oxide, LiFePO<sub>4</sub>, etc., along with some contents of lithium, while the anode was assembled by graphite and silicon, etc. Moreover, the electrolyte was prepared using the lithium salt in a suitable solvent to attain a greater concentration of lithium ions. Owing to the lithium ions’ role, the battery’s name was mentioned as a lithium-ion battery. Herein, the presented work describes the working and operational mechanism of the lithium-ion battery. Further, the lithium-ion batteries’ general view and future prospects have also been elaborated.
文摘A series of six pyrazoles was synthesized by Michael-type addition reaction. The molecules 5-amino-1-aryl-1H-pyrazole-4-carbonitrile (3a-f) were synthesized from (ethoxymethylene)malo-nonitrile (1) and fluorinated and non-fluorinated aryl hydrazines (2a-f) using ethanol and fluorinated ethanol as solvents at reflux. An excellent regio-selectivity was found when pyrazole derivatives were formed as an exclusive product. No other regioisomer or uncyclised hydrazide was observed. Their structures were confirmed by spectroscopy data (1H, 13C, 19F, COSY (correlation spectroscopy), HSQC (heteronuclear single-quantum correlation spectroscopy) and HMBC (heteronuclear multiple-bond correlation spectroscopy);MS (mass-spectrometry). The yields ranged from good to excellent (47% - 93%) under mild reaction conditions. It would indicate a high selectivity in the one-step work procedure. These products (3a-f) and derivatives have a potential academic and industrial use as key intermediates, in special, for application in crop protection.
文摘Large quantities of spent hydrodesulfurization (HDS) catalysts are available from petrochemical industry. Disposal of spent catalyst is a problem as it falls under the category of hazardous industrial waste due to its vanadium concentration. Most of these catalysts are usually supported on alumina containing a variable percentage of elements such as nickel or molybdenum. Hence these catalysts contain environmentally critical, and economically valuable metals such as molyb denum, vanadium, and, nickel. In this paper, a spent HDS catalyst was treated with caustic soda solution. Parameters such as temperature, time, and NaOH solution concentration have been studied thoroughly, in order to settle the appropriate conditions for the maximum recovery of molybdenum and vanadium. Under the best leaching conditions (20 %w NaOH, room temperature, 2 h) about 95% recovery of Mo and V was achieved, and the recovery of nickel obtained was of 99% in the form of NiAlO4.
文摘Water is the most abundant liquid on the surface of the earth. It is a liquid whose properties are quite surprising, both as a pure liquid and as a solvent. Water is a very cohesive liquid: its melting and vaporization temperatures are very high for a liquid that is neither ionic nor metallic, and whose molar mass is low. Thus, water remains liquid at atmospheric pressure up to 100C while similar molecules such as H2S, H2Se, H2Te for example would give a vaporization temperature close to 80C. This cohesion is in fact ensured by hydrogen bonds between water molecules. This type of bonds between neighboring molecules, hydrogen bonds, is quite often found in chemistry [1] [2]. Any change in the state of aggregation of a substance occurs with the absorption or release of a certain amount of latent heat of transformation. Latent heat of fusion, vaporization or sublimation is the ratio of the energy supplied as heat to the mass of the substance that is melted, vaporized or sublimated. As a result of the reversibility of the processes, the fusion heat is equal to the heat released in the reverse process: crystallization and solidification heat. And likewise the heat of vaporization is equal to the heat of condensation. This equality of heat is often used to determine experimentally either of these quantities. There are two main measurement methods: 1) Direct measurement using the calorimeter, 2) Indirect measure based on the use of the VantHoff relationship. The objective of this work is to measure the latent heat of water vaporization and verify the compatibility of the experimental values with the values given by the tables using the indirect method.
文摘In global industrialization, efforts have been made to increase the rate of heat transfer in heat exchanger, minimizing the size of heat exchanger to reduce cost as well as increasing the effectiveness. Helical coil heat exchanger (HCHE) has been proven to be effective in improving heat transfer due to its large surface area. In this study, HCHE was designed to provide hot air needed for fluidized bed drying processes. The HCHE design model was fabricated and evaluated to study the efficiency of the hot air output for a laboratory fluidized bed dryer. The mathematical model for estimation of the final (output) temperature of air, Taf, passing through the HCHE was developed and validated experimentally. The drying of bitter kola particulates was carried out with a drying temperature of 50C 3C and a bed height-to-bed diameter ratio (H/D) of 1.5. The time taken to dry bitter kola particulates to 0.4% moisture content was 1 hour 45 minutes. Hence, HCHE is recommended for use in the production of hot for laboratory-scale fluidized bed dryers.
文摘In this study, a homogeneous alkaline catalyst was used in the production of biodiesel from raw and refined castor oil feedstock. The effect of potassium hydroxide (KOH) as a catalyst between the two feedstocks, raw and refined castor oil was compared. The transesterification technique was utilized in this study, aiming to investigate the effect of different parameters, which include the reaction temperature, methanol-to-oil mole ratio, and catalyst concentration at a constant period of 90 minutes. The result revealed the performance of the KOH catalyst on raw castor oil yielded 98.49% FAME, which was higher than the refined castor oil which yielded 97.9% FAME. The optimal conditions obtained from refined castor oil were applied to raw castor oil because of the same properties. The fuel quality of castor oil and produced biodiesel were tested for physicochemical properties.
文摘In the emerging world of biotech innovation, the fast-to-clinic/market strategy has emerged as a critical “mantra” for biotech, investors, and CDMOs. This approach addresses the escalating costs and complexities of research and development by streamlining the path from concept to clinical trials and, ultimately, to market. The article delves into the intricacies of implementing a fast-to-clinic/market strategy, underlining the empowering role of strategic decision-making in preclinical and commercial stages. The plan advocates for a phase-appropriate approach, where the development decision is tailored to each phase of the product’s lifecycle. This ensures that resources are allocated efficiently, risks are managed effectively, and the product can move through the development pipeline accelerated without compromising quality or regulatory compliance. The article also discusses the role of CDMOs in facilitating rapid product development and the essential factors biotech companies must consider when selecting a partner for outsourcing. These factors include the CDMO’s expertise in navigating regulatory landscapes, technological capabilities, and ability to scale processes efficiently. Moreover, the article stresses the importance of agility and flexibility in the fast-to-clinic/market approach. Biotech companies are encouraged to adopt adaptable strategies that respond to the fast-evolving regulatory and market landscapes.
文摘Organic molecules that exhibit long persistent luminescence (LPL) are rapidly gaining attention for a variety of applications. In this study, organic molecules with simple structures were selected and organic long persistent luminescence (OLPL) crystals were prepared. The crystal structure of the prepared OLPL crystal was elucidated and the guideline for the design of OLPL crystal was clarified. LPL was observed in OLPL crystals prepared with TMB as the guest molecule and 1,2-bis(diphenylphosphino)ethane as the host molecule. XRD measurements of the OLPL crystals suggest that the guest molecule is a solid solution substituted in the stable crystal structure of the host molecule in a lattice-shrinking direction.
文摘In the present study, energetic and entropic changes are investigated on a comparative basis, as they occur in the volume changes of an ideal gas in the Carnot cycle and in the course of the chemical reaction in a lead-acid battery. Differences between reversible and irreversible processes have been worked out, in particular between reversibly exchanged entropy (∆<sub>e</sub>S) and irreversibly produced entropy (∆<sub>i</sub>S). In the partially irreversible case, ∆<sub>e</sub>S and ∆<sub>i</sub>S add up to the sum ∆S for the volume changes of a gas, and only this function has an exact differential. In a chemical reaction, however, ∆<sub>e</sub>S is independent on reversibility. It arises from the different intramolecular energy contents between products and reactants. Entropy production in a partially irreversible Carnot cycle is brought about through work-free expansions, whereas in the irreversible battery reaction entropy is produced via activated complexes, whereby a certain, variable fraction of the available chemical energy becomes transformed into electrical energy and the remaining fraction dissipated into heat. The irreversible reaction process via activated complexes has been explained phenomenologically. For a sufficiently high power output of coupled reactions, it is essential that the input energy is not completely reversibly transformed, but rather partially dissipated, because this can increase the process velocity and consequently its power output. A reduction of the counter potential is necessary for this purpose. This is not only important for man-made machines, but also for the viability of cells.
文摘With the full growth of energy needs in the world, several studies are now focused on finding renewable sources. The aim of this work is to optimise biofuel formulation from a mixture design by studying physical properties, such as specific gravity and kinematic viscosity of various formulated mixtures. Optimization from the mixture plan revealed that in the chosen experimental domain, the optimal conditions are: 40% for used frying oil (UFO), 50% for bioethanol and 10% for diesel. These experimental conditions lead to a biofuel with a density of 0.84 and a kinematic viscosity of 2.97 cSt. These parameters are compliant with the diesel quality certificate in tropical areas. These density and viscosity values were determined according to respective desirability values of 0.68 and 0.75.
文摘Nano-sized ZnO catalysts were prepared by a direct precipitation method under the optimal conditions (cal-cination of precursors at 550?C for 120 min). The as-synthesized ZnO catalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and UV-Vis spectroscopy. The photocatalytic prop-erties of ZnO nanoparticles were investigated via methyl orange (MO) as a model organic compound under UV light irradiation. The influence of operating parameters on MO degradation including the amount of ZnO catalysts, pH value of solutions, and the photodegradation temperature was thoroughly examined. In addition, the kinetic process of photocatalytic degradation of MO using nano-sized ZnO catalyst was also examined, and the degradation of MO follow the first order kinetics.
文摘Various concepts for oil evaporation prediction are summarized. Models can be divided into those models that use the basis of air-boundary-regulation or those that do not. Experiments were conducted to determine if oil and petroleum evaporation is regulated by the saturation of the air boundary layer. Experiments included the examination of the evaporation rate with and without wind, in which case it was found that evaporation rates were similar for all wind conditions and no-wind conditions. Experiments where the area and mass varied showed that boundary-layer regulation was not governing for petroleum products. Under all experimental and environmental conditions, oils or petroleum products were not found to be boundary-layer regulated. Experiments on the rate of evaporation of pure compounds showed that compounds larger than Decane were not boundary-layer regulated. Many oils and petroleum products contain few compounds smaller than decane, and this explains why their evaporation is not air boundary-layer limited. Comparison of the air saturation levels of various oils and petroleum products shows that the saturation concentration of water, which is strongly air boundary-regulated, is significantly less than that of several petroleum hydrocarbons. Lack of air boundary-layer regulation for oils is shown to be a result of both this higher saturation concentration as well as a low (below boundary-layer value) evaporation rate.
文摘The aim of this work was to investigate the aerobic degradation of high-strength industrial (refinery) wastewaters in the inverse fluidized bed biological reactor, in which polypropylene particles of density 910 kg/m3 were fluidized by an upward flow of gas through a bed. Measurements of chemical oxygen demand (COD) versus residence time t were performed for various ratios of settled bed volume to reactor volume (Vb/VR) and air velocities u. The largest COD reduction, namely, from 54,840 to 2,190 mg/l, i.e. a 96% COD decrease, was achieved when the reactor was operated at the ratio (Vb/VR) = 0.55, air velocity u = 0.046 m/s and t = 65 h. Thus, these values of (Vb/VR), u and t can be considered as the optimal operating parameters for a reactor when used in treatment of high-strength refinery wastewaters. In the treatment operation conducted in a reactor optimally controlled at (Vb/VR) = 0.55, u = 0.046 m/s and t = 65 h, the conversions obtained for all phenolic constituents of the wastewater were larger than 95%. The conversions of about 90% were attained for other hydrocarbons.
