SmCo based films with excellent intrinsic magnetic properties have promising applications in micro-electro-mechanical system(MEMS).However,due to the complexity of phase composition and uncontrollable crystallization ...SmCo based films with excellent intrinsic magnetic properties have promising applications in micro-electro-mechanical system(MEMS).However,due to the complexity of phase composition and uncontrollable crystallization degree of SmCo hard magnetic phase in the film,both the coercivity(Hc)and remanence(Mr)of films are difficult to enhance simultaneously.In this paper,SmCo based films were deposited with a Cr underlayer and capping layer on single crystal Si substrates via magnetron sputtering process.The effects of annealing parameters and Sm/Co atomic ratio on the phase structure and coercivity of films are discussed.By adjusting the Sm/Co atomic ratio from 1:5 to 1:4,Co soft magnetic phase disappears and the single phase SmCo5 is obtained,leading to the increase of coercivity of the films from 30 to 34 kOe.The influence of deposition temperature and Cu doping on magnetic properties of SmCo based films was investigated.When the deposition temperature increases from room temperature to 250℃,the coercivity will further increase from 34 to 51 kOe.However,a severe kink is observed in the demagnetization curves due to the poor exchanged coupling.An analysis of transmission electron microscopy(TEM)confirms that the average size of non-hard magnetic amorphous phase exceeds the effective exchanged coupling length of SmCo5,which contributes to the decoupling and low remanence ratio.Therefore,doping Cu and applying a post-annealing process can significantly improve the crystallization degree of the films.Both the coercivity and the remanence ratio of the demagnetization curves are greatly enhanced.We propose a plausible strategy to prepare the SmCo based films with high coercivity and remanence ratio by temperature and chemical optimization,which can be utilized in high performed MEMS devices.展开更多
Lanthanide （Ln, or rare-earth） doped nanoparticles are well-known for their prominent optical properties and have been widely used for biological applications, especially in biological assays and medical imaging. Re...Lanthanide （Ln, or rare-earth） doped nanoparticles are well-known for their prominent optical properties and have been widely used for biological applications, especially in biological assays and medical imaging. Recently, the extensive attention of near infrared （NIR） wavelength range has dramatically increased for its fast feedback, high spatial resolution and deep tissue penetration. Tissues have minimal absorbance in this region. While a lot of excellent reviews cover various aspects of biomedical imaging based on lanthanide doped nanoparticles, there has not been a review that systematically summarizes NIR-to-NIR imaging with lanthanide doped nanoparticles. In this review, we focus on the recent development of NIR-to-NIR imaging based on lanthanide doped nanoparticles, and discuss challenges and opportunities in it.展开更多
Under the working environment of high temperature and strong load impact,hot forging die is prone to failure which reduces the service life of die.Using arc additive manufacturing in the die cavity,a gradient material...Under the working environment of high temperature and strong load impact,hot forging die is prone to failure which reduces the service life of die.Using arc additive manufacturing in the die cavity,a gradient material hot forging die with high precision,superior per-formance,and conformal cooling channels is developed.This improves the toughness of the die cavity and reduces the working temperature,thereby forming an isothermal field,which is an effective method to enhance the lifespan of the hot forging die.Three kinds of gradient flux-cored wires are designed for the surface of 5CrNiMo steel,and the microstructure and mechanical properties between gradient interfaces were studied.Based on the spatial curved structure of shaped waterways in the hot forging die cavity,a study was conducted on the strategy of partitioned forming for the manufacturing of the die with shaped waterways.In order to avoid interference with the arc gun,the hot for-ging die is divided into four regions,namely the transition region,upper,middle,and lower region,based on a combination of cavity depth and internal U-shaped and quadrilateral structures.The results show that the developed flux-cored wires have good moldability with straight sides of deposited metal under different process parameters and flat surface without cracks,pores and other defects.Under the same working conditions,the life of hot forging die formed by the gradient materials is more than multiple times that of the single material hot forging die,and the temperature gradient field of the shaped waterway die is 7℃/cm smaller than that of traditional straight waterway.展开更多
基金Project supported by the National Key R&D Program of China(2022YFB3505700,2022YFB3807900)National Natural Science Foundation of China(51901079)+2 种基金R&D(Research and Development)Plan in Key Areas of Guangdong Province(SDZX2021002,212021032611700001)Natural Science Foundation of Guangdong Province(2020A1515010736,2021A1515010451)the Guangzhou Municipal Science and Technology Program(202007020008)。
文摘SmCo based films with excellent intrinsic magnetic properties have promising applications in micro-electro-mechanical system(MEMS).However,due to the complexity of phase composition and uncontrollable crystallization degree of SmCo hard magnetic phase in the film,both the coercivity(Hc)and remanence(Mr)of films are difficult to enhance simultaneously.In this paper,SmCo based films were deposited with a Cr underlayer and capping layer on single crystal Si substrates via magnetron sputtering process.The effects of annealing parameters and Sm/Co atomic ratio on the phase structure and coercivity of films are discussed.By adjusting the Sm/Co atomic ratio from 1:5 to 1:4,Co soft magnetic phase disappears and the single phase SmCo5 is obtained,leading to the increase of coercivity of the films from 30 to 34 kOe.The influence of deposition temperature and Cu doping on magnetic properties of SmCo based films was investigated.When the deposition temperature increases from room temperature to 250℃,the coercivity will further increase from 34 to 51 kOe.However,a severe kink is observed in the demagnetization curves due to the poor exchanged coupling.An analysis of transmission electron microscopy(TEM)confirms that the average size of non-hard magnetic amorphous phase exceeds the effective exchanged coupling length of SmCo5,which contributes to the decoupling and low remanence ratio.Therefore,doping Cu and applying a post-annealing process can significantly improve the crystallization degree of the films.Both the coercivity and the remanence ratio of the demagnetization curves are greatly enhanced.We propose a plausible strategy to prepare the SmCo based films with high coercivity and remanence ratio by temperature and chemical optimization,which can be utilized in high performed MEMS devices.
文摘Lanthanide （Ln, or rare-earth） doped nanoparticles are well-known for their prominent optical properties and have been widely used for biological applications, especially in biological assays and medical imaging. Recently, the extensive attention of near infrared （NIR） wavelength range has dramatically increased for its fast feedback, high spatial resolution and deep tissue penetration. Tissues have minimal absorbance in this region. While a lot of excellent reviews cover various aspects of biomedical imaging based on lanthanide doped nanoparticles, there has not been a review that systematically summarizes NIR-to-NIR imaging with lanthanide doped nanoparticles. In this review, we focus on the recent development of NIR-to-NIR imaging based on lanthanide doped nanoparticles, and discuss challenges and opportunities in it.
基金supported by the National Key R&D Program of China(No.2017YFB1103200).
文摘Under the working environment of high temperature and strong load impact,hot forging die is prone to failure which reduces the service life of die.Using arc additive manufacturing in the die cavity,a gradient material hot forging die with high precision,superior per-formance,and conformal cooling channels is developed.This improves the toughness of the die cavity and reduces the working temperature,thereby forming an isothermal field,which is an effective method to enhance the lifespan of the hot forging die.Three kinds of gradient flux-cored wires are designed for the surface of 5CrNiMo steel,and the microstructure and mechanical properties between gradient interfaces were studied.Based on the spatial curved structure of shaped waterways in the hot forging die cavity,a study was conducted on the strategy of partitioned forming for the manufacturing of the die with shaped waterways.In order to avoid interference with the arc gun,the hot for-ging die is divided into four regions,namely the transition region,upper,middle,and lower region,based on a combination of cavity depth and internal U-shaped and quadrilateral structures.The results show that the developed flux-cored wires have good moldability with straight sides of deposited metal under different process parameters and flat surface without cracks,pores and other defects.Under the same working conditions,the life of hot forging die formed by the gradient materials is more than multiple times that of the single material hot forging die,and the temperature gradient field of the shaped waterway die is 7℃/cm smaller than that of traditional straight waterway.
