The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste （MSW） was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN softwar...The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste （MSW） was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results.Simulated waste,representative of typical MSW with and without chlorine compounds,was burned at the background temperature of 700 and 950°C,respectively.In the absence of chlorine,the moisture content has no evident effect on the volatility of Pb,Zn and Cu at either 700 or 950°C,however,as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700°C and reduced at 950°C,respectively.In the presence of chlorine,the flue gas moisture reduced the volatility of Pb,Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides,and the reduction became significant as chlorine content increase.For Cd,the chlorine promotes its volatility through the formation of more volatile CdCl 2.As a result,the increased moisture content increases the Pb,Zn,Cu and Cd concentrations in the bottom ash,which limits the utilization of the bottom ash as a construction material.Therefore,in order to accumulate heavy metals into the fly ash,MSW should be dried before incineration.展开更多
The natural wind plays disadvantageous roles in the operation of air-cooled steam condensers in power plant.It is of use to take various measures against the adverse effect of wind for the performance improvement of a...The natural wind plays disadvantageous roles in the operation of air-cooled steam condensers in power plant.It is of use to take various measures against the adverse effect of wind for the performance improvement of air-cooled condensers.Based on representative 2×600 MW direct air-cooled power plant,three ways that can arrange and optimize the flow field of cooling air thus enhance the heat transfer of air-cooled condensers were proposed.The physical and mathematical models of air-cooled condensers with various flow leading measures were presented and the flow and temperature fields of cooling air were obtained by CFD simulation.The back pressures of turbine were calculated for different measures on the basis of the heat transfer model of air-cooled condensers.The results show that the performance of air-cooled condensers is improved thus the back pressure of turbine is lowered to some extent by taking measures against the adverse impact of natural wind.展开更多
The research of soil classification and soil grade evaluation is often based on fuzzy theory. So, the traditional method has an inevitable problem about weight matrix which given by some experts, and the final result ...The research of soil classification and soil grade evaluation is often based on fuzzy theory. So, the traditional method has an inevitable problem about weight matrix which given by some experts, and the final result can be influenced by artificial factors. The essentials of fuzzy synthetically judge is to handle the data of high dimension. That is to reducing the dimension number. The weight matrix in fuzzy theory is corresponding to low dimension projection value of each index. But we can′t define whether the weight matrix given by experts is the best projection value or not. So, the authors apply a new technique of falling dimension named projection pursuit to soil study, through using the improved real coding based accelerating genetic algorithm to optimize the projection direction. Thus, it can transfer multi dimension data into one dimension data, through searching for the optimum projection direction to realize the soil classification and its grade evaluation. The method can avoid the artificial disturbance, and acquire preferably effect. Thus, the paper provides a new method to the research of soil classification and grade evaluation.展开更多
In this paper, air side heat transfer and pressure drop characteristics of twelve three-row plate finandtube heat exchanger cores of four types of fin configurations have been experimentally investigated.The heat tran...In this paper, air side heat transfer and pressure drop characteristics of twelve three-row plate finandtube heat exchanger cores of four types of fin configurations have been experimentally investigated.The heat transfer and friction factor correlations for'the twelve cores are provided in a wide range ofReynolds number. It is found that in the range of Reynolds number tested, the Nusselt number of theslotted fin surface is the largest and that of the plain plate fin is the lowest while the Nusselt numbersof two types of wavy fins are somewhere in between.展开更多
Pre-dried sewage sludge with high sulfur content was combusted in an electrically heated lab-scale fluidized-bed incinerator. The emission characteristics of polychlorinated dibenzo-p-dioxins （PCDDs）, polychlorinate...Pre-dried sewage sludge with high sulfur content was combusted in an electrically heated lab-scale fluidized-bed incinerator. The emission characteristics of polychlorinated dibenzo-p-dioxins （PCDDs）, polychlorinated dibenzofurans （PCDFs） and polycyclic aromatic hydrocarbons （PAHs） were studied. Coal and calcium oxide （CaO） were added during the sewage sludge combustion tests to optimize combustion conditions and control SO2 emission. The results indicated that the flue gases emitted during mono-combustion of sewage sludge were characterized by relatively high concentrations of SO2, NOx and organic pollutants, due to the high sulfur, nitrogen, and volatile matter content of sewage sludge. The total 16 USEPA priority PAHs and 2,3,7,8-substituted PCDD/Fs produced from sewage sludge combustion were found to be 106.14 μg/m^3 and 8955.93 pg/m^3 in the flue gas, respectively. In the case of cocombustion with coal （msludge/mcoal =1：1）, the 16 PAHs and 2,3,7,8-substituted PCDD/Fs concentrations were markedly lower than those found during mono-combustion of sewage sludge. During co-combustion, a suppressant effect of CaO on PCDD/Fs formation was observed.展开更多
Start-up working condition is the key to the research of optimal engagementof automatic clutch for AMT. In order to guarantee an ideal dynamic performance of the clutchengagement, an optimal controller is designed by ...Start-up working condition is the key to the research of optimal engagementof automatic clutch for AMT. In order to guarantee an ideal dynamic performance of the clutchengagement, an optimal controller is designed by considering throttle angle, engine speed, gearratio, vehicle acceleration and road condition. The minimum value principle is also introduced toachieve an optimal dynamic performance of the nonlinear system compromised in friction plate wearand vehicle drive quality. The optimal trajectory of the clutch engagement can be described in theform of explicit and analytical expressions and characterized by the deterministic and accuratecontrol strategy in stead of indeterministic and soft control techniques which need thousands ofexperiments. For validation of the controller, test work is carried out for the automated clutchengagements in a commercial car with an traditional mechanical transmission, a hydraulic actuator, agroup of sensors and a portable computer system. It is shown through experiments that dynamicbehaviors of the clutch engagement operated by the optimal control are more effective and efficientthan those by fuzzy control.展开更多
Experiments of simultaneous removal of SO2 and NO from simulated flue gas,using NaClO2 solution as the absorbent,were carried out in a self-designed bubble reactor,and high simultaneous removal effi-ciencies of SO2 an...Experiments of simultaneous removal of SO2 and NO from simulated flue gas,using NaClO2 solution as the absorbent,were carried out in a self-designed bubble reactor,and high simultaneous removal effi-ciencies of SO2 and NO were obtained under the optimal experimental conditions.The mechanism of simultaneous removal based on NaClO2 acid solutions was proposed by analyzing the removal prod-ucts.Possibility and limitation of the desulfurization and denitrification using NaClO2 acid solutions were calculated by thermodynamic methods.Experimental results of reaction kinetics for simultaneous desulfurization and denitrification indicated that the oxidation-absorption processes of SO2 and NO were divided into two zones,namely the fast and slow reaction zones.In the slow reaction zones both were zero order reactions,and in the fast reaction zones,the reaction order,rate constant and activa-tion energy of SO2 reaction with absorbent were 1.4,1.22(mol.L-1)-0.4.s-1 and 66.25kJ.mol-1,respec-tively,and 2,3.15×103(mol.L-1)-1.s-1,and 42.50 kJ.mol-1 for NO reaction,respectively.展开更多
A new approach to determining the local boundaries of voltage stability region in power injection space (IVSR) for power system with wind farms is presented. It can be used for power system voltage stability analysis ...A new approach to determining the local boundaries of voltage stability region in power injection space (IVSR) for power system with wind farms is presented. It can be used for power system voltage stability analysis and on-line security assessment with considering the output uncertainty of the wind farms. Firstly, power flow tracing and double dispatching are used to determine the generators that are closely related to the wind farms, in order to balance the power fluctuations caused by the wind speed variation. Then, modal analysis is used to get the key generators to achieve an effective dimension reduction for IVSR. Finally, the forecasting output power (or wind speed) of wind farms is divided into several intervals. For each interval, the corresponding local IVSR boundaries can be calculated by the method based on small disturbance. Moreover, parallel process is used to accelerate the computing speed. The presented approach is validated by several power systems. It can be revealed that the approach can give the local IVSR boundaries at different wind speeds and has a good engineering application prospect.展开更多
The influence of diffuser parameters, including the riser spacing, port number in a riser, injection angle, port arrangement, etc., on the surface initial dilution is experimentally investigated. The relative density ...The influence of diffuser parameters, including the riser spacing, port number in a riser, injection angle, port arrangement, etc., on the surface initial dilution is experimentally investigated. The relative density difference between the effluent and the sea water in the model is the same as that in the prototype, and the effect of the cross current is simulated by an inverse model technique. Based on the result analysis, the arrangement with more ports in a riser and larger riser spacing is suggested to save construction cost. The relationship between the Reynolds number based on the port diameter and velocity, and the surface initial dilution is also explored, and the critical Reynolds number is proposed.展开更多
Using the finite element code ANSYS/LS-DYNA, a dynamic finite element modelwith an elastic-linear-kinematic-hardening plastic material is established to analyzeelastic-plastic stresses in the railhead in the impact pr...Using the finite element code ANSYS/LS-DYNA, a dynamic finite element modelwith an elastic-linear-kinematic-hardening plastic material is established to analyzeelastic-plastic stresses in the railhead in the impact process of wheel and rail occurring at thegap of rail joint. The model is based on the discrete elastic support condition of the rails, whichis suitable for the actual situation of wheel/track rolling contact. In the analysis the influencesof axle load, yield stress and tangent modulus of rail material on the stresses and strains areinvestigated in detail. The distribution of stresses and strains in the jointed railhead are given.It is found that the axle load, yield stress and tangent modulus of rail material greatly affect thestresses and strains in the railhead during impacting. The study provides a reliable method anduseful datum for the further research on fatigue and wear of railhead and improving the rail jointmode.展开更多
The advance in the wide-area measurement system (WAMS) is driving the power system to the trend of wide-area monitoring and control.The Prony method is usually used for low frequency oscillation online identification....The advance in the wide-area measurement system (WAMS) is driving the power system to the trend of wide-area monitoring and control.The Prony method is usually used for low frequency oscillation online identification.However,the identified amplitude and phase information is not sufficiently used.In this paper,the amplitude is adopted to detect the occurrence of the oscillation and to obtain the mode observability of the sites.The phase is adopted to identify the oscillation generator grouping and to obtain the mode shapes.The time varying characteristics of low frequency oscillations are studied.The behaviors and the characters of low frequency oscillations are displayed by dynamic visual techniques.Demonstrations on the "11.9" low frequency oscillation of the Guizhou Power Grid substantiate the feasibility and the validation of the proposed methods.展开更多
Two sets of silicon-based micro pulsating heat pipes(SMPHPs) with trapezoidal cross section having hydraulic diameters of 352 μm(#1) and 394 μm(#2) respectively were fabricated for the first time using MEMS technolo...Two sets of silicon-based micro pulsating heat pipes(SMPHPs) with trapezoidal cross section having hydraulic diameters of 352 μm(#1) and 394 μm(#2) respectively were fabricated for the first time using MEMS technology.With FC-72 as the working fluid,the start-up,steady operation state,as well as flow patterns were investigated using a CCD camera.It was found that the start-up process of these two SMPHPs was rather rapid.At the start-up period,no nucleation was observed,and the vapor plugs at the evaporator U-bends were formed mainly due to the breakup of liquid slugs.At the steady operation state,self-sustained oscillation with large amplitudes dominated the flow behavior when the inclination angle varied from 10° to 90°,but the nucleate boiling and bulk circulation were observed only in SMPHP #2.While bubbly,slug/plug,annular/semi-annular,and wavy-annular flows were observed in both two SMPHPs,the injection flow only appeared in SMPHP #2.展开更多
Compared with input-to-state stability(ISS) in global version,the concept of local input-to-state stability(LISS) is more relevant and meaningful in practice.The key of assessing LISS properties lies in investigating ...Compared with input-to-state stability(ISS) in global version,the concept of local input-to-state stability(LISS) is more relevant and meaningful in practice.The key of assessing LISS properties lies in investigating three main ingredients,the local region of initial states,the local region of external inputs and the asymptotic gain.It is the objective of this paper to propose a numerical algorithm for estimating LISS properties on the theoretical foundation of quadratic form LISS-Lyapunov function.Given developments of linear matrix inequality(LMI) methods,this algorithm is effective and powerful.A typical power electronics based system with common DC bus is served as a demonstration for quantitative results.展开更多
Based on the TiO2 photocatalysis mechanism, a new method of simultaneous desulfurization and denitrification from flue gas was proposed. Preparation of TiO2 photocatalyst, design of photocatalysis reactor and influenc...Based on the TiO2 photocatalysis mechanism, a new method of simultaneous desulfurization and denitrification from flue gas was proposed. Preparation of TiO2 photocatalyst, design of photocatalysis reactor and influencing factors for simul- taneous removal of SO2 and NO, and removal mechanism of SO2 and NO were studied. After the optimal values of concentration of O2 in flue gas, the relative humidity of flue gas and the irradiation time in the photocatalysis reactor were used, the efficiencies of removal for SO2 and NO can be achieved above 98% and about 67%, respectively. According to the results of removal products analysis, the re- moval mechanism of SO2 and NO based on TiO2 photocatlysis can be put forward, namely, SO2 was oxidized to SO3 partly, the bulk of NO was oxidized to NO2, and both were removed by resorbing finally.展开更多
Bentonite has been extensively studied because of its strong sorption ability and low permeability.In this work,the Na-bentonite from Gaomiaozi County (China) has been characterized by XRD,FTIR and acid-base titration...Bentonite has been extensively studied because of its strong sorption ability and low permeability.In this work,the Na-bentonite from Gaomiaozi County (China) has been characterized by XRD,FTIR and acid-base titration.The sorption of Eu(III) on Na-bentonite in the absence/presence of humic acid (HA) was studied at T = 25 ± 2 °C and in 0.01 mol/L NaClO4 solution.The effects of pH,HA,contact time and initial Eu(III) concentrations were also investigated.The results indicate that the sorption of Eu(III) on Na-bentonite was dependent on pH values.The presence of HA had little effect on Eu(III) sorption at low pH values,but decreased Eu(III) sorption at high pH values.X-ray absorption fine structure spectroscopy (XAFS) was applied to characterize the local structural environment of the adsorbed Eu(III) on bare Na-bentonite and HA-bentonite hybrids.The re- sults indicate that Eu(III) was bound to O atoms at a distance of about 2.39 at pH 4.15.The results are crucial for the evalua- tion of the sorption and migration of other trivalent lanthanides and actinides in bentonite as backfill materials.展开更多
基金supported by the National Natural Science Foundation of China (No. 50776007)the Beijing Municipal Science and Technology Commission under the Municipal Solid Waste Development Program(No. H020620330120)
文摘The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste （MSW） was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results.Simulated waste,representative of typical MSW with and without chlorine compounds,was burned at the background temperature of 700 and 950°C,respectively.In the absence of chlorine,the moisture content has no evident effect on the volatility of Pb,Zn and Cu at either 700 or 950°C,however,as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700°C and reduced at 950°C,respectively.In the presence of chlorine,the flue gas moisture reduced the volatility of Pb,Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides,and the reduction became significant as chlorine content increase.For Cd,the chlorine promotes its volatility through the formation of more volatile CdCl 2.As a result,the increased moisture content increases the Pb,Zn,Cu and Cd concentrations in the bottom ash,which limits the utilization of the bottom ash as a construction material.Therefore,in order to accumulate heavy metals into the fly ash,MSW should be dried before incineration.
基金supported by the National Basic Research Program of China ("973" Project) (Grant No.2009CB219804)
文摘The natural wind plays disadvantageous roles in the operation of air-cooled steam condensers in power plant.It is of use to take various measures against the adverse effect of wind for the performance improvement of air-cooled condensers.Based on representative 2×600 MW direct air-cooled power plant,three ways that can arrange and optimize the flow field of cooling air thus enhance the heat transfer of air-cooled condensers were proposed.The physical and mathematical models of air-cooled condensers with various flow leading measures were presented and the flow and temperature fields of cooling air were obtained by CFD simulation.The back pressures of turbine were calculated for different measures on the basis of the heat transfer model of air-cooled condensers.The results show that the performance of air-cooled condensers is improved thus the back pressure of turbine is lowered to some extent by taking measures against the adverse impact of natural wind.
文摘The research of soil classification and soil grade evaluation is often based on fuzzy theory. So, the traditional method has an inevitable problem about weight matrix which given by some experts, and the final result can be influenced by artificial factors. The essentials of fuzzy synthetically judge is to handle the data of high dimension. That is to reducing the dimension number. The weight matrix in fuzzy theory is corresponding to low dimension projection value of each index. But we can′t define whether the weight matrix given by experts is the best projection value or not. So, the authors apply a new technique of falling dimension named projection pursuit to soil study, through using the improved real coding based accelerating genetic algorithm to optimize the projection direction. Thus, it can transfer multi dimension data into one dimension data, through searching for the optimum projection direction to realize the soil classification and its grade evaluation. The method can avoid the artificial disturbance, and acquire preferably effect. Thus, the paper provides a new method to the research of soil classification and grade evaluation.
文摘In this paper, air side heat transfer and pressure drop characteristics of twelve three-row plate finandtube heat exchanger cores of four types of fin configurations have been experimentally investigated.The heat transfer and friction factor correlations for'the twelve cores are provided in a wide range ofReynolds number. It is found that in the range of Reynolds number tested, the Nusselt number of theslotted fin surface is the largest and that of the plain plate fin is the lowest while the Nusselt numbersof two types of wavy fins are somewhere in between.
基金supported by the Important Project on Science and Technology of Zhejiang Province of China(No. 2007C03003)the National Natural Science Foundation of China (No. 50576082)
文摘Pre-dried sewage sludge with high sulfur content was combusted in an electrically heated lab-scale fluidized-bed incinerator. The emission characteristics of polychlorinated dibenzo-p-dioxins （PCDDs）, polychlorinated dibenzofurans （PCDFs） and polycyclic aromatic hydrocarbons （PAHs） were studied. Coal and calcium oxide （CaO） were added during the sewage sludge combustion tests to optimize combustion conditions and control SO2 emission. The results indicated that the flue gases emitted during mono-combustion of sewage sludge were characterized by relatively high concentrations of SO2, NOx and organic pollutants, due to the high sulfur, nitrogen, and volatile matter content of sewage sludge. The total 16 USEPA priority PAHs and 2,3,7,8-substituted PCDD/Fs produced from sewage sludge combustion were found to be 106.14 μg/m^3 and 8955.93 pg/m^3 in the flue gas, respectively. In the case of cocombustion with coal （msludge/mcoal =1：1）, the 16 PAHs and 2,3,7,8-substituted PCDD/Fs concentrations were markedly lower than those found during mono-combustion of sewage sludge. During co-combustion, a suppressant effect of CaO on PCDD/Fs formation was observed.
文摘Start-up working condition is the key to the research of optimal engagementof automatic clutch for AMT. In order to guarantee an ideal dynamic performance of the clutchengagement, an optimal controller is designed by considering throttle angle, engine speed, gearratio, vehicle acceleration and road condition. The minimum value principle is also introduced toachieve an optimal dynamic performance of the nonlinear system compromised in friction plate wearand vehicle drive quality. The optimal trajectory of the clutch engagement can be described in theform of explicit and analytical expressions and characterized by the deterministic and accuratecontrol strategy in stead of indeterministic and soft control techniques which need thousands ofexperiments. For validation of the controller, test work is carried out for the automated clutchengagements in a commercial car with an traditional mechanical transmission, a hydraulic actuator, agroup of sensors and a portable computer system. It is shown through experiments that dynamicbehaviors of the clutch engagement operated by the optimal control are more effective and efficientthan those by fuzzy control.
基金Supported by the National High-Tech Research and Development Program of China("863" Project)(Grant No.2007AA061803)
文摘Experiments of simultaneous removal of SO2 and NO from simulated flue gas,using NaClO2 solution as the absorbent,were carried out in a self-designed bubble reactor,and high simultaneous removal effi-ciencies of SO2 and NO were obtained under the optimal experimental conditions.The mechanism of simultaneous removal based on NaClO2 acid solutions was proposed by analyzing the removal prod-ucts.Possibility and limitation of the desulfurization and denitrification using NaClO2 acid solutions were calculated by thermodynamic methods.Experimental results of reaction kinetics for simultaneous desulfurization and denitrification indicated that the oxidation-absorption processes of SO2 and NO were divided into two zones,namely the fast and slow reaction zones.In the slow reaction zones both were zero order reactions,and in the fast reaction zones,the reaction order,rate constant and activa-tion energy of SO2 reaction with absorbent were 1.4,1.22(mol.L-1)-0.4.s-1 and 66.25kJ.mol-1,respec-tively,and 2,3.15×103(mol.L-1)-1.s-1,and 42.50 kJ.mol-1 for NO reaction,respectively.
基金supported by National Natural Science Foundation of China (Grant No. 50707019)Special Fund of the National Basic Research Program of China ("973" Program) (Grant Nos. 2009CB219701, 2010CB234600)+1 种基金Tianjin Municipal Science and Technology Development Program (Grant No. 09JCZDJC25000)Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20090032110064)
文摘A new approach to determining the local boundaries of voltage stability region in power injection space (IVSR) for power system with wind farms is presented. It can be used for power system voltage stability analysis and on-line security assessment with considering the output uncertainty of the wind farms. Firstly, power flow tracing and double dispatching are used to determine the generators that are closely related to the wind farms, in order to balance the power fluctuations caused by the wind speed variation. Then, modal analysis is used to get the key generators to achieve an effective dimension reduction for IVSR. Finally, the forecasting output power (or wind speed) of wind farms is divided into several intervals. For each interval, the corresponding local IVSR boundaries can be calculated by the method based on small disturbance. Moreover, parallel process is used to accelerate the computing speed. The presented approach is validated by several power systems. It can be revealed that the approach can give the local IVSR boundaries at different wind speeds and has a good engineering application prospect.
文摘The influence of diffuser parameters, including the riser spacing, port number in a riser, injection angle, port arrangement, etc., on the surface initial dilution is experimentally investigated. The relative density difference between the effluent and the sea water in the model is the same as that in the prototype, and the effect of the cross current is simulated by an inverse model technique. Based on the result analysis, the arrangement with more ports in a riser and larger riser spacing is suggested to save construction cost. The relationship between the Reynolds number based on the port diameter and velocity, and the surface initial dilution is also explored, and the critical Reynolds number is proposed.
基金National Natural Science Foundation of China(No.599355100)Foundation for Excellent PhD Thesis of University of Ministry of Education of China (No.200048)
文摘Using the finite element code ANSYS/LS-DYNA, a dynamic finite element modelwith an elastic-linear-kinematic-hardening plastic material is established to analyzeelastic-plastic stresses in the railhead in the impact process of wheel and rail occurring at thegap of rail joint. The model is based on the discrete elastic support condition of the rails, whichis suitable for the actual situation of wheel/track rolling contact. In the analysis the influencesof axle load, yield stress and tangent modulus of rail material on the stresses and strains areinvestigated in detail. The distribution of stresses and strains in the jointed railhead are given.It is found that the axle load, yield stress and tangent modulus of rail material greatly affect thestresses and strains in the railhead during impacting. The study provides a reliable method anduseful datum for the further research on fatigue and wear of railhead and improving the rail jointmode.
基金supported by the National Natural Science Foundation of China (Grant No. 50595413)
文摘The advance in the wide-area measurement system (WAMS) is driving the power system to the trend of wide-area monitoring and control.The Prony method is usually used for low frequency oscillation online identification.However,the identified amplitude and phase information is not sufficiently used.In this paper,the amplitude is adopted to detect the occurrence of the oscillation and to obtain the mode observability of the sites.The phase is adopted to identify the oscillation generator grouping and to obtain the mode shapes.The time varying characteristics of low frequency oscillations are studied.The behaviors and the characters of low frequency oscillations are displayed by dynamic visual techniques.Demonstrations on the "11.9" low frequency oscillation of the Guizhou Power Grid substantiate the feasibility and the validation of the proposed methods.
基金supported by the National Natural Science Foundation of China (Grant No 50925624)the Program for New Century Excellent Talents in University of China (Grant No NCET-06-0406)the Shanghai Municipal Education Commission (Grant Nos 08ZZ10 and 08GG05)
文摘Two sets of silicon-based micro pulsating heat pipes(SMPHPs) with trapezoidal cross section having hydraulic diameters of 352 μm(#1) and 394 μm(#2) respectively were fabricated for the first time using MEMS technology.With FC-72 as the working fluid,the start-up,steady operation state,as well as flow patterns were investigated using a CCD camera.It was found that the start-up process of these two SMPHPs was rather rapid.At the start-up period,no nucleation was observed,and the vapor plugs at the evaporator U-bends were formed mainly due to the breakup of liquid slugs.At the steady operation state,self-sustained oscillation with large amplitudes dominated the flow behavior when the inclination angle varied from 10° to 90°,but the nucleate boiling and bulk circulation were observed only in SMPHP #2.While bubbly,slug/plug,annular/semi-annular,and wavy-annular flows were observed in both two SMPHPs,the injection flow only appeared in SMPHP #2.
基金supported by the National Natural Science Foundation of China (Grant Nos 50977047 and 50907038)
文摘Compared with input-to-state stability(ISS) in global version,the concept of local input-to-state stability(LISS) is more relevant and meaningful in practice.The key of assessing LISS properties lies in investigating three main ingredients,the local region of initial states,the local region of external inputs and the asymptotic gain.It is the objective of this paper to propose a numerical algorithm for estimating LISS properties on the theoretical foundation of quadratic form LISS-Lyapunov function.Given developments of linear matrix inequality(LMI) methods,this algorithm is effective and powerful.A typical power electronics based system with common DC bus is served as a demonstration for quantitative results.
文摘Based on the TiO2 photocatalysis mechanism, a new method of simultaneous desulfurization and denitrification from flue gas was proposed. Preparation of TiO2 photocatalyst, design of photocatalysis reactor and influencing factors for simul- taneous removal of SO2 and NO, and removal mechanism of SO2 and NO were studied. After the optimal values of concentration of O2 in flue gas, the relative humidity of flue gas and the irradiation time in the photocatalysis reactor were used, the efficiencies of removal for SO2 and NO can be achieved above 98% and about 67%, respectively. According to the results of removal products analysis, the re- moval mechanism of SO2 and NO based on TiO2 photocatlysis can be put forward, namely, SO2 was oxidized to SO3 partly, the bulk of NO was oxidized to NO2, and both were removed by resorbing finally.
基金supported by the National Natural Science Foundation of China (20971126, 20907055 & 20677058)973 project from Ministry of Science and Technology of ChinaSpecial Foundation of High-level Waste Disposal (2007-840)
文摘Bentonite has been extensively studied because of its strong sorption ability and low permeability.In this work,the Na-bentonite from Gaomiaozi County (China) has been characterized by XRD,FTIR and acid-base titration.The sorption of Eu(III) on Na-bentonite in the absence/presence of humic acid (HA) was studied at T = 25 ± 2 °C and in 0.01 mol/L NaClO4 solution.The effects of pH,HA,contact time and initial Eu(III) concentrations were also investigated.The results indicate that the sorption of Eu(III) on Na-bentonite was dependent on pH values.The presence of HA had little effect on Eu(III) sorption at low pH values,but decreased Eu(III) sorption at high pH values.X-ray absorption fine structure spectroscopy (XAFS) was applied to characterize the local structural environment of the adsorbed Eu(III) on bare Na-bentonite and HA-bentonite hybrids.The re- sults indicate that Eu(III) was bound to O atoms at a distance of about 2.39 at pH 4.15.The results are crucial for the evalua- tion of the sorption and migration of other trivalent lanthanides and actinides in bentonite as backfill materials.
