Tensile tests of GH4169 alloy were performed at room temperature. Different fractions, distributions and shapes of δ phase was prepared by aging treated at 880 ℃, 930 ℃ and 980 ℃ for 5 h or 10 h. The effect of δ ...Tensile tests of GH4169 alloy were performed at room temperature. Different fractions, distributions and shapes of δ phase was prepared by aging treated at 880 ℃, 930 ℃ and 980 ℃ for 5 h or 10 h. The effect of δ phase on the mechanical pro- perties of GH4169 alloy was investigated. The results show that 0.2% yield strength and ultimate tensile strength of GH4169 alloy increase by 61 MPa and 78 MPa respectively when the fraction of δ phase increases from 2.20% to 5.21%. Then, the ultimate tensile strength remains at 1 012 MPa even when the fraction of δ phase reaches 7.56%. The fraction effect of δ phase on the strength improvement of GH4169 alloy is more significant than morphology, and the critical fraction value is 5.21%. In addition, the elongation decreases by 14.1% when the fraction of δ phase increases from 2.20% to 7.56%. Excessive needle or short rod shaped 8 ohase is resoonsible for the reduction of eloneation.展开更多
The flow behavior and dynamic globularization of TC11 titanium alloy during subtransus deformation are investigated through hot compression tests. A constitutive model is established based on physical-based hardening ...The flow behavior and dynamic globularization of TC11 titanium alloy during subtransus deformation are investigated through hot compression tests. A constitutive model is established based on physical-based hardening model and phenomenological softening model. And based on the recrystallization mechanisms of globularization, the Avrami type kinetics model is established for prediction of globularization fraction and globularized grain size under large strain subtransus deformation of TC11 alloy. As the preliminary application of the previous results, the cogging process of large size TC11 alloy billet is simulated. Based on subroutine development of the DEFORM software, the coupled simulation of one fire cogging process is developed. It shows that the predicted results are in good agreement with the experimental results in forging load and microstructure characteristic, which validates the reliability of the developed FEM subroutine models.展开更多
Thin-walled copper tubes are usually produced by multi-pass float-plug drawing deformation.In general,the annealing treatment subsequently is necessary to release the stored energy and adjusts the microstructure.In th...Thin-walled copper tubes are usually produced by multi-pass float-plug drawing deformation.In general,the annealing treatment subsequently is necessary to release the stored energy and adjusts the microstructure.In this study,an investigation on the evolution of annealing twins as well as textures in the thin-walled(Φ6 mm×0.3 mm)copper tube underwent holding time-free heat treatment was reported.Electron backscattered diffraction analysis reveals that a large number ofΣ3 boundaries(600<111>twin relationship)are produced at the early stage of heat treatment,which is due to the lower boundary energy.With the recrystallization proceeding,the migration rate of grain boundaries decreases on account of the grain growth;meanwhile,the uniqueΣ9 boundaries(38.9°<110>relationship)are formed due to the interaction of theΣ3 boundaries.As a result,the number fractions ofΣ3 boundaries and high-angle grain boundaries decrease rapidly.During the grain growth stage,a strong recrystallization texture was formed due to the fact that the grains of Goss orientation have a growth advantage over the others.As a result,the initial copper texture was transferred into the Goss texture in domination.展开更多
Natural products have long been a crucial source of,or provided inspiration for new agrochemical discovery.Naturally occurring 18β-glycyrrhetinic acid shows broad-spectrum bioactivities and is a potential skeleton fo...Natural products have long been a crucial source of,or provided inspiration for new agrochemical discovery.Naturally occurring 18β-glycyrrhetinic acid shows broad-spectrum bioactivities and is a potential skeleton for novel drug discovery.To extend the utility of 18β-glycyrrhetinic acid for agricultural uses,a series of novel 18β-glycyrrhetinic acid amide derivatives were prepared and evaluated for their antibacterial potency.Notably,compound 5k showed good antibacterial activity in vitro against Xanthomonas oryzae pv.oryzae(Xoo,EC50=3.64 mg L–1),and excellent protective activity(54.68%)against Xoo in vivo.Compound 5k induced excessive production and accumulation of reactive oxygen species in the tested pathogens,resulting in damaging the bacterial cell envelope.More interestingly,compound 5k could increase the activities of plant defense enzymes including catalase,superoxide dismutase,peroxidase,and phenylalanine ammonia lyase.Taken together,these enjoyable results suggested that designed compounds derived from 18β-glycyrrhetinic acid showed potential for controlling intractable plant bacterial diseases by disturbing the balance of the phytopathogen’s redox system and activating the plant defense system.展开更多
The TP2 copper tube was prepared with La microalloying by horizontal continuous casting(HCC). The absorptivity of La and its effects on microstructure, tensile and corrosion properties of HCC TP2 copper tube were stud...The TP2 copper tube was prepared with La microalloying by horizontal continuous casting(HCC). The absorptivity of La and its effects on microstructure, tensile and corrosion properties of HCC TP2 copper tube were studied by means of the inductively coupled plasma optical emission spectrometer(ICP-OES), optical microscope(OM), scanning electron microscope(SEM) and potentiodynamic polarization measurements. The results show that the absorptivity of La in the HCC TP2 copper tube is about 15% under antivacuum conditions due to the good chemical activities of La. The impurity elements in copper tube such as O, S, Pb and Si can be significantly reduced, and the average columnar dendrite spacing of the copper tube can also be reduced from 2.21 mm to 0.93 mm by adding La. The ultimate tensile strength and the elongation with and without La addition are almost unchanged. However, the annual corrosion rate of the HCC TP2 copper tube is reduced from 10.18 mm·a^(-1) to 9.37 mm·a^(-1) by the purification effect of trace La.展开更多
Due to the improvement in fatigue strength of cold-rolled blades,the static recrystallization behavior of cold-rolled Inconel 718 alloy in the solid solution treatment was investigated with the methods of optical micr...Due to the improvement in fatigue strength of cold-rolled blades,the static recrystallization behavior of cold-rolled Inconel 718 alloy in the solid solution treatment was investigated with the methods of optical microscopy and electron backscattered diffraction.The effect ofδphase precipitation on the static recrystallization process was also analyzed.The results show thatδphase preferentially precipitates comparing to static recrystallization.Affecting by theδphase preferential precipitation process,sub-grain migration is the main nucleation mechanism in the static recrystallization of coldrolled Inconel 718 alloy at 980°C.Meanwhile,strain-induced boundary migration also exists as an aided nucleation mechanism when the rolling reduction is less than 30%.展开更多
Analysis of the recently proposed equal channel angular bending(ECAB)process is provided on thin hotrolled AZ31 magnesium alloy sheets.In particular,effects of deformation temperature and strain path on the texture ev...Analysis of the recently proposed equal channel angular bending(ECAB)process is provided on thin hotrolled AZ31 magnesium alloy sheets.In particular,effects of deformation temperature and strain path on the texture evolution and mechanical properties are systematically investigated under single pass ECAB at various temperatures and multi-pass ECAB process that involves changes in strain paths.It is found that simultaneous activation of multiple twinning types is successfully introduced during ECAB,which results in obvious tilted component of basal texture.Attributed to the domination of extension twins,weaker basal textures are detected after both single pass ECAB at 150℃and three cross passes ECAB at 200℃.After annealing,the basal texture is further weakened via twin-related recrystallization and the annealed microstructure is featured with mixture of basal and non-basal orientated grains.Additionally,the effect of grain orientation on the mode of plastic deformation and the roles of grain orientation and grain boundary on the local strain accommodation are coherently studied.This study reveals that over 60%increase of uniform elongation with marginal reduction of tensile strength less than 5%can be achieved for single pass ECAB at 150℃and three cross passes ECAB at 200℃,which is the result of larger fraction of grains favored with extension twinning and better local strain accommodation.展开更多
Deformation and texture evolution of AZ31 B magnesium（Mg） alloy sheet under uniaxial tension, compression, and reverse loading after different pre-strain（compression and tension） were investigated experimentally. ...Deformation and texture evolution of AZ31 B magnesium（Mg） alloy sheet under uniaxial tension, compression, and reverse loading after different pre-strain（compression and tension） were investigated experimentally. The results indicate that the pre-compressive strain remarkably affects the reverse tensile yield stress and the width of the detwinning-dominant stage during inverse tension process. Similar to stress–strain curve of the uniaxial compression, the curve of reverse tensile yield value also has ‘S＇ shape, and its minimum value is only 38 MPa. The relationship between pre-compressive strain and the width of detwinning-dominant stage presents a linear growth, and the greater the precompressive strain is, the smaller the strain hardening rate of the detwinning-slip-dominant stage is. Compared with the reverse tension under pre-compression, the influence of the pre-tension deformation on the deformation mechanism of subsequent compression is relatively simple. With the increase in pre-tension strain, the yield stress of the reverse loading is rising.展开更多
Developments of new sheet metal forming technology and theory in China are reviewed in detail in this paper.Advances of crystal plasticity on the deformation mechanism of Mg alloy are firstly described, especially its...Developments of new sheet metal forming technology and theory in China are reviewed in detail in this paper.Advances of crystal plasticity on the deformation mechanism of Mg alloy are firstly described, especially its applications on the prediction of sheet forming process. Then, a new macroscopic constitutive model is introduced, which possesses an enhanced description capacity of tension/compression anisotropy and anisotropic hardening. In order to take into account the twinning process of hexagonal close-packed material, a modified hierarchical multi-scale model is also established with adequate accuracy in a shorter computational time. The advanced forming limit of sheet metal, mainly about aluminum alloy, is also investigated. Besides the above theory developments, some new sheet metal forming technologies are reviewed simultaneously. The warm forming technology of Mg alloy is discussed. New processes to form sheet parts and to bend tubes are proposed by using hard granules. On the other hand, a new kind of ultra-high-strength steel based on typical22 Mn B5 by introducing more residual austenite and Cu-rich phase to increase the elongation and strength and its novel forming method that integrates hot stamping and quenching participation are proposed. Progresses in sheet hydroforming,press forging and electromagnetic forming of sheet metal parts are also summarized.展开更多
The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous cast...The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous casting characterize time variation,multiple disturbances and strong coupling.As a consequence,their influence on a casting billet is difficult to be determined.Due to the above issues,the common factor and special factor analysis of the factor analysis model were used in this study,and the casting experiment and billet metallographic experiment were carried out to diagnose and analyze the reason of the microstructure inhomogeneity.The multiple process parameters were studied and classified using common factor analysis,2 the cast billets with abnormal microstructures were identified by GT^(2) statistics,and the most important factors affecting the microstructural homogeneity were found by special factor analysis.The calculated and experimental results show that the principal parameters influencing the inhomogeneity of solidified microstructure are the primary inlet water pressure and the primary outlet water temperature.According to the consequence of the above investigation,the inhomogeneity of the copper billet microstructure can be effectively improved when the process parameters are controlled and adjusted.展开更多
The evolution of microstructure,textures,and mechanical properties of thin-walled copper tube during heat treatment was investigated using EBSD technique and tensile test.The results show that the initial deformation ...The evolution of microstructure,textures,and mechanical properties of thin-walled copper tube during heat treatment was investigated using EBSD technique and tensile test.The results show that the initial deformation textures of pre-drawn thin-walled copper tube are mainly composed of Copper and Y components,while with the increase of temperatures,the textures are transformed into a strong Goss texture gradually.The high-resolution microstructural characterizations indicate that the new Goss recrystallized grains nucleate and grow up within the deformed Copper grains and Y grains in different mechanisms,respectively.The tensile strength of the thin-walled copper tube decreases gradually with the increase of the temperature,while the elongation increases first and then decreases sharply due to the action of grain sizes and texture components.展开更多
Twinning and detwinning are the important deformation modes in magnesium alloys during cyclic loading at room temperature. To analyze these two deformation mechanism, cyclic compression–tension experiments were perfo...Twinning and detwinning are the important deformation modes in magnesium alloys during cyclic loading at room temperature. To analyze these two deformation mechanism, cyclic compression–tension experiments were performed on Mg–3Al–1Zn rolled sheet along the rolling direction. In these tests, the microstructure evolutions of a series of grains during deformation were traced by using quasi in situ electron backscatter diffraction(EBSD). Important quantities like the Schmid factors of twinning system, the fraction of twinning during compression, and the fraction of twinning after reverse loading were calculated on the basis of measured quantities. The influence of Schmid factor of twinning variants on detwinning upon reverse loading was analyzed. Detwinning would prefer to proceed during reverse loading if the Schmid factor of twinning in the twinning area before reverse loading is sufficiently large.展开更多
The healing behavior of micropores in powder metallurgy （P/M） 316L stainless steel during hot forging and subsequent heat treatment was studied. The results showed that hot forging can improve the homogeneity of the...The healing behavior of micropores in powder metallurgy （P/M） 316L stainless steel during hot forging and subsequent heat treatment was studied. The results showed that hot forging can improve the homogeneity of the pore size and enhance the relative density of material in varying degree due to different forging temperatures. As a re- sult of deformation and diffusion bonding at high temperature, the irregular pores were spheroidized and finally turned into stable inner grain pores. The comparison of compression behavior between P/M and wrought dense mate rials has shown that the pores can either be the obstacles of dislocation movement or be the nucleation sites accelera- ting the reerystallization according to the difference of deformation temperatures.展开更多
The influence of interfaces on the magneto-optical Kerr effect in the Co/Ni multilayer has been investigated.It was found that the magnetic-optical Kerr rotation varies with the numbers of interfaces(x)in Co/Ni multil...The influence of interfaces on the magneto-optical Kerr effect in the Co/Ni multilayer has been investigated.It was found that the magnetic-optical Kerr rotation varies with the numbers of interfaces(x)in Co/Ni multilayer,which indicated that the interface states play an important role in the Kerr effect.Moreover,ellipticity and optical constants n and k are also found to vary with x.Some possible mechanisms have been discussed.展开更多
基金Sponsored by the Fund of China State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals,Lanzhou University of Technology(SKLAB02014001)
文摘Tensile tests of GH4169 alloy were performed at room temperature. Different fractions, distributions and shapes of δ phase was prepared by aging treated at 880 ℃, 930 ℃ and 980 ℃ for 5 h or 10 h. The effect of δ phase on the mechanical pro- perties of GH4169 alloy was investigated. The results show that 0.2% yield strength and ultimate tensile strength of GH4169 alloy increase by 61 MPa and 78 MPa respectively when the fraction of δ phase increases from 2.20% to 5.21%. Then, the ultimate tensile strength remains at 1 012 MPa even when the fraction of δ phase reaches 7.56%. The fraction effect of δ phase on the strength improvement of GH4169 alloy is more significant than morphology, and the critical fraction value is 5.21%. In addition, the elongation decreases by 14.1% when the fraction of δ phase increases from 2.20% to 7.56%. Excessive needle or short rod shaped 8 ohase is resoonsible for the reduction of eloneation.
文摘The flow behavior and dynamic globularization of TC11 titanium alloy during subtransus deformation are investigated through hot compression tests. A constitutive model is established based on physical-based hardening model and phenomenological softening model. And based on the recrystallization mechanisms of globularization, the Avrami type kinetics model is established for prediction of globularization fraction and globularized grain size under large strain subtransus deformation of TC11 alloy. As the preliminary application of the previous results, the cogging process of large size TC11 alloy billet is simulated. Based on subroutine development of the DEFORM software, the coupled simulation of one fire cogging process is developed. It shows that the predicted results are in good agreement with the experimental results in forging load and microstructure characteristic, which validates the reliability of the developed FEM subroutine models.
基金financially supported by the Natural Science Foundation of Shandong Province under Grant No.ZR2018MEE005。
文摘Thin-walled copper tubes are usually produced by multi-pass float-plug drawing deformation.In general,the annealing treatment subsequently is necessary to release the stored energy and adjusts the microstructure.In this study,an investigation on the evolution of annealing twins as well as textures in the thin-walled(Φ6 mm×0.3 mm)copper tube underwent holding time-free heat treatment was reported.Electron backscattered diffraction analysis reveals that a large number ofΣ3 boundaries(600<111>twin relationship)are produced at the early stage of heat treatment,which is due to the lower boundary energy.With the recrystallization proceeding,the migration rate of grain boundaries decreases on account of the grain growth;meanwhile,the uniqueΣ9 boundaries(38.9°<110>relationship)are formed due to the interaction of theΣ3 boundaries.As a result,the number fractions ofΣ3 boundaries and high-angle grain boundaries decrease rapidly.During the grain growth stage,a strong recrystallization texture was formed due to the fact that the grains of Goss orientation have a growth advantage over the others.As a result,the initial copper texture was transferred into the Goss texture in domination.
基金fundings provided by the National Natural Science Foundation of China(21877021 and 32160661)the Guizhou Provincial S&T Program[(2018)4007]the Program of Introducing Talents of Discipline to Universities of China(D20023,111 Program).
文摘Natural products have long been a crucial source of,or provided inspiration for new agrochemical discovery.Naturally occurring 18β-glycyrrhetinic acid shows broad-spectrum bioactivities and is a potential skeleton for novel drug discovery.To extend the utility of 18β-glycyrrhetinic acid for agricultural uses,a series of novel 18β-glycyrrhetinic acid amide derivatives were prepared and evaluated for their antibacterial potency.Notably,compound 5k showed good antibacterial activity in vitro against Xanthomonas oryzae pv.oryzae(Xoo,EC50=3.64 mg L–1),and excellent protective activity(54.68%)against Xoo in vivo.Compound 5k induced excessive production and accumulation of reactive oxygen species in the tested pathogens,resulting in damaging the bacterial cell envelope.More interestingly,compound 5k could increase the activities of plant defense enzymes including catalase,superoxide dismutase,peroxidase,and phenylalanine ammonia lyase.Taken together,these enjoyable results suggested that designed compounds derived from 18β-glycyrrhetinic acid showed potential for controlling intractable plant bacterial diseases by disturbing the balance of the phytopathogen’s redox system and activating the plant defense system.
基金financially supported by the Plan of the Chinese Academy of Sciences(CAS)to Provide Science&Technology(S&T)Support and Service for National Strategic Emerging Industries(Grant No.:2012037)the Science Foundation of the Chinese Academy of Sciences(Grant No.:2012005)
文摘The TP2 copper tube was prepared with La microalloying by horizontal continuous casting(HCC). The absorptivity of La and its effects on microstructure, tensile and corrosion properties of HCC TP2 copper tube were studied by means of the inductively coupled plasma optical emission spectrometer(ICP-OES), optical microscope(OM), scanning electron microscope(SEM) and potentiodynamic polarization measurements. The results show that the absorptivity of La in the HCC TP2 copper tube is about 15% under antivacuum conditions due to the good chemical activities of La. The impurity elements in copper tube such as O, S, Pb and Si can be significantly reduced, and the average columnar dendrite spacing of the copper tube can also be reduced from 2.21 mm to 0.93 mm by adding La. The ultimate tensile strength and the elongation with and without La addition are almost unchanged. However, the annual corrosion rate of the HCC TP2 copper tube is reduced from 10.18 mm·a^(-1) to 9.37 mm·a^(-1) by the purification effect of trace La.
基金National Natural Science Foundation of China(Grant No.51505240)Natural Science Foundation of Zhejiang(Grant No.LQ19E050004)+1 种基金Special Inventive Fund of Science and Technology in Shenyang(Grant No.Fl5-172-6-00)the State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals.Lanzhou University of Technology(Grant No.SKLAB02014001).
文摘Due to the improvement in fatigue strength of cold-rolled blades,the static recrystallization behavior of cold-rolled Inconel 718 alloy in the solid solution treatment was investigated with the methods of optical microscopy and electron backscattered diffraction.The effect ofδphase precipitation on the static recrystallization process was also analyzed.The results show thatδphase preferentially precipitates comparing to static recrystallization.Affecting by theδphase preferential precipitation process,sub-grain migration is the main nucleation mechanism in the static recrystallization of coldrolled Inconel 718 alloy at 980°C.Meanwhile,strain-induced boundary migration also exists as an aided nucleation mechanism when the rolling reduction is less than 30%.
基金supports from KIAT(Project No.N0002598)NRF of Korea(ERC Grant No.2019R1A5A6099595)。
文摘Analysis of the recently proposed equal channel angular bending(ECAB)process is provided on thin hotrolled AZ31 magnesium alloy sheets.In particular,effects of deformation temperature and strain path on the texture evolution and mechanical properties are systematically investigated under single pass ECAB at various temperatures and multi-pass ECAB process that involves changes in strain paths.It is found that simultaneous activation of multiple twinning types is successfully introduced during ECAB,which results in obvious tilted component of basal texture.Attributed to the domination of extension twins,weaker basal textures are detected after both single pass ECAB at 150℃and three cross passes ECAB at 200℃.After annealing,the basal texture is further weakened via twin-related recrystallization and the annealed microstructure is featured with mixture of basal and non-basal orientated grains.Additionally,the effect of grain orientation on the mode of plastic deformation and the roles of grain orientation and grain boundary on the local strain accommodation are coherently studied.This study reveals that over 60%increase of uniform elongation with marginal reduction of tensile strength less than 5%can be achieved for single pass ECAB at 150℃and three cross passes ECAB at 200℃,which is the result of larger fraction of grains favored with extension twinning and better local strain accommodation.
基金supported by the National Nature Science Foundation of China (No. 51174189)
文摘Deformation and texture evolution of AZ31 B magnesium（Mg） alloy sheet under uniaxial tension, compression, and reverse loading after different pre-strain（compression and tension） were investigated experimentally. The results indicate that the pre-compressive strain remarkably affects the reverse tensile yield stress and the width of the detwinning-dominant stage during inverse tension process. Similar to stress–strain curve of the uniaxial compression, the curve of reverse tensile yield value also has ‘S＇ shape, and its minimum value is only 38 MPa. The relationship between pre-compressive strain and the width of detwinning-dominant stage presents a linear growth, and the greater the precompressive strain is, the smaller the strain hardening rate of the detwinning-slip-dominant stage is. Compared with the reverse tension under pre-compression, the influence of the pre-tension deformation on the deformation mechanism of subsequent compression is relatively simple. With the increase in pre-tension strain, the yield stress of the reverse loading is rising.
文摘Developments of new sheet metal forming technology and theory in China are reviewed in detail in this paper.Advances of crystal plasticity on the deformation mechanism of Mg alloy are firstly described, especially its applications on the prediction of sheet forming process. Then, a new macroscopic constitutive model is introduced, which possesses an enhanced description capacity of tension/compression anisotropy and anisotropic hardening. In order to take into account the twinning process of hexagonal close-packed material, a modified hierarchical multi-scale model is also established with adequate accuracy in a shorter computational time. The advanced forming limit of sheet metal, mainly about aluminum alloy, is also investigated. Besides the above theory developments, some new sheet metal forming technologies are reviewed simultaneously. The warm forming technology of Mg alloy is discussed. New processes to form sheet parts and to bend tubes are proposed by using hard granules. On the other hand, a new kind of ultra-high-strength steel based on typical22 Mn B5 by introducing more residual austenite and Cu-rich phase to increase the elongation and strength and its novel forming method that integrates hot stamping and quenching participation are proposed. Progresses in sheet hydroforming,press forging and electromagnetic forming of sheet metal parts are also summarized.
基金This work is financially supported by Basic Scientific Project of Liaoning Provincial Department of Education(LJKMZ20220591)Science and Technology Plan Project of Changzhou,China(CQ20220057).
文摘The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous casting characterize time variation,multiple disturbances and strong coupling.As a consequence,their influence on a casting billet is difficult to be determined.Due to the above issues,the common factor and special factor analysis of the factor analysis model were used in this study,and the casting experiment and billet metallographic experiment were carried out to diagnose and analyze the reason of the microstructure inhomogeneity.The multiple process parameters were studied and classified using common factor analysis,2 the cast billets with abnormal microstructures were identified by GT^(2) statistics,and the most important factors affecting the microstructural homogeneity were found by special factor analysis.The calculated and experimental results show that the principal parameters influencing the inhomogeneity of solidified microstructure are the primary inlet water pressure and the primary outlet water temperature.According to the consequence of the above investigation,the inhomogeneity of the copper billet microstructure can be effectively improved when the process parameters are controlled and adjusted.
基金financially supported by the China Postdoctoral Science Foundation(No.2019M662276)the Chinese Academy of Science and Technology Service Network Planning(No.KFJ-STS-QYZD-145)。
文摘The evolution of microstructure,textures,and mechanical properties of thin-walled copper tube during heat treatment was investigated using EBSD technique and tensile test.The results show that the initial deformation textures of pre-drawn thin-walled copper tube are mainly composed of Copper and Y components,while with the increase of temperatures,the textures are transformed into a strong Goss texture gradually.The high-resolution microstructural characterizations indicate that the new Goss recrystallized grains nucleate and grow up within the deformed Copper grains and Y grains in different mechanisms,respectively.The tensile strength of the thin-walled copper tube decreases gradually with the increase of the temperature,while the elongation increases first and then decreases sharply due to the action of grain sizes and texture components.
基金financially supported by the National Natural Science Foundation of China(Nos.50775211 and51174189)
文摘Twinning and detwinning are the important deformation modes in magnesium alloys during cyclic loading at room temperature. To analyze these two deformation mechanism, cyclic compression–tension experiments were performed on Mg–3Al–1Zn rolled sheet along the rolling direction. In these tests, the microstructure evolutions of a series of grains during deformation were traced by using quasi in situ electron backscatter diffraction(EBSD). Important quantities like the Schmid factors of twinning system, the fraction of twinning during compression, and the fraction of twinning after reverse loading were calculated on the basis of measured quantities. The influence of Schmid factor of twinning variants on detwinning upon reverse loading was analyzed. Detwinning would prefer to proceed during reverse loading if the Schmid factor of twinning in the twinning area before reverse loading is sufficiently large.
基金Item Sponsored by National Basic Research Program of China(2012CB619600)
文摘The healing behavior of micropores in powder metallurgy （P/M） 316L stainless steel during hot forging and subsequent heat treatment was studied. The results showed that hot forging can improve the homogeneity of the pore size and enhance the relative density of material in varying degree due to different forging temperatures. As a re- sult of deformation and diffusion bonding at high temperature, the irregular pores were spheroidized and finally turned into stable inner grain pores. The comparison of compression behavior between P/M and wrought dense mate rials has shown that the pores can either be the obstacles of dislocation movement or be the nucleation sites accelera- ting the reerystallization according to the difference of deformation temperatures.
基金Supported by the Beijing Natural Science Foundationpartially by the National Natural Science Foundation of China under Grant Nos.59871063 and 59928101.
文摘The influence of interfaces on the magneto-optical Kerr effect in the Co/Ni multilayer has been investigated.It was found that the magnetic-optical Kerr rotation varies with the numbers of interfaces(x)in Co/Ni multilayer,which indicated that the interface states play an important role in the Kerr effect.Moreover,ellipticity and optical constants n and k are also found to vary with x.Some possible mechanisms have been discussed.
