In order to study the deformation behavior and evaluate the workability of the dual-phase Mg-9Li-3Al-2Sr alloy, isothermal hot compression tests were conducted using the Gleeble-3500 thermal-mechanical simulator, in r...In order to study the deformation behavior and evaluate the workability of the dual-phase Mg-9Li-3Al-2Sr alloy, isothermal hot compression tests were conducted using the Gleeble-3500 thermal-mechanical simulator, in ranges of elevated temperatures （423-573 K） and strain rates （0.001-1 s^-1）. Plastic instability is evident during the deformation which is in the form of serrated flow; serrated yielding is attributed to the locking of mobile dislocations by the Mg and Li atoms which diffuse during the deformation. The relationships between flow stress, strain rate and deformation temperature were analyzed and the deformation activation energy and some basic material factors at different strains were calculated using the Arrhenius equation. The effects of temperature and strain rate on deformation behavior were represented using the Zener–Hollomon parameter in an exponent-type equation. To verify the validity of the constitutive model, the predicted values and experimental flow curves under different deformation conditions were compared, the correlation coefficient （0.9970） and average absolute relative error （AARE=4.41%） were calculated. The results indicate that the constitutive model can be used to accurately predict the flow behavior of dual-phase Mg-9Li-3Al-2Sr alloy during high temperature deformation.展开更多
Mg−1Mn−0.5Al−0.5Ca−0.5Zn(wt.%)alloy was fabricated by conventional extrusion at 673 K with an extrusion ratio of 25:1,followed by aging at 473 K.The microstructure was characterized by scanning electron microscopy,ele...Mg−1Mn−0.5Al−0.5Ca−0.5Zn(wt.%)alloy was fabricated by conventional extrusion at 673 K with an extrusion ratio of 25:1,followed by aging at 473 K.The microstructure was characterized by scanning electron microscopy,electron back-scattered diffraction,and transmission electron microscopy.The mechanical properties were determined by the tensile test.The peak-aged sample shows fine recrystallized grains with an average grain size of 1.7μm.Area fraction of Al−Ca particles in the alloy increases significantly after peak aging.Meanwhile,botháañandác+añdislocations were observed to remain in the alloy after hot extrusion.Thus,the peak-aged sample exhibits simultaneously high strength and good ductility with the ultimate tensile stress,tensile yield stress,and tension fracture elongation of 320 MPa,314 MPa,and 19.0%,respectively.展开更多
基金Projects(CDJZR14130007106112015CDJXY130011)supported by Fundamental Research Funds for the Central Universities,China
文摘In order to study the deformation behavior and evaluate the workability of the dual-phase Mg-9Li-3Al-2Sr alloy, isothermal hot compression tests were conducted using the Gleeble-3500 thermal-mechanical simulator, in ranges of elevated temperatures （423-573 K） and strain rates （0.001-1 s^-1）. Plastic instability is evident during the deformation which is in the form of serrated flow; serrated yielding is attributed to the locking of mobile dislocations by the Mg and Li atoms which diffuse during the deformation. The relationships between flow stress, strain rate and deformation temperature were analyzed and the deformation activation energy and some basic material factors at different strains were calculated using the Arrhenius equation. The effects of temperature and strain rate on deformation behavior were represented using the Zener–Hollomon parameter in an exponent-type equation. To verify the validity of the constitutive model, the predicted values and experimental flow curves under different deformation conditions were compared, the correlation coefficient （0.9970） and average absolute relative error （AARE=4.41%） were calculated. The results indicate that the constitutive model can be used to accurately predict the flow behavior of dual-phase Mg-9Li-3Al-2Sr alloy during high temperature deformation.
基金the financial supports from the Fundamental Research Funds for the Central Universities,China(Nos.2019CDCGCL316,2020CDJDPT001)Chongqing Research Program of Basic Research and Frontier Technology,China(No.cstc2019jcjy-msxmX0539)。
文摘Mg−1Mn−0.5Al−0.5Ca−0.5Zn(wt.%)alloy was fabricated by conventional extrusion at 673 K with an extrusion ratio of 25:1,followed by aging at 473 K.The microstructure was characterized by scanning electron microscopy,electron back-scattered diffraction,and transmission electron microscopy.The mechanical properties were determined by the tensile test.The peak-aged sample shows fine recrystallized grains with an average grain size of 1.7μm.Area fraction of Al−Ca particles in the alloy increases significantly after peak aging.Meanwhile,botháañandác+añdislocations were observed to remain in the alloy after hot extrusion.Thus,the peak-aged sample exhibits simultaneously high strength and good ductility with the ultimate tensile stress,tensile yield stress,and tension fracture elongation of 320 MPa,314 MPa,and 19.0%,respectively.
