A series of copper-based activated carbon (AC) adsorbents were prepared in order to investigate the effect of Zn, Ce addition on Cu-based AC adsorbent for phosphine (PH3) adsorption removal from yellow phosphorous tai...A series of copper-based activated carbon (AC) adsorbents were prepared in order to investigate the effect of Zn, Ce addition on Cu-based AC adsorbent for phosphine (PH3) adsorption removal from yellow phosphorous tail gas. N2 adsorption isotherm and X-ray diffrac-tion (XRD) results suggested that the addition of Zn could increase the adsorbent ultramicropores, decrease the adsorbent supermicropores and the adsorbent average pore diameter. Therefore it enhanced the PH3 adsorption capacity. Appropriate amoun...展开更多
Phosphine(PH3) is a highly toxic air pollutant,commonly produced in phosphorous chemical industry.But it has received less research attention due to its handling difficultly.CO is the main content of the phosphorous c...Phosphine(PH3) is a highly toxic air pollutant,commonly produced in phosphorous chemical industry.But it has received less research attention due to its handling difficultly.CO is the main content of the phosphorous chemical industry tail gas,the concentration of which is always more than 80 vol.%,and it can be the feed gas to produce various valuable products such as formate,oxalate,and methanol and so on.But,PH3 is one of the important barriers,which is harmful to the following chemical process.In order to make use of the tail gas,PH3 should be removed firstly,and CO should be covered in the whole purified procedure at the same time.In this work,the modified activated carbon(MAC) was used as the adsorbent to separate PH3 from the mixture tail gas.Series of MAC adsorbents were prepared for the adsorption of PH3,which loaded Cu-Fe and Ce(La),or separately.The PH3 adsorption capacities,chemical and physical properties of MAC were all investigated.The results showed that over 99% PH3 adsorption efficiency was achieved when used MAC adsorbents.The removal efficiency and PH3 adsorption capacity of the Cu-Fe-Ce/AC(20:1:0.4) were both much higher than those modified activated carbons.The maximum PH3 adsorption capacity was 71 mg of PH3/g of MAC on the Cu-Fe-Ce/AC,which were much higher than literature data using CuO only for adsorbing hydride gases.展开更多
基金Project supported by the Key Program of National High Technology Research and Development Program of China (863 Program) (2008AA062602)the Young and Middle-aged Academic and Technical Back-up Personnel Program of Yunnan Province (2007PY01-10)the Analysis and Measurement Foundation of Kunming University of Science & Technology
文摘A series of copper-based activated carbon (AC) adsorbents were prepared in order to investigate the effect of Zn, Ce addition on Cu-based AC adsorbent for phosphine (PH3) adsorption removal from yellow phosphorous tail gas. N2 adsorption isotherm and X-ray diffrac-tion (XRD) results suggested that the addition of Zn could increase the adsorbent ultramicropores, decrease the adsorbent supermicropores and the adsorbent average pore diameter. Therefore it enhanced the PH3 adsorption capacity. Appropriate amoun...
基金Project supported by the Key Program of National High Technology Research and Development Program of China (863 Program) (2008AA062602)the Young and Middle-aged Academic and Technical Back-up Personnel Program of Yunnan Province (2007PY01-10)
文摘Phosphine(PH3) is a highly toxic air pollutant,commonly produced in phosphorous chemical industry.But it has received less research attention due to its handling difficultly.CO is the main content of the phosphorous chemical industry tail gas,the concentration of which is always more than 80 vol.%,and it can be the feed gas to produce various valuable products such as formate,oxalate,and methanol and so on.But,PH3 is one of the important barriers,which is harmful to the following chemical process.In order to make use of the tail gas,PH3 should be removed firstly,and CO should be covered in the whole purified procedure at the same time.In this work,the modified activated carbon(MAC) was used as the adsorbent to separate PH3 from the mixture tail gas.Series of MAC adsorbents were prepared for the adsorption of PH3,which loaded Cu-Fe and Ce(La),or separately.The PH3 adsorption capacities,chemical and physical properties of MAC were all investigated.The results showed that over 99% PH3 adsorption efficiency was achieved when used MAC adsorbents.The removal efficiency and PH3 adsorption capacity of the Cu-Fe-Ce/AC(20:1:0.4) were both much higher than those modified activated carbons.The maximum PH3 adsorption capacity was 71 mg of PH3/g of MAC on the Cu-Fe-Ce/AC,which were much higher than literature data using CuO only for adsorbing hydride gases.
