The creep of a skin layer under a distributed surface pressure was solved by ananalysical method using Hankel transform and Laplace transform.The surface stressboundary conditions lead io a Volterra integral equation ...The creep of a skin layer under a distributed surface pressure was solved by ananalysical method using Hankel transform and Laplace transform.The surface stressboundary conditions lead io a Volterra integral equation of the first kind, which was then solved by a numerical method.The IMSL subroutines DINLAP and DGORUL were employed to numerically obtain the Hankel-Laplace inversion. The calculateddisplacements at two distinctive moments were compared respectively with those obtained by an elastic solution for either incompressible or compressible solid. Thetransient creep responses of the skin layer were also presented.展开更多
The tensile creep resistance of Mg-5.5%Zn-(0.7%, 1.5%, 3.5%, 7.5%)Y(mass fraction, %) gravity-casting alloys was investigated systematically. The corresponding physical models were established for analyzing the micros...The tensile creep resistance of Mg-5.5%Zn-(0.7%, 1.5%, 3.5%, 7.5%)Y(mass fraction, %) gravity-casting alloys was investigated systematically. The corresponding physical models were established for analyzing the microstructure evolution and creep mechanism. The results show that four second phases are found in Mg-5.5%Zn-(0.7%, 1.5%, 3.5%, 7.5%)Y alloys, including Mg3 Zn Y, Mg3Zn6 Y, Mg3Zn3Y2 and Mg7Zn3, where the rare earth rich phase(Mg3Zn Y, Mg3Zn6 Y, Mg3Zn3Y2) with high melting point can more effectively improve the creep resistance properties of alloys than Mg7Zn3. With the increasing of Y content, the creep resistance of alloys is improved correspondingly. The alloys with(1.5%, 3.5%)Y addition exhibit high creep resistance at temperatures from 175 °C to 200 °C and load from 55 MPa to 70 MPa. The 7.5%Y added alloy presents excellent creep resistance even at 275 °C and 55 MPa. The second phase which shows discontinuous distribution at the grain boundary of(0.7%, 1.5%, 3.5%)Y added alloys has preferred orientation and clogs in triple junctions of grain boundary. Simultaneously, the arrangement of second phase particles along tensile direction and the formation of denuded zones are observed during the creep process. Moreover, the crack initiates in these areas and propagates along grain boundary. Compared with discontinuous second phase, the continuous skeleton-like second phase of 7.5%Y added alloy at grain boundary has a better effect on improving the creep resistance properties of alloys.展开更多
文摘The creep of a skin layer under a distributed surface pressure was solved by ananalysical method using Hankel transform and Laplace transform.The surface stressboundary conditions lead io a Volterra integral equation of the first kind, which was then solved by a numerical method.The IMSL subroutines DINLAP and DGORUL were employed to numerically obtain the Hankel-Laplace inversion. The calculateddisplacements at two distinctive moments were compared respectively with those obtained by an elastic solution for either incompressible or compressible solid. Thetransient creep responses of the skin layer were also presented.
基金Project(14JJ1013)supported by Natural Science Foundation of Hunan ProvinceChina
文摘The tensile creep resistance of Mg-5.5%Zn-(0.7%, 1.5%, 3.5%, 7.5%)Y(mass fraction, %) gravity-casting alloys was investigated systematically. The corresponding physical models were established for analyzing the microstructure evolution and creep mechanism. The results show that four second phases are found in Mg-5.5%Zn-(0.7%, 1.5%, 3.5%, 7.5%)Y alloys, including Mg3 Zn Y, Mg3Zn6 Y, Mg3Zn3Y2 and Mg7Zn3, where the rare earth rich phase(Mg3Zn Y, Mg3Zn6 Y, Mg3Zn3Y2) with high melting point can more effectively improve the creep resistance properties of alloys than Mg7Zn3. With the increasing of Y content, the creep resistance of alloys is improved correspondingly. The alloys with(1.5%, 3.5%)Y addition exhibit high creep resistance at temperatures from 175 °C to 200 °C and load from 55 MPa to 70 MPa. The 7.5%Y added alloy presents excellent creep resistance even at 275 °C and 55 MPa. The second phase which shows discontinuous distribution at the grain boundary of(0.7%, 1.5%, 3.5%)Y added alloys has preferred orientation and clogs in triple junctions of grain boundary. Simultaneously, the arrangement of second phase particles along tensile direction and the formation of denuded zones are observed during the creep process. Moreover, the crack initiates in these areas and propagates along grain boundary. Compared with discontinuous second phase, the continuous skeleton-like second phase of 7.5%Y added alloy at grain boundary has a better effect on improving the creep resistance properties of alloys.
